Having problems with your Vacuums ?
Requiring parts for homelite engine model UP154
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Requiring parts for homelite engine model UP154
I have a Thermos labeled King Seeley Thermos Co. Model no. 2466 I require a new Screw top stopper part no. 764 it also has the number A84 at the bottom, is it possible to purchase one Thank you Jim Raine
The part can be found at amazon.. take a look here Amazon com thermos Screw top stopper. I hope this was helpful. Cheers ... Vacuums
Where can i buy parts for the model C151D vacuum. any place i checked does not have that model of electrolux listed. i need the power wand attachment. i ordered one that looked like it from sears parts direct but it wasn't the proper one and they do not list the model C151D
Any Aerus Electrolux store. For the one nearest you, check the below link and follow the directions. Keep in mind that if it's too far away, they do ship. If you're close enough, they do deliver.\015\012This model is not the same company tha ... Electrolux UltraLux 2000 Bagged Canister Vacuum
We are unable to find a replacement part that the filter attaches to in the dirt cup on our Eureka Boss Pro Model 411. This part seals the top of the dirt cup and holds the filter in place. What is the part name or model number for the replacement?
I just called Eureka (1-800-282-2886) and asked for the dust cover lid. It was part number 61538-1. They said they could ship it to me or I could call one of the authorized service centers nearby to see if they had one. I wasn't in a hurry and the ... Eureka 411A Upright Vacuum
SEARS KENMORE CANISTER VACCUM, Model No. 107-23050, Volts 120AC, Type AV, Hertz 60, Amps 11: This is a small model vaccum with an on/off switch on the canister. The on/off switch has gone and the vaccum can only be used by plugging and unplugging it. I am looking for the replacement on/off switch part but Sears Kenmore has no listing for this vaccum or parts. I can't recall just how long ago it was purchased but could be 10 years (or more). As this model is perfect for the application neede
Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless
Get over it and buy a new one!!! ... Vacuums
I'm trying to find a part number for the motor on a 113296200c, craftsman wet/dry vacuum. Sears could only provide part number 09 113826404 for the model number 113296250c. I have found motors with the model number 826404 on ebay, however no one can confirm if this is compatible. Can anyone help me out here?
... Craftsman 17026 Wet/Dry Vacuum
The top blades of the dasher of my Rival 4-quart electric ice cream maker (model #8704) are broken. I need to replace this part. I couldn't find this model on the website or any site from which I could order this part. Can you help me?
Hello,The part for your ice cream maker is not available any where online. The best thing you can do is to contact the manufacturer and ask them where you can get the part. They might have dealers who sell the parts.You can ca ... Vacuums
Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.
On my Eureka Model 1759A (from mid-1980s), the plastic catch that holds the two parts of the metal body together has broken. I would like to replace the part of the catch that attaches to the top (the part with the lip on it), but I can't find the part online ... or even a drawing. Where can I get this part ? ? ? HELP ! ! !
This latch is riveted to the body. If you are lucky you may find an old Eureka warranty/ repair center with one on the shelf, or another canister for parts. That will be your best hope. ... Vacuums
Parts Hi I have the Eurkea steam cleaner model 2450 and was wondering how do you take the front part off where you can see the water sucking up from carpet so this can be cleaned. Also I think the spring in the part that holds the water has come off another part is this able to be fixed or can I just purchase a new water holding tank and if so where? Thanks
Click this link for spare partshttp://www.vacpartswarehouse.com/Eureka-2450-extractor-s/1802.htm ... Vacuums
I have a Kenmore Progressive model 116.22812204 purchased 2003. The swivel (part nuumber 8195133) that attaches the extension wand to the power mate attachment snapped, so I can't keep the parts connected. I can order a replacement part on-line, but I don't know how to replace it - is it difficult to take apart the power-mate and replace this part? Do you have instructions on how to do it? Thanks!
