Having problems with your Vacuums ?

Phillip HD4740 rice cooker, no led comes on. but the clock window shown AM 2, any ideas on what is going on?


Answers :

The clock is controlled by an internal battery, which appears to be fine, but the actual power supply that powers the whole system has evidently failed. It sounds like this rice cooker has some major hardware issues.

How old is the unit? It may be past the point of no return, and should just be replaced but give me some more information here and I can verify.

Thanks
Tim
Yes. The control board has a faulty component.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Phillip HD4740 rice cooker, no led comes on. but the clock window shown AM 2, any ideas on what is going on?


The clock is controlled by an internal battery, which appears to be fine, but the actual power supply that powers the whole system has evidently failed. It sounds like this rice cooker has some major hardware issues.How old is the unit? ... Vacuums

O.k. this is the 3rd time I'm writing this...not even sure how many times I'm being charged.... Already aggravated and exhausted so Please, Please help me. I bought 2 Westek 1 outlet timers for our Bearded Dragons. They have to have 12 hours each of specific lighting (day and night). I get the "up" are off times and the "down" pins are on times. The problem is the Clock Isn't working.... Any ideas??? I'm about ready to throw them out the window except we're leaving early in the morning and


There is no money indication on this one. I'm speaking for free, so I hope you're asking for free.\015\012\015\012\015\012Oh yea, I already answered this question.\015\012You bought two bad timers!\015\012\015\012Sorry. ... Vacuums

I own a Sanyo 35s 3.5 Rice cooker that has stopped cooking and heating. Power is going to the unit power light comes on. We have checked to make sure that the unit was turned off before unplugging as per the instuctions. Unit was new in Feb 2010 and well taken care of. Anything we are missing here?


If you have been washing or scratching the inner pot with something sharp or harsh like a metal spoon or hard sponge it could cause that and even electric shocks. try changing the pot ... Vacuums

We have an elgin/advance 4248 alarm clock and NO manual! It had been acting strangely recently. For example: it turned itself into a 24-hour clock, the alarm didn't go off when it should have. the date setting won't change and so on. I could experiment with it if I had the instructions. But we don't. What to do?


... Vacuums

I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m


... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

How much rice to water do i use in the turbo line rice cooker i have lost my instruction booklet


... Vacuums

I have a Howard Miller Westminster Chime Mantle Clock. It has always worked fine. It stopped working and my husband took the battery out to change it and when the new battery is in it will not work. It is Model 613-=103 movt 354201J dial 272142J. The part you put the battery in almost looks too big for one double A but I can't see how two would fit. I am afraid the battery is just not in right. Can you help me with how many batteries go in this clock or if it is one what the problem could be.


... Vacuums

My husband used our Zojirushi NS-WAC18 rice cooker and lost the instructions. I would like to make rice and cannot find our instructions nor can I find instruction manual on-line. Can you help?


The Instruction Manual for the Zojirushi NS-WAC10 / NS-WAC18 Rice Cooker & Warmer is here:\012\012http://www.zojirushi ... Vacuums

Wertheim x3000 All I need to know is which way the filters go back into the Wertheim X3000. I took them out to clean them and now have no idea how the three pieces go back together. Your help would be appreciated. thanks


... Vacuums

Fein Multimaster makes more noise. I have used it a lot and, it sound like a bearing going bad. Any ideas?


... Fein Multimaster Rs - Msxe 636 - 2 Rs

My shark steam mop is not producing steam when I pump the handle - twice the mop head has blown off when I tried to pump more than the usual allotted time. Any idea what is going on?


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I am in need of an electric cord for my rice cooker. Can you help me?


Hi,Kindly tell me the Make and Model of the Rice Cooker and i would be able to Search that for you.Thanks!! ... Vacuums

I have a iRobot 4150 and have recently experiencing performance issues with the vacuum. Recently, it started stopping about a minute after you turn it on. I thought maybe the battery was the issue, but I bought a replacement. It has worked well for the past 6 months. While it's running it sounds like it is going to die, even though it is fully charged. Any ideas?


