Having problems with your Vacuums ?

GE MOTOR MOD#5KC46GN0050Y HOW DO YOU WIRE IT FOR FORWARD AND REVERSE ROTATION ON 120V?


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

GE MOTOR MOD#5KC46GN0050Y HOW DO YOU WIRE IT FOR FORWARD AND REVERSE ROTATION ON 120V?


... Vacuums

I have a InStyler (the rotating iron) by Tre Milano. This device is for styling hair. This is not a flat iron, but a cylinder that warms up and rotate's against a brush. It has 3 heat settings which works fine. Problem is cylinder has stopped rotating. My husband disassembled and believes the motor for the rotation has worn out? This is the question he had and mine is can it be replaced ? I have model number. . IS-1001 120v 60hz 135w. Conforms to UL STD. 89 0927-037875. Also stamped on the small


I'm repairing an Instyler right now. \012Troubleshooting, I connected a multimeter and measure the voltage where the motor is connected. When I push the button that makes spin it, I measure 12Vdc which is a correct value for that motor. Then I co ... Vacuums

Furnace blower motor wiring diagram - Franklin Machine Products MOTOR, BLOWER 120V - Sells As: 1 Each


... Franklin Machine Products MOTOR, BLOWER 120V - Sells As: 1 Each

My kirby sentria G10D 120V 50-60Hz 7A from USA. Can I use it with 220 volts, can I ammend the motor to work with 220v ? Or rapping the file with extra wires Instead of buying 220 v motor.


... Vacuums

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

Roomba 550 will not go forward, only turns and moves a few inches in reverse. I changed out the wheel motors with no results. Cleaned bumper and sensors with no results.


... iRobot Roomba 550 Vacuum

Motor wiring My Vax VS19TL motor died and I have managed to get hold of a new Vax 006 Turboforce motor which is the same size . My problem is that the original motor had two wires (black and white) which ran to the PCB switch. The new motor has three wires (black, white and yellow). I have ordered the PCB wiring loom for the 006 motor but I can't find any documentation that tells me where each wire goes. Can anyone help?


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

I have a motor for the Bissell 3750 power head with a black and brown wire, which wire is connected to what?? The old motor just had 2 black wires. There is a blue wire coming from the vacuum and blue wire coming from the light that are together, and a blue wire coming from the light and a black wire that are together. What does the blue and brown wire coming from the motor connect too? Thanks


... Bissell 3750 Lift Off Bagless Upright Vacuum

Local vacuum repair shop replaced motor in Oreck XL 2600HH and now the lights blow out immediately upon powering up the machine. I believe the wires for the lights were mis-wired to the terminal blades on the motor housing. is there a wiring diagram available to properly connect the wires to the motor housing?


Hello. if this repair just occurred return this vacuum to that repair shop as they owe you a valid repair. I agree that they caused the lights blowing out problem. They must repair this for no charge. If you work on it yourself they will blame yo ... Oreck XL2600 Vacuum

I have a dyson animal dc17 vacuum and it totally died. Now I can't figure out which wires go where when I install my new motor. (motor #: 160906G) Do you happen to know where the various color wires go or a place I can see a diagram of the motor with wires attached? I should have taken a photo of it before tearing out the old motor. I don't know where to connect the three coming out from the upright portion of the machine and the red seems to go to a switch (?) and there is a black (connected t


... Vacuums

I Have a kenmore 116.23612300 canister vacuum which will not start. I have power everywhere but nothing going to the black wire to the motor. Seems to stop at the pcb asm, #KC86WBZRZ000 . Nothing from there to the black motor wire. White wire to motor has continuity everywhere it should. Ruled out just about everything but the PC board. What does it do exactly?


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

I bought a new motor for my Riccar 8850. The new motor has 3 wires and the old one has 2. Which color wire is the ground? (or, which color wire don't I need?)


The third wire is a hot wire that goes to the headlight. ... Riccar 8850 Vacuum

How to install a new motor in a filterqueen canister vacuum the old motor was 5 wire and the new is 4 wire. Wire colors are not the same.. - No, I have not disconnected the old wires.


According to my parts house, there's a 4-wire motor for some of the filter queen models and a 5-wire model for other filter queen models.You can still purchase a 5 wire motor. Check out greatvacs dot com. They carry both 4 and 5 wire. ... Vacuums

I have a clarke bench grinder model 1002. I have a light that I would like to attach into the wiring though the grinder wiring in it's base. The light has two wires, and the grinder has a ground that is grounded to the base, a black that goes to a switch then to the motor. The white goes directly to the motor. where would I have to splice in the two wires from the light? I have a switch that I would like to put in for the light on off also.


Attach the white wire on your lamp to the white wire on the grinder.\012Attache the black wire on your lamp to the black wire on the motor side of the switch.\012This will give the lamp power any time the grinder is turned on.\012Yo ... Vacuums

Need wiring diagram for riccar supralite vacuum, replacing motor, old motor has two wires, new motor has three


... Riccar Liteweight & RSL1A RSL3 RSL4 RSL3C vacuum bags 6pk

Wiring diagram for Dyson DC05 Motor. Bought a replacement motor and wiring slightly different from original. Thermal cutout on both motors.


... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

How to install a new motor in a filterqueen canister vacuum the old motor was 5 wire and the new is 4 wire. Wire colors are not the same..


Have you disconnected old wires yet? ... Vacuums

Wiring diagram took wires off motor and do not know which goes where.There are two main from plug in one whit one black then two of same coming from light in front.On the motor ther are more terminals than wires.On diagonal corners there are black dots.Can you please help this cost 800$ and do not want to burn the motor due to crossing pos and neg.Do you have a picture or know where I can find?


... Oreck XL21 Bagged Upright Vacuum

I replaced the motor in my Oreck vacuum and it runs much faster than it used to and is very noisy. The wiring diagram that I received with the motor was very hard to read so I don't know if I wired it correctly. I also was not able to hook up the dual head lamps. Thanks, Bob


Hello Bbrote,Please visit the link provided below and find your model and then click for schematic :http://www.hescoinc.com/vacuum_cleaner_parts/oreck.html ... Vacuums

I just want a wiring diagram as the wiring is a bit messy from past repairs its had only 2 motors operating and i want to put teh 3rd motor back in.


I am not too sure of what you are working on. If you give me more information then I should be able to help. Thanks!!! ... Vacuums

G5 Kirby. Works in Neutral fine. When Drive is engaged and I push forward, the wheels do not rotate forwards, however on the pullback stroke the wheels rotate backwards. What causes this? Something is clearly in the wrong position, so a diagram showing the correct position of the part that is affected would be useful.


Hello, anjeI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would ta ... Kirby G4 Bagged Upright Vacuum

My Bissell 9200 is not even a year old and the motor which drives the dual rotating brushes at the front of machine does not rotate. Please note belts are intact and are in good condition. Motor is not functioning.


... Bissell Vacuums

G-5 Kirby self-propel works intermitently. The handle must be jiggled until it engages forward. The same for reverse. Once underway it will continue indefinitely until the need to change direction. Jiggle go forward,jiggle go in reverse. It seems as though it helps to push the handle at an angle to the left depressing the switch on the left side at the base of the vacuum head.


Sounds like a loose wire, the wire is connected to the handle, you may be able to fix this yourself but be careful you can void the warranty by doing it your self. (most people make the problem worse) remember your kirby has a lifetime warranty (limi ... Kirby Ultimate G Bagged Upright Vacuum

Oreck XL9100 Our vac motor was removed to remove a hairpin in the motor.? The tape fell off the wires. Do you have a wiring diagragm?


See diagrams ... Oreck XL Ultra Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0459 seconds