Having problems with your Vacuums ?

Inoperable electrical wall socket - Vacuums

Answers :

The obvious would be a blown fuse or tripped circuit breaker. Go to your main fuse box and check for that. If you have a GFI outlet or circuit breaker, reset that.\015\012Some outlets protected by Ground Fault Interrupters are gang wired, so there may be another outlet in the room that has the GFI outlet that controls the outlet you are using. You may have to check for them. The GFI outlet usually has two small push buttons on it, one is TEST and the other is RESET.
\015\012If it is not easily fixed by those items, you will most likely need to pull the outlet from the wall box and see if you can trace it from there.\015\012First check these as they are the easiest fixes.\015\012
\015\012If you find my solution to be of help, I would appreciate a Thumbs Up from you.\015\012If my solution does not solve your problem, please contact me and we can go from there.\015\012Paul
Is problem solved?
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Inoperable electrical wall socket - Vacuums

The obvious would be a blown fuse or tripped circuit breaker. Go to your main fuse box and check for that. If you have a GFI outlet or circuit breaker, reset that.\015\012Some outlets protected by Ground Fault Interrupters are gang wired, so there ... Vacuums

I was vacuuming and the power abruptly stopped working. The plug had slightly slid out of the wall socket, but when I put it back in, it wouldn't power up again. The wall socket is working for other appliances.

The first thing to suspect is that the wall plug on the vacuum cleaner is defective, to confirm this you will need to access the on/off switch on the vacuum, there will be three wires coming to the switch from the cord ... Hoover S1361 Bagged Canister Vacuum

Hooked everything up per directions. I plugged it in to the closest electrical outlet and nothing happened. The lights did not light up, the connected wall control and sensors leds do not light up. It appears the unit doesn't have power. The electrical outlet socket is fine as everything else I plug into it works fine. I have tried every other electrical outlet available. The unit won't power on from any outlet, and all of those outlets run other things, like power tools an refrigerators

Dear Davehibshman,Firstly; dismantle the plug and replace the fuse with the same rating as the one you have just taken out. Replace the plug cover, put the plug into the socket and try again. If this doesnt work, there may be a problem wi ... Vacuums

Why does my Hertiage II vacuum seem to be getting no power although it is plugged into the electrical socket? Does the vacuum have a motor that might br blown?

Check to see if there are any breaks in the cord, like any of the insulation missing.Also unplug it and feel along the cord for any unusual lumps. ... Kirby Heritage II Vacuum

Kenmore model #116.22650C vacuum cleaner will not shut off; I need to umplug it off the electric wall outlet.

... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

My electrolux Elite 3500 SR vacuum cleaner just quit working. I plugged it into wall socket and turned on switch and nothing happened.

... Vacuums

The electricity in the apt attached to my house lost power in two of the walls. It happened when the cleaning ladies I think were using a vacuum, they don't speak english very well so I'm not sure. I have looked at the circuit breaker a # of times and nothing seems to have been tripped. I have also inspected the outlets and they seem to be fine. Can you help me?

Even know the breaker doesn't look tripped it might be. You have to flip it all the way off and then back on again. That is most likely what has happened. If that doesn't work check to make sure a GFI hasn't tripped. They are usually loc ... Vacuums

My hoover, self propelled windtunnel ,on off switch will not shutoff. the second the electrical plug is put in the wall socket, the vacum starts running and you cannot shut it down with the on off switch

... Hoover Vacuums

I can't get the power switch on my DC25 to turn the vacuum off. I have to plug it in to the electrical socket and then unplug it to turn off. Suggestions?

It's probably the on/off switchI found a cool hint at http://www.fixya.com/support/t7785183-trying_remove hope this helps you ... Dyson DC25 All Floors Bagless Upright Vacuum

Model 116.1260 i can not figure out how to turn this vacuum on. is there a switch or do you just insert the hose into the wall socket?

Need the complete model #, 116.1260*****. I assume this is a built-in system? Yes you have to plug the hose into the wall outlet, and there usually is a switch on the hose handle to turn it on. ... Vacuums

My central vac wouldn't shut off when I took the hose out of the wall socket, I have to plug and unplug the unit at the electrical outlet.

The start stop command is done by a small switch that is located in the wall socket - this command is then transmitted thru some wires at the relay on the control board of the unit, activating it and powering the machine.So you must check 3 thi ... Broan-NuTone VX475 Bagged Central System Vacuum

I have had my Bissell Healthy Home for just over a year. I use it once or twice a week on five area rugs and two small bedrooms with wall to wall carpet. Just recently, the motor started to sound extremely loud and it smells like it's burning. The vacuum still picks up everything and all the brushes are turning. Advice? I really like this vacuum and would really like to fix it rather than replace it!

