Having problems with your Vacuums ?

Was sewing on my Babylock Companion 7500 sewing machine when it started sounding like a "rod" was knocking. An alarm sounds, it stops and thread is bunched up on the under side? Got any ideas what the problem might be?

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Was sewing on my Babylock Companion 7500 sewing machine when it started sounding like a "rod" was knocking. An alarm sounds, it stops and thread is bunched up on the under side? Got any ideas what the problem might be?

... Vacuums

I have the Janome 6600 P. Beginning a seam the thread knotted and the machine made noise and needle would not move either up or down. I manually moved the needle using the handwheel and cut away the knotted thread. I began sewing again but instead of starting at the edge began about a half inch down, forward stitched, reversed to lock threads and problem repeated and received the message to "Stop for safety purposes". Did that. Referred to the manual, tried manual recommendation. Did not work. I

... Vacuums

HI I have a Necchi Super Utility sewing machine and it has suddenly stopped picking up the thread from the shuttle. I have recently been sewing some quite heavy leatherette material, could this of caused the problem and do you know how to fix it?

... Vacuums

I have an electrolux oxygen canister that's 4 yrs old and it just stop working. It just doesn't turn on and no lights display. I veryfied that the outlet works. I took it at my local Eletrolux store but they don't deal with this model. They told me that this model is made in Europe and they don't support it. Where can I take it to be looked at or do you have any ideas what the problem might be. Last time I used it it was working fine. Thanks, Rodi

... Electrolux Oxygen Z5540 Pet Lover Vacuum

My Kenmore sewing machine timing has gotten off. I am sewing a big upholstery project and it starting bunching thread from the bobbin. The thread is so heavy that I had to put some pressure just to get it undone. This happen a few times and then I found it wasn't sewing at all. When I evaluated without the materials in place I could see the needle would catch on the white plastic piece under the bobbin and the thread would not catch on the metal arm. It appears to be off by 1/4 - 3/8 inch.

HelloDisassemble your bobbin case which is realy quite easy, clean\015\012thoroughly with a brush and air, paying particular attention to any\015\012rust that may have formed, and any thread that may have weazeled it's\015\012way into sma ... Kenmore Vacuums

I want to get my XL-5000 singer sewing machine to work. It does not sew. The top thread will not pick up the bobbin thread for one thing and the other problem is that it gives me a error message saying incomplete threading.

Check if there is any thread in the bottom bobbin and next remove it and give it a good clean in its surrounding area.Oil surrounding mechanism carefully and manually push the top needle in and watch the bobbin spinning a see if it tried to pick the ... Vacuums

I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me

Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums

Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st

Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums

I have had 226R 20 years. Don't use it much. I have learned to pull slack out of top thread to start so I do that. However, sometimes, as today, it will wind the thread around the bobbin holder and I have to take time to ge it all out clean it up. Is something out of adjustment or what. Sometimes it will sew OK then all of a suden it will start to wind the thread around the bobbin holder again. So I'm confused. Do you have any ideas. Thanks

Hi wwilson63,What make is that 226R?The problem is that the thread is not threaded correctly. You must be very careful and follow directions explicitly.Once you think you have it threaded correctly, sew a few stitches and see ... Vacuums

Will sew for 2-3 inches and then slows and stops. Hand wheel very stiff. End having to remove fabric and start over turning hand wheel until it loosens and then will sew for few inches and repeat the problem.

... Vacuums

I fear the motor has failed on my Electrolux Oxygen EL6988D. Just six months after the warranty expired, I was vacuuming when it suddenly stopped. There was no blockage in the tube and it wasn't working hard or long . . . it just stopped. I looked around the Internet and it appeared that many similar Electrolux units have a fuse. I hoped my problem might just be a blown fuse, so I took the machine apart. There are two small printed circuit boards, but no fuse. There is an in-line

Hi,\015\012\015\012I don't think you need a new motor, but please stop testing the machine with live power. It's dangerous and unnecessary. Your tests indicate to me that the motor is fine and your thermal-fuse - I think this is wh ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Makita 440 Dust Extractor - Trying to rectify a problem, when i switch on an appliance plugged into the socket, it will not run. IS used to run with this plugged in, but the hoover motor runs no problem. Any ideas what might be amiss, or where i can get a wiring diagram? Thanks in Advance!