... Kenmore Vacuums
Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest
I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum
Kenmore Model 116.33922 upright - I need a hose unit - Part # KC84PCDBZV07 - Sears parts told me it was not available to contact the Manufacturer - Kenmore (per them) - Their site sends me to Sears Parts! Where can I find this part?
... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
HI, I'm trying to find a part for a Sharp upright vacuum. Its the back part of the handle where the cord is stored. I have taken it off but can't find any part # on it. The model number for the vacuum is EC12TWT4. I was thinking that if I could find a free owner's manual, that would give me the part # and then I could look for it on the net.
Any vacuum repair shop should be able to get it ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum
I require "Hose Assembly complete" for LG Vacuum Cleaner Model V-KC 402CTU
Needing part #600-6083 for Bissell 3-way Vac model #3037. Can't find part on any website. Is this part still available?
Hi there it's SmartAlec from NelsonVacuums.com.au here. If you are in Australia i can help you with any parts for Bissell machines. I would really need to get some extra de ... Bissell Vacuums
Trying to find replacement part for a Bissell Power Steamer Deluxe Model 1631-1, Part Grip and Trigger Assembly Part No. 016-4181
Http://www.bettervac.com/bissell-016-4181-handle-assembly-for-big-green-machine.aspHopefully this helps. ... Bissell Vacuums
We are using a nakamichi music system, model no is SS8, we want new part of the system part no is 0B50328B, description - power transformer D143EP R55 kindly let us know from where we can get this part available.
We need nakamichi soundspace 8 main transfromer output voltage ... Vacuums
Hi, I have a Kenmore Whispertone canister vacuum that I purchased in 2007. The model # is 116.22271503C, which seems to confuse the parts people. I need to buy a new powerhead & a few months ago was given a price of $75, but now Sears Canada tells me the part # is 20 116KC5OXBZRZUO1 described as Power Mate Assembly for $192.99. I thought the Power Mate was the small powerhead for stairs, upholstery, etc. Have they located the wrong part for me, or is this really what it costs?? Thanks in advance
Yes, powerheads are quite expensive. That sounds about right.\015\012You can check Ebay for better prices, but check the shipping rates before ordering. ... Kenmore Whispertone 23312 Bagged Canister Vacuum
I have a Bissell Model 8905 Carpet Cleaner. I was going to replace the belts because the pump belt broke, but when I turned the machine over, a small piece fell out. It looks like a tensioner arm because it has a small round part at each end on opposite sides of an arm that has an offset or "dogleg" in it. I am looking for an exploded parts diagram to determine what the part is and where it came from.
... Bissell 8910 ProHeat Clear View Upright Vacuum
Need part for stand of Hamilton Beach Scovill Model 44 Mixer. Part is locking rocker tab that hold mixer in place on stand or press to remove mixer head from stand. Don't need spring or pivot pin, just rocker tab. Don't have part number.
Looking for a part for a deli meat slicer model:FS04. The brand name is Savoureux Pro Line. I have not been able to get an address for this company, but I do have a parts list. The part I need is a worm gear. Thank You
Hi, did you ever get the worm gear? I need one for the same machine. ... Vacuums
Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? Thanks
Hi\015\012\015\012To remove the broken part from the latch use a small screwdriver to release the tabs on the latch on the connector. When latches are released the latch assembly and the plate will slide out of the connector. When the pla ... Kenmore Vacuums
I have an old Progressive vacuum cleaner that says "Hepa Filter" and "Whisper Belt". Not sure what the model # is. The problem is that the vacuum part itself (the part that touches the floor and rolls over) has ejected its filter that we can see through the little window- it just came out under the rollers under the device... we cannot see how to re-insert this piece of filter which looks like a kind of round, flat grey foam/fabric and clearly goes inside- (top of the part that touches the flo
Check this procedure:\015\012\015\012Unplug the appliance that you will be \015\012changing the filter in.\015\012\011\011\011\011\011\011\011\015\012\015\012\011\011\011\011\011\011\011\011\015\ ... Kenmore 23313 Whispertone Bagged Canister Vacuum