Having problems with your Vacuums ?

Get replacement in Scarborough, Ontario, Canada

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Get replacement in Scarborough, Ontario, Canada

... Vacuums

Hello, I have a Hoover quadraflex Powermatic central vacuum system Model # s8099-031 that requires a new replacement 35 ft hose...I have contacted Hoover and they do not know where to buy a replacement hose for this model. I live in Canada. Any idea where I can get a replacement hose for this system? Thanks kindly, Tammy

Tammy, no info re your location, so I''l try this.Your Hoover hose is shot because it was made of rubber.There are new swivel handled, tangle proof lighter hoses made of vinyl which will last much longer and can be adapted to the old Hoover hea ... Vacuums

Need a source and a number for the cannister filter -tried at the Walmart store and now am trying on line... the vacuum label says Eureka ez kleen lightweight upright 12 amp and bagless. We need to get hold of the filters for the bagless cannister sections. We need a source near Belleville Ontario Canada or on line order.

This link may help:http://www.fixya.com/search.aspx?cstm=0&_s=Eureka+ez+kleen+lightweight+upright+12+amp+and+bagless+vacuum+partsJim ... Eureka 421A EZ Kleen Bagless Stick Vacuum

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac

On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Cord replacement I need to replace a damaged cord (the reel works). How do I get the top off so I can remove the back end? Once I get it off, will I be able to change the cord, or do I need to buy the whole reel assembly? (and thanks for the help - I love this site!)

You will probably have to replace the whole reel cord. Depending on your model, on each side, there is a bar in the middle that will slide off, then the 2 halfs will come apart. They will only slide in one direction. If an older model, there are s ... Electrolux Lux 5500 Canister Vacuum

SEBO Sensors Where are the SEBO X4 sensors, I have taken this apart and not too sure where the sensors are. In particular I get Replace Roller coming up, but roller seems fine and it goes round ok if I disconnect the PCB. My unit turns on spins for 10 seconds and then brings on light C. Just replaced the motor on it about 4 months ago so not too keen to get a new one. Any help welcome.

... Sebo X4 Bagged Upright Vacuum

I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1

As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum

The top of my 500ml/0.6qt thermal vacuum flask is broken and i'm not sure if i can get a replacement as the thermos is still okay. i would be grateful to know if i can get a replacement top so i don't have to buy a new one. Thanks meryl hawkins

Hi there,\012Well yes you can purchase a separate flask for your thermal vacuum, you may purchase them from the dealer or you can please post the brand of your thermos so we can help you to find the part.Good Luck!! ... Vacuums

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a replacement switch. How do I get the cover off to get at & replace the defective metal switch? Thanx Pete Potter

Hi, you need not to do this yourself, just take it to a electronic repairer around you to take if off and replace the defective metal rather than stress yourself...Take care ... Eureka Sanitaire S661 Bagged Upright Vacuum


It helps if you have the Dyson Belt Change Tool. You can get one here:Dyson Belt Change Tool ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Miele seb 213 Powerhead is getting ac power but there is no power to the motor. The light comes on and I get 120V on the ac side of the circuit board with a meter but zero volts on the dc side.can I replace the board or do I have to replace the whole Powerhead?

... Miele SEB 213-2 Vacuum

Getting part My repair shop cannot get the part for my filter queen. It's the plug in the body of the machine that the short plug goes in from the hose. It's been bent. Can I get a replacement part?

Have you called your filter queen dealer? i used to be a rep. and we would fix problems at the office that i worked out of. hope this helps. ... Filter Queen Majestic Canister Vacuum

I have a hoover 3000 i have not used in awhile, and since I removed a large rug, I would like to use it again on my slate floor. HOWEVER, I cannot get it to pick up ANY water in the water recovery unit......it is dry, dry, dry. I have put in a new filter, cleaned the nozzle unit, the scrubber , and reconnected both the recovery unit and the water unit several times, but to no avail. I would like to get a graut attachment a well as replacement part, but since I can't get the basic unit to work, I

Have you made sure the plastic filter cover with the round hole in it that covers the filter is in place ( part # 59177096 ). This piece seems to get lost, and without it there is no pick-up. The other common problem is that the wheel assembly has be ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Where can I get a replacement glass lid for Rival crock pot model #3100/2? The one listed below is out of stock, but, even if it were, it will not fit my model. Any suggestions? "Buy-it-now-store.com" lists: CURRENTLY OUT OF STOCK, NO ETA. # Rival Crock Pot Lid Replacement Glass for 3.5 Quart Rival Slow Cookers - $5.99 Rival Crock Pot Slow Cooker Replacement Round Glass Lid Cover # Works with Rival Crock Pot Models: 3100, 3101, 3102, 3103, 3130, 3133, 3120, 3250 # Approximate total

... Vacuums

I have a samsung galaxy europa, i get repeated messages 100s of times (no exagerating) i cant get a replacement as i have had the phone unblocked, it was happening before i got it unblocked too, is there any was of getting it fixd?

Glad im not the only one i have the same problem with mine but it just seems to be o2 numbers, i have taken it back to the shop, and they i have changed the sim card about 3 times and they sent it off to samsung and they apperantly changed the handse ... Galaxy Vacuums

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef

Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

I need to purchase new blades for our 52" Jericho IV ceiling fan, Model 166315. I went to home depot in Harrisville, UT and they said that we would have to contact you and they didn't have ANY replacement fan blades in stock. HOW COULD THAT BE WHEN THEY HAVE HAMPTON BAY FANS ALL OVER THEIR LIGHTING SECTION? What kind of a business are you running when one can't get replacement parts? Our fan is making noise and I want to replace the blades. How hard can that be? By-the- way; I hope you no

... Vacuums

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?

Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

How do I get the beater brush off of the vacumm to replace the belt? The vacumm is a Shark roadstar . I can get the belt on the one end but I cannot get the brush up to put it on that end. Judy It is a Shark Roadstar EURO-PRO Model No. UV208C

... Vacuums

Belt replacement i am trying to replace the belt on my kirby g4 and i can not get the rooler off to replace the belt. if you could tell me how to do this it would be great.

Lift the light bulb housing up and you will find a latch that will rotate to release the front agitator housing and remove it from the machine. On the bottom of that housing, there are two latches that secure the bottom plate that covers the roller. ... Kirby G4 Bagged Upright Vacuum

The rotating sweeper on my Electrolux Discovery II isn't turning. Can I assume there is a belt that needs to be replaced? Also, how do I get at the sweeper unit to replace the belt? Finally, where can I find a replacement belt? Thanks!! Dewey

... Electrolux Vacuums

How do I remove the collar to replace the cord to the power bar, I have the part, cannot get the little collar off to connect the new wire, purple to white and white to black... cannot get the old wir

... Hoover Powermax S3530 Bagged Canister Vacuum

Parts replacement We have a Hoover Steam Vac that has a broken part #10 in your picture or Part # 37271035. Does this part cover the whole top section of the Vac? Is it hard to replace? Where can you get the best prices on Hoover parts? I have been on Hoovers website and they don't even recognize this Steam Vac. which is hard to believe they don't even recognize their own unit? Thanks Ray

This the hood or top cover. There some screws on the bottom as well as on the top, then it comes off. ... Vacuums

Replace belt and dyson vacuam cleaner, model dc14 I ordered a new belt and brush replacement assembly and we can't seem to understand how to get it apart to change it

If the DC14 has a brush protected aspect i.e. a switch on the front that puts the drive belt off, the drive belt would have to be replaced by a professional repairer as this can't be done at home. \015\012\015\012If the model doesn't have the b ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0690 seconds