... Makita 440 Wet/Dry Vacuum

I have a Singer Model #4562 sewing machine. I am having trouble adjusting the tension. Everytime I try and turn the knob to adjust the bobbin just gets looser. Right now it just snags and gets caught underneath the material and bunches up into a big ball. There is a lot of thread inside the bobbin case that came out of the bobbin and has to be cut out to free the material. How do I fix this mess. I am a novice at this. I have not sewn in several years and would like to sew a few quilts

... Vacuums

I have a janome BCC-30 sewing machine and the upper thread has started to break and fly out of the needle while I am sewing. The problem continues even when I change the tension dial.

... Vacuums

Hi good day, I have a Kenmore Grab n Go 12.0AMPS Vacuum cleaner, Model# 116.34722402 & serial#T53601507. The vacuum is now having a problem whereby the rolling brush underneath is not spinning when the vac is on. This has caused it to stop sucking up dust. Could you please advise as to what might be the problem. Thanks in advance for your kind assistance. regards, Clarance

... Kenmore 34722 Grab-N-Go Upright Vacuum

I have a minuteman c37115-14 MPV14 vacuum. When I turn it on the brush will rotate for a second or two and then it stops. The light indicates "brush is blocked". Any idea what my problem is? TY Mark

Check your brush roll for string (from the carpet) or other debris in and or around the bearings on the ends of the brush roll. Or check your brush height. If you have the brush too low/close to the floor it drags the brush down, telling the circut b ... Vacuums

The bobbin thread is not coming up. I broke a needle and this happen. I have changed the needle twice. cleaned all the lint from the bobbin case. I believe this might be a timing problem is it possible for me to afix this?

Hi, check list:\015\012\015\0121 - Flat side of the needle is facing the back of the machine.\015\012\015\0122 - Threaded machine with the presser foot up - always.\015\012\015\0123 - Bobbin thread is feeding from ... Vacuums

It starts very briefly and then the red light flashes. It stops as if there's a problem. It is all clean and fully charged. WE were wondering whether it wasn't charging properly, just an idea. We don't know.

I have the same problem,any solution? ... iRobot Roomba 530 Robotic Vacuum

Using a borrowed Thompson Model PW-301 Mini Walking Foot Sewing Machine. The top thread will not stay in the needle. What is the problem? If we ere to buy this machine today what would be a fair price to pay?

... Vacuums

The motorhead on my Dyson DC05 stopped working. I bought a replacement motorhead but it also does not work. Any ideas as to what the problem may be?

It could be the hose or the pipe electrics that are not working have you got any lights on the head at all ... Vacuums

I have a light ballast that stopped working. The lights around this one bulb still work but changing the light bulb did not fix the problem. Any idea what is going on here?

The ballast is like a fuse and the ballast is blown .\015\012you will need to replace the ballast as it will let current thru for some bulbs but not enough to light them all up.\015\012also if you use old bulbs that are alomst blown and n ... Vacuums

Hi i have a babylock proline bl4838df overlocker...the stitch is perfect but as i sew the machine slows down to stop completely.....is this a motor problem or can i fix it myself...thank you for your time....simone

... Vacuums

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?

Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have an easy flo vacuum model # 199C and it won't shut off. It started out as an intermitent problem but now will not shut off when the hose is unplugged, nor when the off/on switch on the main unit is shut off. the only way to get the motor to stop running is to unplug the unit. Any ideas?

Just had this same problem. I unplugged the low voltage signal wires and the vacuum stayed on. Thus eliminating the possibility of the signal wires shorting out somewhere. I'm not really sure which wire(s) were causing the problem. But when I disasse ... Easy Flo EF1500 Vacuum

HI, I have a Kenmore 25813 and it seems like there is an intermittent short. When I have the extension wand on and the power floor attachment on, when it rotate the wand the light cuts out and so does the power floor attachment, when I twist it back it comes on again. I don't have this problem if I remove the wand and just use the crevice tool with the hose. Any idea where the short might be and can I fix it myself? Thanks. Gary

This is common you may have a short in the contacts from the handle to the wand or a break in the cord that goes into the powerhead ... Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0527 seconds