Having problems with your Vacuums ?

I have an old Janome sewing machine and when I plug it in at the power point and turn it on it sews without putting your foot on the pedal Can you help


Answers :

I have to same problem as tony
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an old Janome sewing machine and when I plug it in at the power point and turn it on it sews without putting your foot on the pedal Can you help


I have to same problem as tony ... Vacuums

I was putting some bedding in a bag for storage and decided to ''**** it down with my dyson hose to fit it in a smaller space. My dyson quit working and now it will not turn on can you please help...??? I know I didn't **** anything up but I can't live without a vacuum!! I have tried the brush reset button but can't find another reset...


There is no other reset. The Dyson will cut out if it gets too hot, but resets itself when it cools. In doing the job you describe, I doubt that you have operated it long enough to cause overheating, or to do any other damage. I suspect the problem i ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

The presser foot is stuck in the down position on my sewing machine. The lever goes up and down but the foot will not move. Help! I have an old Kenmore 22 sewing machine. Probably got it around 1990. The model number is 385.17622.


If you open the left end of the machine .. look inside above the needle and to the back .. you will see a pivot bolt that has either come loose, broken off or fallen out .. replacing that bolt should fix the problem .. ... Vacuums

My Kenmore sewing machine timing has gotten off. I am sewing a big upholstery project and it starting bunching thread from the bobbin. The thread is so heavy that I had to put some pressure just to get it undone. This happen a few times and then I found it wasn't sewing at all. When I evaluated without the materials in place I could see the needle would catch on the white plastic piece under the bobbin and the thread would not catch on the metal arm. It appears to be off by 1/4 - 3/8 inch.


HelloDisassemble your bobbin case which is realy quite easy, clean\015\012thoroughly with a brush and air, paying particular attention to any\015\012rust that may have formed, and any thread that may have weazeled it's\015\012way into sma ... Kenmore Vacuums

Motor wont turn on.I checked the switch and I think it is working.motor turns on if a put direct power to it.'but it smokes at the brushes. can you help?


This sounds like either the belt isn`t on right or the brush is not slotted in the vacuum right remove the plastic or metal cover from the bottom and check by inspecting the belts ability to easly turn the brush rod check with your hands DO NOT turn ... Kirby G4 Bagged Upright Vacuum

Roomba Discovery My Roomba turns on and moves but the brushes won't turn. Someone told me that I had forgotten to put in the yellow and black end bearings, but I did. Help, I miss my Roomba I have a Roomba 530, I have had it for 2 weeks and really loved it. I have followed all the cleaning instructions etc.. Then the Roomba wanted it's brushes cleaning "please clean Roombas brushes" So thinking that something was stuck I removed and cleaned the brushes, (yellow tabs on and in place by the way)


I read somewhere that you need to clear the software in case there is a glitch. To do this, take the battery out and then, simultaneously hold down the "spot" and "clean" buttons for 30 seconds. Replace battery. This has worked for my Discovery model ... Roomba Robotic Floor Bagless Vacuum

I have a Bernina 930 sewing machine. I read the advice from "dogdanes" about the basting unit seizing up and I think this is my problem. It has happened once before, and I NEVER use the thing, so I think it's frozen. My flywheel won't turn. Can you help me fix this? I have a sewing business and can't afford to have my Bernie in the shop for weeks. Thanks. Maripat


Hi marjpatv,With your Bernina 930 sewing machine where the flywheel won't turn and seems like it's frozen, sounds like it needs some oiling. You may want to try having it oiled first since it could be a possible cause of this issue. You m ... Vacuums

Roomba Discovery My Roomba turns on and moves but the brushes won't turn. Someone told me that I had forgotten to put in the yellow and black end bearings, but I did. Help, I miss my Roomba


The plastic gears that drive the sweep brushes strip out easily on\015\012these. You can get the company to repair it for you but they make\015\012it a big hassle. I opted to buy the gear set on EBAY and replace\015\012them myself. ... Roomba Robotic Floor Bagless Vacuum

In trying to repair foot pedal on my Hoover Windtunnel self propelled bagged vacuum, I got carried away and took apart most of the unit and I am still not able to get to the release..... I need help fixing the release lever AND then advise as to how to put the sweeper back together....Help!


This video should help you ... Hoover Vacuums

I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!


Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum

Roomba Discovery Roomba is fully charged and cleaned with sensor wiped clean. When turned on it it sounds normal and commences to go, but it then acts like it is putting on the breaks, spins, tries to go and manages a short distance and breaks again, just not making any progress because it keeps breaking after a foot or so and turns and tries again. Sometimes is gets so stuck from moving forward at all, like it is stuck in one spot just trying to go while seemingly surrounded by barriers. Somet


I had the same back-up, turn, move forward a couple inches, backup-up, etc. problem. Try cleaning/cutting the hair, etc. out from around the brushes, as well as around the ends of the brushes. Also, try a Q-tip to clean out the four pair of sensors ... Roomba Robotic Floor Bagless Vacuum

Need to open rotating brush part of vacumm as motor functioning but roller not turning...perhaps belt broken put need to get into ..inside brush box ...Need help need instruction with diagrams Thanks for help Robert


... Panasonic MC-V9638 Bagged Canister Vacuum

I have a 5260D Baby Lock Serger, which I had tuned up a year ago. I haven't used it very much since. When I took it in, and again now, it sews fine for awhile, then starts slowing down until it is barely sewing, even with the foot all the way down. The hand wheel seems very tight. - it doesn't turn freely, but takes a some push, like it is resisting a bit. Any idea what could cause this slow down and the tight hand wheel? I appreciate any ideas. Thank you. Maura


Hi,Since you say that you didn't use it for many years then does it make noise?If so it need oiling on its parts.oil orifice and point of contact.Please do rate the solution if the issue is resolved or post a comme ... Vacuums

It's been awhile since I have used my shampoo system on my Ultimate G series Kirby. Well, as instructed I took it apart and cleaned it. Now I can?t figure out where to put the ?screen cap? and ?sponge filter?. I have my manual in front of me and the only place it shows the filter and sponge (page 35 in the manual) is when it?s been taken apart to clean. It doesn?t show where to put it back. I don?t know what I would do without all the pictures in the Kirby manual. HELP! Thanx. Visual Kirby Vacuu


Hello,\015\012The littlew round screen goes in the hole where the hose attaches to the tank. The round foam filter goes up in the hole underneath the on/off valve for the foam. Here is a guide if you need any more help...\015\012\01 ... Kirby G6 Bagged Upright Vacuum

We have a Eureka Chinese p.o.s, model 6831. The brush roller won't turn, appears to be plugged with cat hair dang long hair cat. I cannot figure out how to remove the cover without breaking it after removing the screws, there is a u shaped collar on the tube in the way. Can anybody help?


There are a couple of tabs on both sides of the top housing that need to be unlocked by using a flat screw driver, then the top will come off. The u shaped collar on the tube will then give way to take the roller brush out to clean. ... Vacuums

Turbin hey its me Lisa I took the turbin apart and know where the wheels (gears) go but they have this little bearing or what ever it is its round and has a whole thru sent can't figure out how it goes to put it back together. the thing turns really good now after I soaked it HELP


You should have it all back together now. Hope it is running ok. \015\012Lauren(reddevil6) ... Hoover F7220900 SteamVac V2 Upright Vacuum

I was given a Brother Pacesetter XL795 sewing machine without a manual. The machine isn't working right and needs an adjustment. Is there a source where I can obtain a manual for free before I spend money to buy one? Thanks very much for your help.


... Vacuums

Bissell will spray water when set to water rinse, but as soon as it is set to light, normal, or heavy cleaning, there is no spray. I have tried priming but to no avail. I put plain water in the solution tank to test without ay success. It is like it loses it's prime whenever you try to use a solution mix. Once you set it back to water rinse only and go through the priming steps, it is OK. Any help would be appreciated. Thanks.


Please check the following with liquid in both tanks.\012 \012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\012- Check for ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My bonjour cookie factory came without instructions and I need help figuring out how to put it together for use.


... Vacuums

Singer 327 lower bobbin thread is wild and loopy after I sew...top stitch fine. Just changed to a large thread spool with the heavy remote base and crook to carry thread to machine and wonder if this changed tension (set at 4 and correctly threaded)? It had been working fine in zigzag but I also went back to reg foot and set stitch width at 0, center needle set. Thanks for your input and help. Deanna


... Singer Vacuums

Hi. I have Dyson dc08 hepq+. Thet problem is its not having suction .I checked inside the pipe and foot , ery thing is fine. And if i take the whole dirtbin out ...machine workes fine. when i put ery thing back ....as soon as i start it , after 2 second machine change its voice...and loos suction. I think its just happen because ...the saftey yellow valve inside the machine turns up because the dirt drum is blocked inside some where. Any suggstion ...what can i do with it. I m tahnkful in avance


Hi its Darran at Dyson.From your description of the problem, it sounds as though the bin inner is missing. To confirm this, if you remove the cyclone and bin from the machine, then separate the 2 pieces as if you were going to empty it, w ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum

My kenmore sewing machine (Model #385.11803) isn't picking up the bobbin thread. Bobbin thread case isn't turning. HELP!


... Vacuums

I took the trap(or whatever it's called)off the bottom right corner to check for an obstruction as my hose was collapsing when using the attachments. Put it back on(perhaps wrong)and now when the vacuum is turned on, dust blows out the front and there is NO suction! HELP!


Now you have a dyson leaf blower! not funny huh? Ok, just slow down and recheck your connections. Sounds like the motor is running backwards or you are hook up to the discharge. ck for baffles that block off the vacuum to the roller part when at ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hi i have a Globe Electronic 390 Sewing machine and im looking for a manual for one to help me be able to put a new needle in it, thanks


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0882 seconds