Having problems with your Vacuums ?

Hunter Fan Mod 21617-001, wire colors Black with white stripe/ Pink/Yellow/Red/Gray/Black/White. This has a floresent light, no chains or switches. The Pink serves the light. Note the wires are not labeled but I assume go to different speeds on the fan. Attempting to utilize the "Universal Remote" Mod 27185 with no joy.


Answers :

Red and white are twisted together,or however you combine wires.I use plastic wirenuts.Always twist clockwise as the wirenuts are most effective that way and the wires will stay together better.Black/white,yellow,and gray are the speeds yes,and the fan wires go to the receiver wires.It sounds like you do not have the receiver?If it isn't already built in,it should be small enough to fit within the smallest part of the fan base.The remote is the transmitter.Here is a link to show you the wiring.Red&white twist together for house power.Black for house ground.It also shows a THIN WHITE wire for the antenna.It is not necessary to hang it outside of the casing.You should make it spread out around the inside in a full circle,that should be fine.Just not wrapped tightly around the motor,loosely is better.It does show the antenna wire hanging out in the diagram.You can do that also,just make sure it isn't hit by the fan,and it will not cause a fire if pinched by the plate.If you do have all the wires connected,it shows that the dip switches on the receiver must match.Make sure the remote has the battery removed when changing these.When they are correct,there is no way to tell what the fan is set to and it could start moving.The dip switches are equivelant to radio stations.If you want 101.9FM,but it is set to 101.1FM,it won't come in.When the switches match,you are tuned in and hear 101.9FM.If you need more help,just comment here and I will get an autolink to your post and reply ASAP.Good luck,Greg The link looks universal for Hunter fans,all wired the same.
\015\012
\015\012http://www.hunterfanhq.com/tools/sales/hunter/preseason/images/owners/41597.pdf
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hunter Fan Mod 21617-001, wire colors Black with white stripe/ Pink/Yellow/Red/Gray/Black/White. This has a floresent light, no chains or switches. The Pink serves the light. Note the wires are not labeled but I assume go to different speeds on the fan. Attempting to utilize the "Universal Remote" Mod 27185 with no joy.


Red and white are twisted together,or however you combine wires.I use plastic wirenuts.Always twist clockwise as the wirenuts are most effective that way and the wires will stay together better.Black/white,yellow,and gray are the speeds yes,and the f ... Vacuums

My electrolux stick vac EL 1000 suddenly doesn't even light up to show it's charging! Is it a battery? A wire? As I try different outlets it will light up momentarily and then go out.... What do you think?


Had the same problem with 3 of my vacuums, tried using my rc charger and it fixed the problem. ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

I have a clarke bench grinder model 1002. I have a light that I would like to attach into the wiring though the grinder wiring in it's base. The light has two wires, and the grinder has a ground that is grounded to the base, a black that goes to a switch then to the motor. The white goes directly to the motor. where would I have to splice in the two wires from the light? I have a switch that I would like to put in for the light on off also.


Attach the white wire on your lamp to the white wire on the grinder.\012Attache the black wire on your lamp to the black wire on the motor side of the switch.\012This will give the lamp power any time the grinder is turned on.\012Yo ... Vacuums

Confusion and embarrasement have caused me to appeal for expert advice. I need to add a second flourescent light fitting in the loft. I recently added one from the existing wiring circuit via junction box and pull chord switch and it works fine. I have wired in the second light and now neither of them work. I have replaced the starter (as I had a faulty one in the first light. But i annot get them to work. I have installed a second junction box for the second light and wired all like terminals


... Vacuums

I have an old Friedland door chime (approx 30 years old). It has 5 terminal screws to connect wires. They are labeled 0-4. I removed the chime during remodeling and would really like to reuse it. I did not label the wires and where they connect when I removed it. I can't figure out how to wire it. I contacted Friedman and they were of no help... didn't have information on chimes that old. Can you help with how to wire the chime given it has five connections screws with no labels other t


... Vacuums

I have a motor for the Bissell 3750 power head with a black and brown wire, which wire is connected to what?? The old motor just had 2 black wires. There is a blue wire coming from the vacuum and blue wire coming from the light that are together, and a blue wire coming from the light and a black wire that are together. What does the blue and brown wire coming from the motor connect too? Thanks


... Bissell 3750 Lift Off Bagless Upright Vacuum

Wiring Just removed hair, etc and had to remove the motor and clipped the light wires. Reinstalled but blew lights. Wired series> wired parallel> deffinetly wired wrong have a diagram?


First, what is the model number? I'll shoot you a wiring schematic. ... Oreck XL Ultra Bagged Upright Vacuum

Local vacuum repair shop replaced motor in Oreck XL 2600HH and now the lights blow out immediately upon powering up the machine. I believe the wires for the lights were mis-wired to the terminal blades on the motor housing. is there a wiring diagram available to properly connect the wires to the motor housing?


Hello. if this repair just occurred return this vacuum to that repair shop as they owe you a valid repair. I agree that they caused the lights blowing out problem. They must repair this for no charge. If you work on it yourself they will blame yo ... Oreck XL2600 Vacuum

I have a remote Hunter Ceiling Fan w/ remote 1-2-3 fan speed buttons and one on/off/dimmer light button. Model Number CP-9110R. It only has one pull string and it is for the light. I would like convert the light to work off of a simple wall on/off switch and the fan to be controlled by a 3-speed pull string. Can I by-pass all the sensors and make it work?


