Having problems with your Vacuums ?

I have the Janome 6600 P. Beginning a seam the thread knotted and the machine made noise and needle would not move either up or down. I manually moved the needle using the handwheel and cut away the knotted thread. I began sewing again but instead of starting at the edge began about a half inch down, forward stitched, reversed to lock threads and problem repeated and received the message to "Stop for safety purposes". Did that. Referred to the manual, tried manual recommendation. Did not work. I


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have the Janome 6600 P. Beginning a seam the thread knotted and the machine made noise and needle would not move either up or down. I manually moved the needle using the handwheel and cut away the knotted thread. I began sewing again but instead of starting at the edge began about a half inch down, forward stitched, reversed to lock threads and problem repeated and received the message to "Stop for safety purposes". Did that. Referred to the manual, tried manual recommendation. Did not work. I


... Vacuums

I have a Pfaff 7570 ... having a problem with the upper thread making a small loop just above the fabric by the eye of the needle, just before the tip of the needle is piercing the fabric, the stitches that produced are properly formed with the right tension, but the loops get in the way sometimes and I know it never used to do this before. After reading the service manual I'm suspecting the "thread check spring" is not functioning properly. The manual gives steps how to adjust it, but it d


Http://search-pdf-books.com/pfaff-creative-7570-sewing-machine-pdf/ ... Vacuums

I have an old elna - elnita air electronic zz, i have lost the user manual and have got thread jammed under the needle plate which I can't remove. How do I remove the needle plate so that I can try and remove the thread? There are what appears to be 2 screws except they are smooth i.e. no **** or cross in the top to unscrew them.


... Vacuums

While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!


Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums

I have a Juki serger mo-634de that I am borrowing from my sister in law. She doesn't have the manual, but just got it back from the shop in good working order. I have threaded the machine, and when I manually turn the dial, it appears to stitch properly, but when I press on the pedal, nothing happens. No sound from the motor, no movement with the needles, nothing. Help! (c: Power is working, because bulb turns on.


... Vacuums

Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st


Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums

Kenmore YM-40-35 R Sewing Machine Manual (or copy) wanted. If a manual is not available, I'd be OK with instructions for threading the needle and bobbin and any additional details that an expert may have. I think the machine may be a Canadian model number, it looks old, made of metal with screwed in presser foot. Thanks v. much. Elizabeth, [email protected]


Hello,please kindly visit the site below to see the comprehensive instruction with video on how to thread and bobbin your sewing machine.http://www.wonderhowto.com/how-to-thread-mechanical-singer-sewing-machine-224245/wish you ... Vacuums

Hi. I can get my FunLock 007D serger threaded fine (as it's color coded) until I get down to the area that includes threading the needle. Can you give me some instructions that will guide me through this? I have the manual that came with the machine, but the illustration isn't clear or specific enough for me to follow. I'd sure appreciate some assistance on this. My e-mail address is: [email protected] Thanks you. Vicki Flagg


More specifically, what are having problems with when it comes to threading the needle? ... Vacuums

Needle thread tension dial - SewShop.com Singer Model 348 Instruction Manual


Here is the manualhttp://www.singerco.com/uploads/download/1317_348.pdf ... SewShop.com Singer Model 348 Instruction Manual

I do not know how to thread the machine and I also think a screw fell out by the thread and bobbin holder. I inheredited this machine from my mother and evidently she did not save the manual. Before I pay any money I want to make sure that a manual is available.


Hi,\015\012\015\012It would have been great if you would have mentioned the model number and the make of your machine so that I could have pulled out the correct manual. I am posting the entire repositary where you can find lots of manual ... Vacuums

Sears kenmore 158.321 sewing machine first broke a needle, needle was relpaced, then next needle bent, needle replaced. Now the thread wont catch in the material . it isnt sewing


Make sure you are inserting the needle correctly. The flat side goes on the left and the thread goes from right to left through the needle. ... Vacuums

My Babylock Serger Eclipse was bought around 1994 and had a looper threading tool wire to thread it when I could not get it to thread manually. I lost the tool and can't get the thread to blow through. [email protected] thanks Karen


Try one of the Serger looper threading tools listed on this Amazon.com page: http://www.amazon.com/Serger-Looper-and-Needl ... Vacuums

Singer 327 lower bobbin thread is wild and loopy after I sew...top stitch fine. Just changed to a large thread spool with the heavy remote base and crook to carry thread to machine and wonder if this changed tension (set at 4 and correctly threaded)? It had been working fine in zigzag but I also went back to reg foot and set stitch width at 0, center needle set. Thanks for your input and help. Deanna


... Singer Vacuums

I have a Singer 144w304 that I cannot get the needle thread to pick up the bobbin thread. I don't know if I am not threading the bobbin correctly out what but I had not had this problem in the past. Everything seems to be in time and set correctly but it just will not pick the bobbin thread up. What can I do?


