Having problems with your Vacuums ?

My baby lock model B17 keeps jamming in the bobbin area and the material gets stuck. I have trein using the fine adjustment + and - to no avail. Straight stich patern 2, stitch length 3 width set to the middle.

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My baby lock model B17 keeps jamming in the bobbin area and the material gets stuck. I have trein using the fine adjustment + and - to no avail. Straight stich patern 2, stitch length 3 width set to the middle.

... Vacuums

Singer 327 lower bobbin thread is wild and loopy after I sew...top stitch fine. Just changed to a large thread spool with the heavy remote base and crook to carry thread to machine and wonder if this changed tension (set at 4 and correctly threaded)? It had been working fine in zigzag but I also went back to reg foot and set stitch width at 0, center needle set. Thanks for your input and help. Deanna

... Singer Vacuums

I'm new to sewing. It did not come with an operating guide and I find the stitch settings really confusing I would like to know how to set it to do a basic straight stitch for a simple dress pattern. Thanks

Look for the row of straight vertical lines. This is the straight stitch. There will also be a number dial for stitch length. Use a piece of scrap to find the length of stitch you want. Make sure you have the bottom feed lever or button activated ... Vacuums

I have a Kenmore 385.19110 model machine, and the straight and zig zag stitches work just fine, but when I follow the directions in the manual to do a satin stitch (which is use the lowest stitch length) it creates a line that isn't perfect, or uniform, and after an inch or two stops catching the bobbin underneath. Have already tried reinserting the bobbin, rethreading the machine, refilling the bobbin, changing the bobbin, cleaning the needle, changing the tension. Wondering if I just got a mac

... Vacuums

What are the setting for a straight stitch on my machine?

Click this link for instruction manualhttp://www.singerco.com/uploads/download/9afcdbeb91e0cae83c6d78cb2af6d2609aa7a6f9.pdf ... SewShop.com Singer Model 6510 Scholastic Instruction Manual

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

I have a White Model 258SM sewing machine and when I have all the settings set for straight stitching, the needle bar still moves side to side. Is there something that I am doing wrong or is this normal and I just don't remember it happening before? Thank you for your assistance. If repair is needed, can you recommend someone in the Brainerd, MN area?

... Vacuums

Setting of the stictches meaning how do i set it to normal straight stitch.

You do not indicate what machine it is. Look for a lever or knob that moves the needle from left to right. With this lever/knob, position the needle in the position where it no longer zig zags.\012There may be two adjustments, one selects the size ... Vacuums

Instruction Manual for Sears Kenmore Sewing Machine Model 158 13510. Need to know how to change the setting back to the straight stitch

... Vacuums

Elna 2007 does not Zig/Zag Adjusting stitch width does move the needle but it does not move back-and-forth while sewing. I am an engineer so I can handle any task; but, I didn't want to start dissasembling without some knowledge. Look before you leap.

... Vacuums

I own a Juki MO-2404 Overlock and would like to know if it is possible to adjust the width of the stitch?

... Vacuums

How do I adjust the length and width of stitches on a babylock bl4-736d serger? I have been fiddling with it and am not getting anywhere. Thanks

... Vacuums

[email protected] can I get my machine to do normal straight stitching? I know how to dial the zigzags, etc but I forgot how to "dial" straight stitching.

You use the setting for the zig zag stitch, but set the stitch width to it's lowest setting for straight stitch.To do a basic straight stitch, you put the top dial on the black M and the bottom one on the 0. Stitch length is the dial to ... Vacuums

How can I get my machine to do normal straight stitching? I know how to dial the zigzags, etc but I forgot how to "dial" straight stitching. My machine is a White model 1888 jean machine.

You use the setting for the zig zag stitch, but set the stitch width to it's lowest setting for straight stitch.To do a basic straight stitch, you put the top dial on the black M and the bottom one on the 0. Stitch length is the di ... Vacuums

I have an old kenmore sewing machine. When i run fabric through, the bottom stitching turns into a total rats nest. Its as if the bottom is pulling a ton of thread for each stitch. The top stitching looks fine. Not sure what to do and i am a total beginner at sewing! thanks

Check the tension on the bobbin thread and ensure that the bobbin is in the right way, the thread must double back on itself. ... Vacuums

My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara

... Vacuums

Bissell will spray water when set to water rinse, but as soon as it is set to light, normal, or heavy cleaning, there is no spray. I have tried priming but to no avail. I put plain water in the solution tank to test without ay success. It is like it loses it's prime whenever you try to use a solution mix. Once you set it back to water rinse only and go through the priming steps, it is OK. Any help would be appreciated. Thanks.

Please check the following with liquid in both tanks.\012 \012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\012- Check for ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I can see the height adjuster under my Bissell pet hair eraser vacuum, but it doesn't adjust. The parts don't look like they're touching. It's been iffy since I took it out of the box. Now it doesn't adjust at all. Used only five times. Looks like I should be able to fix it myself. No local repair available. Could you help please?

Http://uk.bissell.com/images/UserGuides/3920E_508.pdf\015\012\015\012This is the pdf manual. If you look at page 12 you'll see that the bo ... Bissell Vacuums

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?

This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

My jenome 4119 will not sew after I took out thread twisted around the inside of the thread takeup mechanism. It but will not pick up bobbin thread and if it does the stitches r inches apart or none a

... Vacuums

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.

... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a

The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I got this sewing machine , can anyone tell me what this control box is used for ?. It is mounted under the table in front of the motor,It says Control Box on the front and two push button number settings with can be adjusted up or down from ( 0 to 9 ) ,Next to these settings are two toggle switches. One is marked start with on and off and the other switch is marked end with on and off. Above these switches it it says Back Track . The tag on the box says ( Type LE -BB -24 - 110 - 220, 2

Still struggling with your model number. I understand from the added comment this is a Brother sewing machine. I was hoping to find a manual that would be of assistance. Here is a couple of websites that lists available manuals for Brother sewing ... Vacuums

Hooked everything up per directions. I plugged it in to the closest electrical outlet and nothing happened. The lights did not light up, the connected wall control and sensors leds do not light up. It appears the unit doesn't have power. The electrical outlet socket is fine as everything else I plug into it works fine. I have tried every other electrical outlet available. The unit won't power on from any outlet, and all of those outlets run other things, like power tools an refrigerators

Dear Davehibshman,Firstly; dismantle the plug and replace the fuse with the same rating as the one you have just taken out. Replace the plug cover, put the plug into the socket and try again. If this doesnt work, there may be a problem wi ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0456 seconds