Hi,Here is a tip that I wrote about my Bissel but I bet you have the same problem and the hose is clogged...Bissell Bagless Upright Vacuum no ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v

Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

My electrolux oxygen canister cuts on and off. I have to open and close the vacuum, or take the base of the hose off and then re-insert. I have to do all these things before it will start up again. I sometimes shake the hose around, then it will come back on. If I try to dust with the dust brush (like a lamp shade or shelf) and the suction pulls against the object, the vacuum goes off for awhile. Sometimes I'll have to reset the vacuum by unplugging the electric cord. I never get to finis

Maybe you should have taken it back to that shop, it appartently isn't fixed. I would have replace that board, don't believe in modifing, you usually end up with other problems, like you have. One thing to check is maybe you have a partial clog in ... Vacuums

No suction in the walls for our Beam Heavy Duty Vacuum.

Do you have any open valves? Sometimes when vacpans are installed they are left open. Check those and then the other inlets to make sure they are not open.\015\012\015\012Also, if this unit is not newly installed, then you need to check f ... Vacuums

Kenmore Vacuum 116.35622: Need to know how to attach the board to the vacuum that is supply the power to the motor. (need the electrical diagram) email: [email protected]

... Vacuums

When plugged into electric outlet(checked power OK) the indicator icon on the top of the vacuum is not lit and the vacuum will not operate?

If the power indicator is not working, and your outlet is okay, then the problem is going to be in the cord or wiring. Carefully check the visible portion of the cord. If there are any cuts, or insulation scraped away, take the machine to an author ... Electrolux Epic 6500 Vacuum

I got as vacuum sealer at a yard sale - I don't know the brand/make/model to find instructions for it.It is electric - has a cord to plug in - white - 2 lights on front - 'seal; ;vacuum' under unit is a model # - BS-828

... Vacuums

I have a Z5930 vacuum and i want to trace an electrical fault. I need to disassemble it to get to the electrical connections and it is quite a tricky one to get in side. The machine will run and then cut out after a short time. It will then re-start in about 2-3 minutes and run normally again and so on. I was not able to give you the exact model but it is Ultra Filtration Oxygen line

... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

I bought Hoover Wind tunnel central vacuum 2 weeks ago from Costco. There are no instructions how to mount the metal canister to the garage wall. Brackets to mount to wall not supplied with the unit. How can I download the instructions ?

There is a hinged bracket for this unit which has a 5" bolt through it. It comes from CanaVac who manufactures under label. If you cannot find this large U shaped bracket on the body or in the bucket, either return to COSTO or call Canavac and explai ... Vacuums

I have an older Oreck XL vacuum that sounds like it is running twice as fast as it should. I disassembled the entire vacuum, including disconnecting the motor wires, to clean out the hair, string, and other things. When I put everything back and connected all the wires, everything appears to work, including the light. The only problem is, it sounds extremely loud like the motor is running too fast. The model number is: XL3610HH Ser. No. 3610HHXA039740-6 I do not have as electrical diagram to see

... Oreck XL Ultra Bagged Upright Vacuum

I have a nearly 9 year old Electrolux Excellio Z5228 vacuum cleaner. It has recently started cutting out during operation. I cleaned the micro filter (between bag & motor) via brush & hitting against wall & seems / looks quite clean. I washed the gore filter (output from motor to clean the exhaust air) as per instructions, then let to dry. It was very clogged but now very clean. The vacuum clearner still cuts out often. Even after a long rest (say overnight) it still won't start, then ano

... Electrolux Vacuums

Oreck vaccum when i put a new belt on, the belt rubs the side of the wall of the vacuum gets real hot and busts. is there any type of washer fitting that goes on the vacuum to hold the belt in place? i dont know i need help thank you. you can reach me at [email protected]

The belt must not be running true to the pulley. You may need a brush roll, but also check the motor to make sure it isn't moving inward after the belt is put on. ... Oreck XL Ultra Bagged Upright Vacuum

I have a central vacuum system. When I disconnect the hose from a wall outlet the central canister does not shut down dispite my turning off the vacuum at the handle of the hose. The only way I can get the system to shut down is to pull the plug at the canister. What gives? Rob

What I'm hearing is the canister(Not the Powerhead) portion of the unit is running all the time unless you unplug it. this problem could be caused by a short in one of your low voltage lines running through the house. To determine that just unplug on ... Vacuums

Vacuum stopped in middle of vacuuming our carpet. Would not startup at switch. Tried other electrical outlets wondering if this was the problem and checked breakers, but it still did not go back on.

2 guesses.... One is that you vacuumed up a pice of cord or sting that got wound up on the roller (if it's that tyme of machine, and NOW everything's completelt "loced." Cure: look at the brush roller and "unwind" the cord or string.\015\012 ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0724 seconds