Having problems with your Vacuums ?

I have a Kenmore 385.19110 model machine, and the straight and zig zag stitches work just fine, but when I follow the directions in the manual to do a satin stitch (which is use the lowest stitch length) it creates a line that isn't perfect, or uniform, and after an inch or two stops catching the bobbin underneath. Have already tried reinserting the bobbin, rethreading the machine, refilling the bobbin, changing the bobbin, cleaning the needle, changing the tension. Wondering if I just got a mac

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore 385.19110 model machine, and the straight and zig zag stitches work just fine, but when I follow the directions in the manual to do a satin stitch (which is use the lowest stitch length) it creates a line that isn't perfect, or uniform, and after an inch or two stops catching the bobbin underneath. Have already tried reinserting the bobbin, rethreading the machine, refilling the bobbin, changing the bobbin, cleaning the needle, changing the tension. Wondering if I just got a mac

... Vacuums

While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!

Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums

I have an expression 2038 and the stitching has suddenly changed so that the top stitching is quite good but the underneath is loose. I have the tension on 4 and have a new straight needle and good quality thread. the underneath or bobbin thread is almost not catching.

If the bobbin thread is too loose, remove the bobbin spool AND carrier.Thread the thread through the tension clip on the holder in the normal way. Hold the thread and lift it. If the bobbin slides down, tighten the small screw 1/8 turn clockwise, u ... Vacuums

Singer 327 lower bobbin thread is wild and loopy after I sew...top stitch fine. Just changed to a large thread spool with the heavy remote base and crook to carry thread to machine and wonder if this changed tension (set at 4 and correctly threaded)? It had been working fine in zigzag but I also went back to reg foot and set stitch width at 0, center needle set. Thanks for your input and help. Deanna

... Singer Vacuums

I have Necchi Lydia 544, inheretade, and don't know which way the needle is fixed! what side does the flat part of the needle face? Also, what are the two bobbin holders on behind the main body of the machine, and how do they work? And, how the hairy heck! do I thread it? finally, for now! How do I get the bobbin holder to ...a...hold the bobbin, and b...make it stay in the machine, ..well, it obviously attaches in one way only, and I cannot find that way!? Thanks, Yvonne.

Hi,Here are some websites with useful information on your machine:http://www.free-guitar-tablature.com/Lydia.html This one shows how to take the bobbin case out with pictures.http://www.youtube.com/watch?v=FbEMwLNzsG4 ... Vacuums

I have a Continental Electric portable sewing machine and I can't get the bobbin to thread into the machine to start sewing. How do I place the bobbin and where does the thread need to go for the need to catch it?

... Continental Vacuums

Janome 6600 sewing machine. bobbin thread is gumming up underneath on a swimsuit knit type material (4 layers). Brand new machine had 1 1/2 weeks. Sometimes material goes down into the bobbin area jammed by needle. What am I doing wrong?

Make sure you're using a polyester thread (I use maxilock serger thread) then a stretch needle, and hold the tails of your thread until you get started into the seam so the fabric cannot push down into the opening on the throat plate.\015\012 ... Vacuums

My Kenmore sewing machine timing has gotten off. I am sewing a big upholstery project and it starting bunching thread from the bobbin. The thread is so heavy that I had to put some pressure just to get it undone. This happen a few times and then I found it wasn't sewing at all. When I evaluated without the materials in place I could see the needle would catch on the white plastic piece under the bobbin and the thread would not catch on the metal arm. It appears to be off by 1/4 - 3/8 inch.

HelloDisassemble your bobbin case which is realy quite easy, clean\015\012thoroughly with a brush and air, paying particular attention to any\015\012rust that may have formed, and any thread that may have weazeled it's\015\012way into sma ... Kenmore Vacuums

I have a Brother Nouvelle 1500S and it keeps looping the bottom stitch. I have re-threaded, re-inserted the bobbin, am using the recommended thread and changed the needle? It is still looping the bobbin side stitch?

