Having problems with your Vacuums ?

I have their Margarita OASIS model MOS-400 series. I got it for Christmas two years ago and now the blade in the ice tray is dull and even small bits of ice will not get shaved. Is there a way to replace the part or to sharpen the blade.


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have their Margarita OASIS model MOS-400 series. I got it for Christmas two years ago and now the blade in the ice tray is dull and even small bits of ice will not get shaved. Is there a way to replace the part or to sharpen the blade.


... Vacuums

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

Parts replacement We have a Hoover Steam Vac that has a broken part #10 in your picture or Part # 37271035. Does this part cover the whole top section of the Vac? Is it hard to replace? Where can you get the best prices on Hoover parts? I have been on Hoovers website and they don't even recognize this Steam Vac. which is hard to believe they don't even recognize their own unit? Thanks Ray


This the hood or top cover. There some screws on the bottom as well as on the top, then it comes off. ... Vacuums

I am looking for a specific part for a Nostalgia Electrics RIC-100 portable ice maker and I am finding it very hard to find what I am looking for if I could get some help that would be great. The part I am looking for is the the tray that the ice maker puts the water into and holds to freeze the water to make the ice before it is dumped into the holding tray for the rest of the ice


... Vacuums

I'm using Miele Medivac vacuum and I just sucked in a small plastic eye drop container by accident(I sometimes take off the brush part to **** in 'small enough' articles). And it is jammed in the part where the plastic hose connector bends. I think I can take it out if I can just disconnect the long necked plastic hose connector that connects the metal wand part and the hose part. Is it designed to be disconnected or should I not even try it?


I love the fact that the filter bleeped out s.u.c.k ha ha! ... Vacuums

On my Eureka Model 1759A (from mid-1980s), the plastic catch that holds the two parts of the metal body together has broken. I would like to replace the part of the catch that attaches to the top (the part with the lip on it), but I can't find the part online ... or even a drawing. Where can I get this part ? ? ? HELP ! ! !


This latch is riveted to the body. If you are lucky you may find an old Eureka warranty/ repair center with one on the shelf, or another canister for parts. That will be your best hope. ... Vacuums

During re-assembly of my conair (model HC91RS) i noticed that my two blades do not line back up. The big blade sits evenly in it's space but the small blade is tilted slightly to one side. Is there any other means of aligning these two blades?


... Vacuums

My Kirby shampooer - G4 - hardly used any water from the tank and no suds at all. Pet hair did blow out of the small slotted holes in the tray as I moved the shampooer back and forth, but the carpet was basically dry. I did vacuum before shampooing, so the brush part seemed to work great during shampooing, but no water! The small screen was stuck in the crook of the hose that attached to the tank so I did get that out and put it on the small hole on the tank, but it didn't make any difference. I


Few things:Make sure the sponge and the valve under the sponge (water tank) is clean.Make sure you follow the instructions (f you do not have the manual you can find one ... Kirby Ultimate G Bagged Upright Vacuum

I need to purchase new blades for our 52" Jericho IV ceiling fan, Model 166315. I went to home depot in Harrisville, UT and they said that we would have to contact you and they didn't have ANY replacement fan blades in stock. HOW COULD THAT BE WHEN THEY HAVE HAMPTON BAY FANS ALL OVER THEIR LIGHTING SECTION? What kind of a business are you running when one can't get replacement parts? Our fan is making noise and I want to replace the blades. How hard can that be? By-the- way; I hope you no


... Vacuums

I have a lawn sprinkler system that has a main inlet valve that opens when the sprinkler is run. This inlet valve failed after a recent long freeze when water retained in the valve became ice and then expanded. Questions: 1. Can I replace just the plastic parts that broke or do I have to replace the total valve? The valve is made by FEBCO,CA and the following is written on the valve: 4010387; 765-PUB; B 6412 and 150 MWWP. 2. Where can I get the valve or the parts? My zip code is 77479 and I ca


Yes you can, take the piece into home depot they can help with it. usually you can replace the total valve as awhole , its easier to do it this way, and still cost effective :) \015\012\015\012press add a comment in upper right corner if ... Vacuums

My Dyson DC17 has lost suction on the wand and is not picking up dirt as it should. I have taken the small part at bottom of the machine off to see if there is a blockage--none that I can see. The flexible tube on wand is very tight and won't extend very much. Dyson sent me a new cyclonic part in April but the machine still doesn't seem to be working properly. My serial number is 260-us-d11545. Is there somewhere I can take my Dyson to get it fixed. I'm very frustrated with it. Thank you.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

The top blades of the dasher of my Rival 4-quart electric ice cream maker (model #8704) are broken. I need to replace this part. I couldn't find this model on the website or any site from which I could order this part. Can you help me?


