Having problems with your Vacuums ?

I have a HeatStream Alert 3000 that has been the best little heater I've ever owned. Are they still available? Is there a close replacement available? Where can I get one? Thanks, Carl

Answers :

Hello, I have one that I am selling. Let me know if you are interested. Great condition. 60230839-780e-4a20-855d-a32920bdf15f.jpg
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a HeatStream Alert 3000 that has been the best little heater I've ever owned. Are they still available? Is there a close replacement available? Where can I get one? Thanks, Carl

Hello, I have one that I am selling. Let me know if you are interested. Great condition. ... Vacuums

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef

Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

I have a craftsman garage door opener remote control model TX2028 139.18191. The remote stopped opening or closing the garage door. I replaced the battery and tried to re-program it through the LEARN button as per the manual of the Garage 1/2 HP opener. The process has failed after several trials and the remote is still not working. Is there anything else that I can try or should I get a new remote. Thank you

... Vacuums

The top of my 500ml/0.6qt thermal vacuum flask is broken and i'm not sure if i can get a replacement as the thermos is still okay. i would be grateful to know if i can get a replacement top so i don't have to buy a new one. Thanks meryl hawkins

Hi there,\012Well yes you can purchase a separate flask for your thermal vacuum, you may purchase them from the dealer or you can please post the brand of your thermos so we can help you to find the part.Good Luck!! ... Vacuums

I have a 5 yr old Ariens snowblower ( model # 924124). I am having a problem with the deflector cable freezing. I had the deflector cable replaced a yr or 2 ago. I took the cable off and brought it in the house to thaw. When I reinstalled the cable, it worked ine except the shute does not operate in its full range of motion. I have the cable EXACTLY in its original position and routing. The shute only closes about half way. I cannot get the shute to close any lower. Any suggestions?

... Vacuums

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr

Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Dear Sir/Madam, My old faithful Hamilton Beach Mixer, now 60 years old, is still working but recently I was told by someone who looked at the motor that it needed repair or replacement. Is it still possible to get it in working condition?

If the armature shaft is worn there might be a problem, but that would be about the only one, Bushes/bearings can be replaced as can brushes. If the armature shaft is worn, a fix can be formulated but it will require some ... Vacuums

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.

Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

My brush will not turn on my Bissell 6393 upright bagless vacuum... what is wrong? The belt broke and I replaced it twice... I now have 6 more replacements but the brush still won't rotate. Do I have to get a new brush?

This type of plastic brush roll fails pretty frequently. Hair and other debis gets jammed in the end caps. The hair and debris gets hot which in turn tends to melt the plastic end caps. Remove your brush roll, hold the ends with your fingers and try ... Vacuums

Replacement globes I have been waiting for six months to get a replacement globe for my hoover windtunnel from the place of purchase. They still are unable to supply can you give me a supplier in South Australia other than Ausvac of Godfreys. Thankyou.

You might try thehooverstore.com. There may some other on-line stores that you can buy parts from. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Kenmore Progressive Canister Model # 29612992. I was replacing the sweeper bag, when I opened the lip, the plastic arms was pull out of joint and will not close. I removed the 2 screws under the lid to put back it in place but there I can't remove the plastic molding because there are still screws holding somewhere. Are there tabs instead of screws still hold the molding?

... Kenmore 25512/ 25513 Progressive Canister Vacuum

LOUD noise Turned on vacuum one day and it made a reallly loud noise like the belt had broken. So we replaced the belt correctly, and turned it on and the noise is still there it is also rattling violently. HELP PLEASE not exact same model but close enough

The armiter or fan is broken and if you get it replased it should work like new ... Hoover U5227-930 Elite Upright Vacuum

I have a Hoover U5111-900 that, every time I attempt to use it, shoots everything it should be sucking up, back out toward my feet. I have replaced the bag, pulled out lots of animal hair and such from the area behind the bag, and taken off all parts able to be removed without a screwdriver and pulled out all chunks of hair, dirt, etc. It still keeps shooting everything it should **** up out the back. Is there something I can remove to get the clog out if that's the problem? I'm scared I wil

Hello,\015\012\015\012Although I could not locate info on a U5111900, the link below shows a similiar upright and things to check for clogs. See page 12 and refer to the pages noted.\015\012\015\012 ... Vacuums