... Vacuums

Please please help me! I recently bought an Empisal Celebrity 550 Sewing machine, I've used it maybe 4 times up to now. Yesterday I was sewing with it and everything was working perfectly, today, when I got home, I plugged in the sewing machine and started sewing, just to see that the bottom stitch is completely loose. It's making this loose loops instead of stitches? I didn't change a knob or anything from working with it yesterday to today, so I don't understand how it all of a sudden doesn

... Vacuums

I have a Singer Model #4562 sewing machine. I am having trouble adjusting the tension. Everytime I try and turn the knob to adjust the bobbin just gets looser. Right now it just snags and gets caught underneath the material and bunches up into a big ball. There is a lot of thread inside the bobbin case that came out of the bobbin and has to be cut out to free the material. How do I fix this mess. I am a novice at this. I have not sewn in several years and would like to sew a few quilts

... Vacuums

Have a 3 year old Pfaff Creative Vision. Has less than 14 total sewing hours on it. Has had issues in the past. Breaking needles, wouldn't stitch out designs in acceptable manner(badly distorted looking) breaking needles repeated, now it is changes stitches on its own, then went to sewing the same stitch but isn't sewing it consistantly. I have taken it back to the same professional to repair each time. Can thhis machine be repaired??? Should I trade it off and get another, this isn't my first c

It sounds like this machine has some kind of fault in it for sure. It can be repaired again, but will likely need to be repaired again after that - down the road. Personally I recommend you just get rid of this unit and go for a different model. Y ... Vacuums

I got my Mom's Kenmore sewing machine and I an trying to figure out how to get the scalloping and arrow head stitches to work. I have followed the manual and I can get all the other stiches but those two. It is a Model 1451 zig zag machine. I realize it is old, but the machine is just like new. HELP. Thank You.

... Vacuums

I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me

Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums

I have brother Star 20 electronic sewing machine, I'm having trouble with stitch...top stitck ok but underneath stitch not right...

... Vacuums

My Janome My Excel 23x will not wind bobbins. I have disengaged the presser foot so the machine does not stitch, the motor sounds like it is working fine, but the pin the bobbin sits on is not turning. Can you please suggest any other steps I may have forgotten

... Vacuums

Brand new Kenmore Sewing Machine model 385, 16782 It was sewing fine. But I changed to the zipper foot and now the bottom thread just makes a mess, even when I use the regular thread. Can't think what else has changed - I didnot rethread or touch the bobbin.

... Vacuums

Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st

Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums

Instruction Manual for Sears Kenmore Sewing Machine Model 158 13510. Need to know how to change the setting back to the straight stitch

... Vacuums

I have an Emerald 203/183 sewing machine and am having trouble changing the bobbin. I have tried to follow the instructions but to no avail. The lower thread keeps bunching up.

... Vacuums

We have a vogue stitch janome model 539 115v sewing machine. we were trying to sew but, the thread is not picking up from the bobbin. the thread keeps breaking and we are unsure what tension setting should be used for cotton cloting. please help. thanks! tom staron

... Vacuums

Water leak I just bought this steamer a few days ago, and already I am having problems, when I fill the water tank that your suppost to fill the water runs out before I even turn the machine on. I have tried using plugs to keep it from doing this just so I can shampoo my carpet, this seems to work to a point, considering the fact that there are two holes underneath close to the brushes and one just a little ways back from that location. Do you know if this is something that should have plugs or

If you just pruchased this, then it is under warranty, take it along with proof of purchase to a warranty repair shop and have them fix it. If water just runs out, then there may be a seal missing or a water line off. ... Eureka Atlantis 2595A Upright Wet/Dry Vacuum

I have a pfaff select 1530 bought aprox 2003. I would like to free motion quilt. Have bought an open toe quilting foot and have lowered the feed dogs. The quilt just doesn't move freely. It is very hard to manouvre. I have tried a friends machine to free motion quilt (not pfaff) and it is smooth and free flowing. I hasve tried changing the tension and stitch length. Can you suggest something.

... Vacuums

My sewing machine is otherwise perfect..but the stitches hv a tiny dot from the thread in the bobbin case...wat to do??

Tighten the bottom thread or loosen the top thread a little. There should be a little screw on the bobbin holder where you can adjust bottom thread tension.lp ... Vacuums

Janome sewing machine Harmony 2139 The bobbin thread is not connecting with the needle to make a stitch. We have put in a new needle. Using needle 4 tension

A common problem is if needle is in backwards. The small groove side should be toward the operator. As the needle starts back up after going clear down, a small loop should form on the side of the needle away from teh operator. The shuttle has a p ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0560 seconds