Hello,The part for your ice cream maker is not available any where online. The best thing you can do is to contact the manufacturer and ask them where you can get the part. They might have dealers who sell the parts.You can ca ... Vacuums

My Hoover Wind tunnel has even a cheaper on/off switch and now, you can't buy a new one. I used to go to their website which had a wonderful diagram of the 'guts' but now the only parts are the obvious ones, belts, filters etc....I have to vacuum twice a day and I should be the test person cause its on and off on and off, but now for a vacuum I purchased 3 years ago for over 200 bucks and I can't fix it myself really makes me made or do you know where I can get this part? help? if not, I will ne


Have you tried going to appliancezone.com? I go there when I need parts... ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

We've changed the bag and we are still not getting good pick up. It seems to leave small paritcles and bits of fuzz.


I have a wind tunnel and it is so "STOPPED" up that it won't pick up anything ,. How do i un stop it? ... Hoover Company Wind Tunnel U53019 Upright Vacuum

I am trying to find somewhere to get spare parts (in particular the small detail brush) for this two-year-old steam cleaner. It appears that Domotec no longer have a UK distributor but I think they do still exist somewhere in Europe.


Domotec does not exists anymore , however you can buy from www.espares.co.uk : Vax Steamer Nylon Brush (ES956244) which is similar to the one supplied with Domotec steam cleaner. ... Vacuums

The motor just went out on my 2 year old vacuum with light usage (hardwood floors in a very small house.) The Sears repairpeople are estimating ~ $130 to fix (this includes parts & labor). I'm wondering if it's worth investing $130 into something i've spent $350 on only 2 years ago. Shouldn't these machines last longer ? Is there something I could do to get them repair free as it seems the motor must have been faulty to only have lasted 2 years. Thoughts ?


Aye, get a dyson, if its out of warranty there's not much u can do bout it :( ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n


From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?


First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

I have a dyson dc07 original that i bought used. Last owner was obviously a pet owner and the machine smells too bad to even turn on in the house...can I clean the canister with water? What other parts can get wet or is there a better way to remove the odor?


Put some vac freshner in the canister put the vac out side if its fine plug in and switch on leave runing for around 10 minutes that should solve the odour ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Suction hose I can't get the suction hose to work...and I have cleaned it out to make sure it isn't plugged. There is a small amount of suction just not enought to pick anything up.....the floor part works great...what could be the problem


I would first double check the hose, remove it and drop a marble through it to be sure. make sure the bag is new and also check the filter underneath the bag if it is clogged it could cut the suction. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

LOSING SUCTION IT APPEARS WHEN IN UPRIGHT POSITION, ALTHOUGH SUCKING (TO SOME DEGREE) IT THROWS BACK SMALL PIECES TO THE BACK OF THE VACUUM OPNTO THE CARPET BEHIND, AND THE CONTAINER HOLDING THE STUFF ISNT WHIRLING AROUND THE CONTAINER. I WONDER IF THE PASSAGE TO THE WIND TUNNEL IS BLOCKED, AND OF COURSE THAT IS THE PART I CANNOT GET TO, AS IT NEEDS A SPECIAL TOOL TO UNSCREW THE BACK OF THE VACUUM.


Is brushes moving, if so it is clogged , usually takes a star bit to take apart to clean ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Part need I need the small nozzel for grabing corner dust , which has brush too . Will you please let me know where can i get it ?


... Bosch BSG81313UC Premium Bagged Canister Vacuum

Hi I have a panasonic SD251 bread maker. The circlip for the bread pan has broken and I have not been able to purchase a circlip small enough to fix it. Any suggestions on how to get a replacement circlip would be greatly appreciated. Even the size of the circlip required would be helpful


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0667 seconds