Having problems with your Vacuums ?

How do you change the big belt on the wind tunnell

Answers :

Depends on which wind tunnel you have, they are different. Some you can take off the bottom plate covering the brush roll, and the belt can be replaced, if you can't get to the motor shaft, the you have to remove the top cover to get to it.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you change the big belt on the wind tunnell

Depends on which wind tunnel you have, they are different. Some you can take off the bottom plate covering the brush roll, and the belt can be replaced, if you can't get to the motor shaft, the you have to remove the top cover to get to it. ... Vacuums

Changing belts on Hoover wind tunnel U6401

Take off the bottom plate covering the brush roll, 4 screws. There are 2 belts, if you replace both, put the V belt on 1st, then stretch the flat belt over the motor shaft, then over the bigger pulley along side the V belt.\015\012\015\0 ... Vacuums

How to change the V belt on hoover wind tunnel U6435-900 ?

Below I have listed a link to the manual which has instructions and a link to the V belt you need.\015\012\011\011\011\011\011\011Windtunnel Manual ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How do you change the Hoover wind tunnel belts?

If you turn the vacuum over there will be (4) screws that hold on the base cover for the roller brush. Remove the screws and the cover and you can get to the belt(s). You can get replacement belts here: ... Hoover Company Wind Tunnel U53019 Upright Vacuum

I have a Hoover Wind Tunnel Self-propelled vacuum. I changed the belts because the brush was not turning. After replacing the belts the brush is still not turning what can be wrong?

There are two belts on the wind tunnel this video will show you how to repair ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Model UH70120 Hoover Wind Tunnel T Series Rewind Model UH70120 purchased at Target - bagless How can I put on the new Belt? I have taken it apart but cannot figure out how to change the belt. How?

... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner

How to change a belt on a Hoover wind tunnel

It depends largely on the model. Do you know the model number? you can get any hoover replacement belt here:Replacement Hoover Vacuum Belts ... Vacuums

How do you change the belts on a hoover wind tunnel vaccuum

Flip the vacuum over push the pedal so the vacuum lays flat on the floor or table. Remove the four silver screws at all four corners of the brush area. Pull up on the plastic cover and remaove it. Lift the brush out towards you if this is a self prop ... Hoover Vacuums

Changing my vacuum belt on a Hoover wind tunnel bag less

HERE is video ... Vacuums

How do you change the belt on a hoover wind tunnel vacumn/ not self propelled?

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My wind tunnel keeps breaking its belt. The big one. The little one is properly attached. This is a recent problem so it has nothing to do with the rug height settings. I just broke two in the course of 15 minutes. The bag is NOT full, the brush/beater has been cleaned and properly attached Help.

Well will the brushes turn freely as they run in bearings if its got wool of cotton raped around the side of the brushs that will make them tight to turn and will brake every belt you put on it, in a flash,,,\015\012the other thing that causes ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Hoover Wind Tunnel, model #U6655-900. I have changed both belts & have cleaned the brush. It is difficult to push and I smell burning rubber. Do you have any suggestions?

The transmission for the self-propelled could be broken. That's the reason it's difficult to push and the smell ... Vacuums

My hoover Wind Tunnel vacuum cleaner's motor spindle keeps overheating. Because of the high temperature, it keeps burning through belts (the big, wide ones). I have taken it in to the vacuum repair shop about three times now, and the problem has never been fixed. Does anyone have any advice on how to fix this or should I just buy a new vacuum?

... Vacuums

Hoover turbo power 7300 wind tunnel v2 belt change

... Vacuums

Change belts on a Hoover Power Drive Wind Tunnel Series 900 vacuum

Try calling Hoover directly toll free at\015\0121-800-944-9200 M-F 8 AM - 7 PM EST. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Wind tunnel self propel not propelling - how do I know if it is the belt or the idler arm?

... Hoover U6485-900 Windtunnel Bagged Upright

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa

Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?

Check the Idler Pulley part Number 43241004 (Item 13 in the IPB) ... Vacuums

I have a hoover wind tunnel model# u6476-900 and I'm having trouble replacing the belt. The extra belt that came with it was belt # 38528-035 and it's smaller then the old one and I'm having a hard time putting it on. Is this the right size belt?

Yes it is the right belt. the easiest way to get that belt on is to put it on the motor shaft first, stretch and start at the top of the self propelled pulley and rotate til the belt tracks on. you will need to keep pressure on the belt while you rot ... Hoover U6476-900 WindTunnel Vacuum

My Hoover Wind Tunnel Bagless Pro Pet is making a very loud thudding noise when the belt rotates, belt seems to be intact and in place, what am I missing? Vacuum is less than 6 months old, belt is not worn and motor seems to be fine.

... Vacuums

Hoover Self Propelled Wind Tunnel. Keeps throwing off drive belt. New belt. Starts up fine, as soon as you release and lower handle, belt comes off spindle

Hi, it sounds as though that when you release the handle, I no this puts pressure on the brush or spindle, this is causing the belt to come off. You need to remove the roller brush and check it for any thing that may have rapped around it causing it ... Vacuums

Why wont the self propelled brush on the hoover wind tunnel work. large belt is ok. the small belt looks 0k.

No don't do that,have a little patience.check where the self propelled assembly is and see if anything got in there,something might be loose and the teeth are meeting each other.thats a good vavuum.i have 2 but their not self propelled.try taking the ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Replacement belt # for hoover wind tunnel model u5750-900. original belt # 38528-035, please

Your belt number is correct ending in 035. I have had luck with belt number ending in 033 also. ... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Have Hoover Wind Tunnel Sel Propelled vacuum. Had to put on new drive belt. Turn on unit and drive belt slides off the drive spindle.

Look for excessive wear on the unit around the pulleys and their brackets that hold them in place. It sounds like something is just worn out and the belt is either slipping because it is not tight enough or because something is not aligned straight. ... Vacuums

HI, my motorized brush barely turns.It makes a hot rubber smell. I took apart and noticed the spindle the belt turns on discolored from heat. Cleaned it, but still no turning of the brush.The vac is a hoover wind tunnel. As it moved accidentally touched the belt/ spindle and burned my hand a little. Very hot in area. Bright spark from motor noted. Was careful not to touch that part!

That means that the belt is stretched and it is slipping on the motor shaft, that is why it is hot and smells like burning rubber. You need to replace the belt. Here is the correct belt you need: ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0431 seconds