I see noone has answered so I will.Yes,it could be done,but if there is not a conversion kit for your fan,it would not be wise to do it.For starters,all of the things required would probably cost at least $15.Also,there is at least one tool you would ... Vacuums

Miele S5000 (revolution 5000) vacuum cleaner - How do I open the casing? When the power button on the handle is pressed the green power-level lights on the handle light, but the motor sounds like it gives a little 'jump' but nothing more. The orange power light on the body also dims. I assume the motor or fan is jammed, but I can't open the body to find out. I've taken out to screws inside near either end of the handle, but to no apparent effect. I'm assuming the body is held together by plastic


... Vacuums

I replaced a Intermatic light timer with a GE 15086 timer. I have read several solution, but none fit my wire sceme. This is hooked up as a 3-way switch so the second switch can turn outside lights on manually. Here is what I have; Four timer wires: R B W G Wall outlet: B, B & R (Two), G, W bundle What ties in together to make it all work?


1) GE 15086 is not a 3-way timer.GE programmable timers are for single-pole switch replacement only. I have tested this timer, and own several GE timers, and many other brands.2) Open following link to identify timers that work for ... Vacuums

Adding hampton bay light model #430-727 to ceiling fan. ceiling fan works but lights dont work. connected white to white wire & black to black wire. what else can we try?????


... Vacuums

Trying to attatch the wires from the light kit to the fan but the blue and white wires from the fan have white caps on them covering the wire. Do these need to be removed in order to attach the wires with the wire nuts? If so, how are these white plastic caps removed?


They're called "wire nuts". Turn them counterclockwise to remove, lay the wires you need to join side by side with the ends of the bared sections even and screw the nut on. lp ... Vacuums

I have an antique 8 arm chandlier and want to put it up in my bedroom but the wire hasnt any differance in color, how do i wire it to the exsisting wire from the celing , what wire goes to what wire ? I wont be installing it myself but would like to know so i dont sound so silly


Starting with the proper wire gauge, always white to white and black to black. ... Vacuums

Picked the zig cp3g at car boot sale,just what i was looking for,but no instructions just wires been cut,tidy little unit.on the battery transfer switch, red, green and blue. and from lights green,aux brown,and water pump yellow.....firstly how do i wire to power up,and how does the single wires from unit not have return wires,thanks.


Hi,\015\012\015\012For your requirement wiring will be following: the green wire will be from the knob beside\015\012the tree switch to battery switch. Red wire will be from another side of battery\015\012switch to circuit o ... Vacuums

My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara


... Vacuums

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin


... Vacuums

Oreck trouble I replaced the plug and switch. black from motor to pole 1, black from plug to pole 2, white tied to white with a wire nut. When I plug it in it is powered in the off position. I have high speed at the high speed position, low speed at the low and off positions. Any ideas?


... Oreck XL Ultra Bagged Upright Vacuum

Purchased vanity light galaxy while instructins are clear for black and white wires it also has a green and yellow wire is this just a ground wire


The green and yellow wire is indeed the earth wire, black is the live wire and the white is the neutral for US connection. Please rate this solution. ... Galaxy Vacuums

My HEPA Shark Model 238 is great when the moter operates at high speed. However, periodically, it slows down resulting in no turbo action and virtually no pick up of eve the lighted dustball! Sometimes a good swift kick will bring the moter speed back to "HI", but sometimes no matter what, it won't speed up.rnHELP!


If the motor is over heating, it will slow down and may even stop all together. A solid knock could reset the thermal switch prematurely. Clean it as best you can around the motor and try it again. If it does the same thing, turn it off for 20 minute ... Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum

I have power at top of handle, thus start button light up. but when turn on nothing happens. I checked wiring and it all seems plugged in. The lights on the bottom of the cleaner (part of the base) don't light up. so somehow it makes since issue at base. HELP.. retired cop


Hi,\015\012Seems, the motor of vacuum has no power supply ( not connected yet). You may have a loosen/defective connection on motor cables/terminal. Please check and have it fixed. ... Oreck XL2200 Bagged Upright Vacuum

Wiring the switch for a kenmore vacuum cleaner I need to know where teh different colored wires go. It had a short in it so I replaced the plug but think I wired it incorrectly. Its a Whispertone 300 model 116.28612790 The canister works but the beater bar doesn't.( it worked before a rewired the switch. Thanks


... Kenmore 23313 Whispertone Bagged Canister Vacuum

Indicator lights on Bissell 7920


According to the owners manual there is a red light that signals temperature, this light will come on when the water reaches optimal temperature, the heater may need to warm up again. Here is a link to your owner's manual.\015\012\015\012 ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Wiring a Johnson motor in a Oreck upright with 2 light harness?


... Oreck XL2800 Upright Vacuum Cleaner Cord Hook Upright Vacuum Cleaner Cord Hook

I had to replace the switch in my Kirby G6. It took some doing but I got in out and the new one in. I must have miss labeled the wires because when I pull backwards the clutch pushes forward. Ther


Go to kirbvacuums.com and look up your model number ,they might even have a toll free number you can call ... Kirby G6 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1584 seconds