I have charged batter for over 24 hrs and still doesn't hold charge, can u replace the batteries? or do u have to get a new battery pack

You need a new battery pack. Visit www.hoover.com or fixYa.com advertiser. Other places you may check is www.batt ... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum

I have a Kirby Heritage II which normally works amazingly well, but it's not playing at all nicely today - and of course we have apartment inspections tomorrow. *dies* The belt broke today (as did the replacement belt, which I'd bought at the same time, so apparently the rubber was old), so I went over to Stark's to get some new ones - but it still won't cooperate. I've taken the head apart and put it back together several times, to be sure that everything is properly seated, but it's just not

... Kirby Heritage II Vacuum

I purchased the Shark Steam Mop less than a year ago and I have used it about 8 times and now it is not working. It will not steam. The light on the front is on and you can hear it tryng but it will not get hot and steam the water like it should. I think it needs to be replaced with a Warranty Item for free. It is still under warranty.

Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Can i get a replacement plate for my microwave oven model number MW8625W? dO THEY STILL MAKE THEM?

\012Hi,\012That is not that hard to fix and you can easily buy the parts yourself online...Here is a tip that will help you with the online buying...How to Buy ... Vacuums

I was vacuuming and noticed that the bag needed changing. the red light with the ! inside the triangle also came on. When the bag was changed, the vacuum would not restart. The red light came on. Tried the reset button but nothing happened. Tried unplugging and re-plugging in and nothing happened. Replaced all the filters and still it wouldh't start. So I brought it downstairs and tried one more time to get it to start. it worked! Is there something wrong with the vacuum cleaner? Was it overheat

It was overheated that is why it worked downstairs after cooling off. ... Miele S548 Bagged Canister Vacuum

I have a QSP Shop Vac 4 Gal and the motor has burned out. Can I get a replacement motor. These are some of the numbers on a label stuck to the motor FMC 01(F), FMC 02, 82122180, 27801 20 Thanks Carl Armstrong

... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

Change belts I have all the screws out and I still can't see how to replace the belts. Any ideas how to get the cover off? Thank you

The hooverstore page is down...schematic is here:http://www.vacsrus.com/CartGenie/pg_U8146900.asp ... Hoover U8143-900 Upright Vacuum

I own a Miele S5210 vacuum cleaner which has stopped working. It looks like the dust bag wasn't fitted properly and the machine is very dirty and the filters are completely clogged. I've cleaned it up as best I can and have replaced the filters but it still won't operate. How can I get inside the casing to clean the inner motor compartment? Thanks Tom

... Vacuums

I have replaced the filters and the bag on my Sebo X1 automatic upright but it still has doggy odor that I cannot seem to get rid of. What could be the cause and what can I do?

Hi, Yeah those things are fairly simple and easy to clean, My guess is that its in the hose.\015\012Try a weak solution of bleach and water, pour it in and let soak for 20 mins then rinse well. Dry it throughly in the sun before youe next use. ... Vacuums

Last year my wife and I bought a new Dirt Devil Reaction All Surface vaccuum cleaner to replace the older Platinum Force. After using it a couple of times the new one gets clogged with dog hair easily and shuts down. I cleaned it out completely including the hepa filter but it will not handle the dog hair. The old one never had a problem and still works. We went back to using the old vaccuum cleaner because we can not find the receipt and had not registered the new one and are stuck with a new 1

Greetings jettin_us,\015\012\015\012Normally you can contact the store you purchased the unit at, and if you paid with anything other than cash, they may be able to retrieve your receipt for you. \015\012\015\012Once you get t ... Vacuums

I have a swivel sweeper, the original series, that is about one year old and is losing power. The battery has been replaced but it still seems weaker than it used to be. The brushes do not turn as quickly and the overall pick-up is not as strong as it was when it was new. Any suggestions on how to get the power back up to what it once was?

HiThank you for your queryI think what you will find is the base of the sweeper has 4 brushes, each of these brushes are run from a cog, if you can take the base apart you will find that it has been clogged up with hair and ot ... As Seen On TV Swivel Sweeper Vacuum

The hose does not stay connected to the wand although the collar appears to be locked in place for a while. Is there a replacement part for this? Also the holder where the wand goes in has split horizontally. This appears to be one piece with the body of the unit. Is it repairable? It still holds the wand but continues to get worse.

... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1190 seconds