... Singer Vacuums

I was lucky enough to get a Janome 372 very cheaply at a second-hand store but it came without the manual. A friend managed to thread it so that it works but the threading is completely counter-intuitive and I'm not sure that I'll be able to remember how to do it without a threading diagram to turn to in a pinch. Unfortunately, I can't seem to find a threading diagram online anywhere! Can anyone direct me to a site that shows this?


I would look in a site called www.Pronto.com/manualsI hope this is helpful to you . ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Kenmore sewing machine timing has gotten off. I am sewing a big upholstery project and it starting bunching thread from the bobbin. The thread is so heavy that I had to put some pressure just to get it undone. This happen a few times and then I found it wasn't sewing at all. When I evaluated without the materials in place I could see the needle would catch on the white plastic piece under the bobbin and the thread would not catch on the metal arm. It appears to be off by 1/4 - 3/8 inch.


HelloDisassemble your bobbin case which is realy quite easy, clean\015\012thoroughly with a brush and air, paying particular attention to any\015\012rust that may have formed, and any thread that may have weazeled it's\015\012way into sma ... Kenmore Vacuums

Pfaff creative 1475 cd - Broke a needle now the thing the bobbin goes in won't spin and the manual wheel doesn't twist either. I think the tip of the broken needle has it jammed. How can I take that assembly off to find and free the broken needle tip?


... Vacuums

The last time I sewed with my Necchi the tension was fine. Today when I threaded my needle, the thread felt tight in the upper tension dial. I tried re-threading the machine several times, but it didn't help. Now the parts of the tension dial are all loose and wobbbly and I have no upper tension. Doesn't matter what the dial is set on. The tension dial appears to be broken, but I don't know how that could have happend since I store it in a case.


I found this thread (no pun intended):\015\012\015\012http://www.fixya.com/support/t2902978-need_replace_upper_tension_dial\015\012 ... Vacuums

Janome sewing machine Harmony 2139 The bobbin thread is not connecting with the needle to make a stitch. We have put in a new needle. Using needle 4 tension


A common problem is if needle is in backwards. The small groove side should be toward the operator. As the needle starts back up after going clear down, a small loop should form on the side of the needle away from teh operator. The shuttle has a p ... Vacuums

The pile up of top thread


Is this in embroidery mode or sewing mode? It may be the top tension is off (in my experience knots on bottom is bobbin issue, knots on top is upper tension issue). ... Singer Futura CE-250

How do you thread an elna contessa 415. I have lost the manual and I don't seem to be able to find one. So if someone could send me a diagram of the threading instructions it would solve my problem.


... Vacuums

The thread off the needle gets caught in the hook race and the machine eventually stops. Tried different tension on the needle and the pressure adjusting lever is set at three. This is the second time I have used this new Kenmore Model 385.16231.


... Vacuums

MY NEEDLE GOES DOWN TO PICK UP BOBBIN THREAD AND SEEMS TO HIT SOMETHING SOLID. IF I TAKE THE NEEDLE OUT IT GOES ALL THE WAY DOWN. pLEASE HELP


Hi,i think the problem is with the needle bar,the alighnment has been distorted internally,i think you should re-align the needle bar in order to restore your machine back to a normal working condition.\015\012\015\012\015\012Thanks and t ... Vacuums

Sewing machine Viking emerald 183 lost manual in move. how to move needle position from side to side within foot ? Any on line manuals? TU ---gina


... Husqvarna Vacuums

Hi, I cannot seem to start my Frister Rossman 3018. I have threaded it correctly but the motor just does not seem to work and thus the needle dows not go up and down. Is it complusory to do the step of the Automatic needle threader?? Is there a video that can help me? Thanks Sejal


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0551 seconds