Having problems with your Vacuums ?

I have a Necchi Sewing Machine Model #523 (40 years old). It operates well except for the following problem: the bobbin-winder spindle does not wind, and thus nable to fill the bobbin flange with thread. Thank you.


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Necchi Sewing Machine Model #523 (40 years old). It operates well except for the following problem: the bobbin-winder spindle does not wind, and thus nable to fill the bobbin flange with thread. Thank you.


... Vacuums

Pfaff Creative 1459. When trying to wind a bobbin, I do what I've always done, turn the small round "wheel" on the right, slide the bobbing into the little knob that keeps it in place and gently press the foot thing on the floor that should start the bobbing to winding. The bobbin does not turn at all causing a loud whirring sound and the needle goes up and down as if it were making stitches. I finally got some thread onto the bobbin but it is not smooth and looks like a spider. I really nee


... Vacuums

I have had 226R 20 years. Don't use it much. I have learned to pull slack out of top thread to start so I do that. However, sometimes, as today, it will wind the thread around the bobbin holder and I have to take time to ge it all out clean it up. Is something out of adjustment or what. Sometimes it will sew OK then all of a suden it will start to wind the thread around the bobbin holder again. So I'm confused. Do you have any ideas. Thanks


Hi wwilson63,What make is that 226R?The problem is that the thread is not threaded correctly. You must be very careful and follow directions explicitly.Once you think you have it threaded correctly, sew a few stitches and see ... Vacuums

My Brother XL4030 wont swtich from bobbin winding to sewing - bobbin winding works but when i switch to sewing just wont work


... Vacuums

Which way is the bobbin winding when put into bobbin case > It will not pick up the top thread


... Vacuums

My Janome My Excel 23x will not wind bobbins. I have disengaged the presser foot so the machine does not stitch, the motor sounds like it is working fine, but the pin the bobbin sits on is not turning. Can you please suggest any other steps I may have forgotten


... Vacuums

I was given this Kenmore Model# 385. 17324990, sewing machine, no manual came with it. I cannot figure out how to remove the bobbin to re-wind it, and how to thread it to re-wind.


... Vacuums

HI, my motorized brush barely turns.It makes a hot rubber smell. I took apart and noticed the spindle the belt turns on discolored from heat. Cleaned it, but still no turning of the brush.The vac is a hoover wind tunnel. As it moved accidentally touched the belt/ spindle and burned my hand a little. Very hot in area. Bright spark from motor noted. Was careful not to touch that part!


That means that the belt is stretched and it is slipping on the motor shaft, that is why it is hot and smells like burning rubber. You need to replace the belt. Here is the correct belt you need: ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I need a part for our Thompson PW201 mini walking foot machine. The part number is BW12041, it is the bobbin winder complete.


... Vacuums

TSC 441 JUKI NEED BOBBIN WINDER TIRE OR ORING DONT KNOW THE PART NUMBER SEWING MACHINE


... Vacuums

The washer on my bobbin winder is broken where can I get spares for my Necchi Lelia 512 sewing machine please? I am in Birmingham UK.


... Vacuums

How do I wind a bobbin. - Vacuums


At the top of the machine by the spool holder should be a post that slides back and forth. Put the spool of thread on the Holder and the bobbin on the post attach the thread and slide it one way and push on the foot pedal and that should start the pr ... Vacuums

My hoover Wind Tunnel vacuum cleaner's motor spindle keeps overheating. Because of the high temperature, it keeps burning through belts (the big, wide ones). I have taken it in to the vacuum repair shop about three times now, and the problem has never been fixed. Does anyone have any advice on how to fix this or should I just buy a new vacuum?


... Vacuums

I just bought a Coby C/D Cassette player mainly to record some cassette tapes of exercise, it destroyed the tape I had of exercise by winding around the spindle and cromped the tape which will not work not did 2 tapes that way so bummed only ones I had


Coby is one of the worst manufacturers of consumer electronics available. I very much suggest you return the unit for a full refund and buy any other brand. I recommend the second cheapest instead.\015\012farmerbear at FixYa.com ... Vacuums

Have Hoover Wind Tunnel Sel Propelled vacuum. Had to put on new drive belt. Turn on unit and drive belt slides off the drive spindle.


Look for excessive wear on the unit around the pulleys and their brackets that hold them in place. It sounds like something is just worn out and the belt is either slipping because it is not tight enough or because something is not aligned straight. ... Vacuums

I have a Singer 500 slant o matic 1961 sewing machine. I ordered a new bobbin winding spring and forgot how to put the spring back into the machine---can you describe where it goes?? thank you Sandra Scott


... Singer Vacuums

My brother (prestige 20) sewing machine's bobbin winder device is broken ! how to fix it?


... Vacuums

Hoover Self Propelled Wind Tunnel. Keeps throwing off drive belt. New belt. Starts up fine, as soon as you release and lower handle, belt comes off spindle


Hi, it sounds as though that when you release the handle, I no this puts pressure on the brush or spindle, this is causing the belt to come off. You need to remove the roller brush and check it for any thing that may have rapped around it causing it ... Vacuums

Cord winder not working


Most times you will have to replace the cord rewind. Sometimes just the cord, but usually there is a problem with thr reel contacts. But now that the spring has unwound, you will have to replace it. You will need model number rather then Red Star. ... Miele Red Star Bagged Canister Vacuum

I have a Kenmore 385.19110 model machine, and the straight and zig zag stitches work just fine, but when I follow the directions in the manual to do a satin stitch (which is use the lowest stitch length) it creates a line that isn't perfect, or uniform, and after an inch or two stops catching the bobbin underneath. Have already tried reinserting the bobbin, rethreading the machine, refilling the bobbin, changing the bobbin, cleaning the needle, changing the tension. Wondering if I just got a mac


... Vacuums

I have Necchi Lydia 544, inheretade, and don't know which way the needle is fixed! what side does the flat part of the needle face? Also, what are the two bobbin holders on behind the main body of the machine, and how do they work? And, how the hairy heck! do I thread it? finally, for now! How do I get the bobbin holder to ...a...hold the bobbin, and b...make it stay in the machine, ..well, it obviously attaches in one way only, and I cannot find that way!? Thanks, Yvonne.


Hi,Here are some websites with useful information on your machine:http://www.free-guitar-tablature.com/Lydia.html This one shows how to take the bobbin case out with pictures.http://www.youtube.com/watch?v=FbEMwLNzsG4 ... Vacuums

I was given an Auriol H13726A weather station and after 5 days of perfect functioning, now it will not find the wind station. I tried resetting the whole device, but still I have no response from the wind meter. I noticed, when changing the batteries, that the LED on the wind meter will not light up. As this was a gift, I no longer have the receipt and I don't know where the weather station was bought. Thanks for helping,


... Vacuums

My vacuum has gotten clogged by human hair on the spindle. I removed the spindle and the hair and put the spindle back into the vacuum but now the suction is very weak


... Dyson Ball DC24 Bagless Upright Vacuum

I have a Pfaff Classic Style 2025. After clearing a thread jam in the bobbin area, the machine will not sew. It works without thread, but I think the bobbin case is crooked. The bobbin opening is off to the right, not up, as it needs to be.


... Vacuums

I have a Singer Model #4562 sewing machine. I am having trouble adjusting the tension. Everytime I try and turn the knob to adjust the bobbin just gets looser. Right now it just snags and gets caught underneath the material and bunches up into a big ball. There is a lot of thread inside the bobbin case that came out of the bobbin and has to be cut out to free the material. How do I fix this mess. I am a novice at this. I have not sewn in several years and would like to sew a few quilts


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0182 seconds