Yes, a common issue with the cleaning head module, chm. You will need to diassemble the Roomba and remove all debris from the CHM. Also take a look in its gear box. ... iRobot 4150 Roomba Vacuum

I have a Shop Vac Model#92P550A - Ultra Pro 14 Gal. 5.5 H.P. My employee tells me it would go on and off while being used and now it does not turn on at all. I am suspecting the switch could be bad but honestly have no idea whether it is the switch or the motor. Cord and plug are fine.


... Shop Vac (464-38-10) Canister Wet/Dry Vacuum

I'm doing an engine rebuild on a 1986 Mazda Familia (*** import) BFMR B6 engine 16 dohc turbo. I'have no idea where all the vacuum pipes go. It has a blow off valve and a turbo boost control fitted. The car was bought by my son, a typical teenage boy racer.


Your post needs to be reposted in the automobile repair section, this is for vacuum cleaners. ... Vacuums

We have just purchased a SX4i and the door chimes keep going off at least 10 times per day. Any ideas what we can do. Have reset etc.


... Vacuums

I bought a febreeze filter for my vacuum and i dont know where to put it according to the box it can go on it it doesnt bend and is longer then the front one any idea?


You Bought The Wrong One Maybe re-check it ... Bissell 6594 PowerForce Bagless Upright Vacuum

A large screw got sucked up the vacuum. Since then the motor,which I replaced probably only 12 months ago, sounds very "winey" and when you stand the dyson upright the front brush still keeps going round instead of stopping. Any ideas? David


Sounds like the clutch mechanism has somehow been damaged.\015\012\015\012Have a look at the following site which is a great source of info on faults, dismantling, repairing and re-assembling:\015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover problem the wheels on the bottom of my upright have come off , i have put them back on but i do not know where the metal clip should go and also the height ajuster for the wheels does not work, any ideas thanks kevin oates


The metal clip is a leaf spring and there is a slot for it, You may have to pull the cover off, may have a broken piece for the adjuster. Would help to have model number. ... Vacuums

Hi The band snapped the other day on my Vax Swift Turbo upright hoover and i got a new band from a Hoover repair centre. (Im assuming the bloke sold me the correct band). Was tight to go on. And it seemed ok. However, after switching on the band snapped immediately. Kinda burnt as well (at the point it snapped). Any ideas as to what the problem is here? The hoover is roughly 2 years old and used around 3 times per week. thanks Mike


Sounds like the brush roll is bad. Did you check the ends to make sure they turn freely? If not, replace it. ... Vacuums

My belt broke...I bought a new belt..but I do not know how to put the new on on. I took out the brush roller and put the belt around it but I have no idea how to get it to go on the part that makes it move.


Hello,\015\012Here is a link to my free online guide...\015\012\015\012http://reviews ... Kirby Ultimate G Bagged Upright Vacuum

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?


This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

I have a Dirt Devil Vision and when I put a clean canister back in place the suction at the bottom of the filter clogs up and very rarely go into the canister. Also where the air blows out of the motor, I will get particals that will blow out. I have checked where the belt is and also the suction tube. Do you have any ideas how to fix this problem?


Yes your intake hose is clogged thats the clear hose you can see it on the bottom from the back.disconnect the upper hose from your intake hose and try to push a coat hanger through with the end of the coat hangers end bent till its rounded so you do ... Dirt Devil M086700 Vision Bagless Upright Vacuum

Need manual for a Black and Decker RC5417 rice cooker


... Vacuums

How the hell do i change the now snapped band on the DC07? It has defeated 2 reasonable intelligent and practical people! ideas very welcome. The band appears to go through a slot in the bottom of the machine onto a spindle but we can not work out how to get at the spindle to put the band over it.


I can give you a general answer on most on the front edge of the bottom plate there are two screws or latches that you pull out to open and remove the plate then there will be two springs holding the beater bar in remove them and you sho ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0340 seconds