Having problems with your Vacuums ?

NEED TO REPLACE DRIVE BELT ON HOOVER VACUUM MODEL TURBO 3500


Answers :

Take off the brush roll cover, then take out the screws from the bottom to remove the top lid, the belt goes from the brush roll to the motor shaft.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

NEED TO REPLACE DRIVE BELT ON HOOVER VACUUM MODEL TURBO 3500


Take off the brush roll cover, then take out the screws from the bottom to remove the top lid, the belt goes from the brush roll to the motor shaft. ... Vacuums

I replaced the agitator bar drive belt on a Hoover Model U6432-900 upright vacuum cleaner, but it just slips when the drive wheel is spinning. Is there an adjustment I need to make? I don't see any adjustment spots.


You probably should have replaced the flat belt(38528035) also. But the drive belt has a idler wheel(#13) to engage it, is it riding on the belt, if not if may have jammed to one side and able to spring up against the V belt. It could have broke al ... Vacuums

Need a replacement drive belt for my hoover lark u4043 not sure about last no. it's an old machine, but this one is in perfect condition, minus the drive belt. my local vacuum specialist says they can't get them anymore. where can I get one or a suitable alternative?


HiAs you know the Hoover Lark was more or less a rebodied Hoover Junior. The U4043/ (are you sure its not U4034?) model should use the same round drive belts as the Hoover Junior 1346 so youre looking for the old rubber ring type belts which ar ... Vacuums

I need to replace belt #38528-033 on a Hoover WindTunnel vacuum model #U5463-960. I've had the vacuum for a long time and have misplaced all operational and instructional info that came with it. Any help would be appreciated. Thank you.


Replace the belt on a hoover washing machine ... Vacuums

The Panasonic MC-V7515 has two belts. The local vacuum repair guy says he only has a part number for the drive belt, which is UB-9. How do I find a replacement for the other belt, the one which directly drives the beater bars? By the way, this vacuum has great suction, but otherwise is far inferior to my previous Panasonic vacuums. The cheaper models aren't a good buy--stick with the more expensive models.


... Panasonic MC-V7515 Bagged Upright Vacuum

Hello. I have an electrolux glider upright bagless vacuum cleaner (UK model) who's brushes do not rotate any more. I'm guessing that I need to replace the drive belt but I have no idea where to start. I would appreciate any tips. thanks


Hello! There are two solutions to this as the Glider model you speak of could be the more old fashioned type where screws on the bottom foot plate (ie where the spinning brush sits) have to be undone in order to get to the drive belt.\015\012 ... Electrolux Vacuums

Hoover Legacy vacuum model U5072-930 - can't find manual, need to replace belt


... Hoover Vacuums

I need to replace the belt on the power nozzle of my Hoover Dimension 1000 Model S3491. Unfortunately, I have no written instructions on how to do so. I purchased the vacuum cleaner in the mid-80s. Are the instructions still available? Thanks in advance.


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=566792\015\012Generic problem for all Vacuums\015\012I need to replace the\015\012posted by Deb in Iowa ... Vacuums

I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.


... Vacuums

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a


Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

Belts I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do t


It is the flat belt that gets stretched and should be replaced at least every 6 months. The V belt wears down so it won't it right in the brush roll V. Maybe the belt tensioner wheel has a problem, sometimes they get hook up and won't engage the V ... Vacuums

I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do they re


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=675093\015\012Generic problem for all Vacuums\015\012I have a Hoover self-propelled\015\012Posted by kl ... Vacuums

I have a Fantom Fury and need to replace the belt. Please tell me how to get into it so the belt can be replaced. It is a Fantom Fury Vacuum Cleaner # 3680093 Fantom Technologies Model # F10051 01


... Vacuums

How do I replace the drive belt on a kirby G4? Actually the belt is already replaced I just need to know how to reattach that front part back onto the main vacuum. HELP


Greetings from GoVacuum,\015\012\015\012Here's a video we shot showing you in detail how to install a belt properly, and how to reattach the head properly. I hope this helps you;\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum

I just bought a Hoover Power Drive Concept Two Electronic vacuum from the thrift shop. It only needed two belts and seems powerful. But i don't understand what the small red button on the handle marked "Release Drive" means. Thanks for any insight! Anything else i need to know about this machine? Is it a good one? Are there high-performance bags available for it?


The U6311-903 is a self propelled vacuum. The the small red button will stop the handle from moving back and forth, which makes the machine go foward and backwards. The red button disengages the self propelled feature. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

Need instructions on how to replace the belt on a hoover dirt finder model u5321-930


You can download the manual from the link below:\015\012\015\012http://www.hoover.com/Media/ModelPDF/U5468900.pdf\015\012\015\012Please update the question & let us know if the information given was useful to you - Good Luck! ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

Ihave a Hoover Windtunnel self-propel model U6445-920. The belt from the drive motor to the big wheel will not run in the center of the wheel. The belt runs about 1/3 off the wheel. I have tried several new belts and still the same problem. What do I need to do to repair this problem.


The large wheel may be worn off center. If the belt stays on and is not thrown, you can run the vac. if there is wobble in the wheel causing a genuine belt to slide off replace the wheel mechanism. ... Vacuums

I have a Hoover Vacuum Cleaner, Runabout Supreme, on which the belt has broken. I purchased a new belt, part number 38528-040. I need some instructions on how to install the replacement belt? Thank you. JBS


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=728341\015\012Generic problem for all Vacuums\015\012I have a Hoover Vacuum\015\012Posted by Jimbob48 o ... Hoover Elite U5061-900 Bagged Upright Vacuum

Belt replacement Does Hoover Windtunnel V2 model # U8148-900 even take a belt? The owner's manual only describes how to change belt in powered hand tool, not the vacuum itself.


No belt- it is motor driven. what happens to these if the rollers get stuck(by- say, a Lego® or something)  is the roller itself has an insert which will break, requiring roller replacement. \015\012\015\012simple fix, but costs a ... Hoover WindTunnel V2 U8148-900 Upright Vacuum

I have a Hoover Preferred vacuum cleaner and the belt is broke. i need instructions on how to replace the belt.


... Hoover Vacuums

Lost manual on vacum need to replace belt - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


Remove the bottom cover of the sweeper head, then remove the brush roller along with the belt if still there. Clean the brush end-bearings--the roller ends and the interior of the bushings. Then oil the bearings lightly with 3-1 oil or similar. Place ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Need to replace belt on a Kenmore Model: 116 37312690 vacuum. Have taken torn belt off. Is there a diagram available? I have lost owner's manual.


Instructions:\015\012\015\012\015\012 ... Vacuums

I need a replacement belt for Hoover Elite upright vaccum ,model no. U5043-930. What belt do I get?


Hello, \015\012\015\012Your vacuum cleaner originally came with Hoover belt part number 38528027, however Hoover has now discontinued this part number, and replaced this belt with the new belt which is part number 38528040.\015\012 ... Hoover U5227-930 Elite Upright Vacuum

I need to know how to replace a agitator brush for a Hoover Fusion model U5180 900. I was given the vacuum, but without the manuals, so I have no instruction on how to replace the brush. I have already purchased the new brush. Thank you for your help


Please use the following link.\015\012http://www.hoover.com/pdfs/manuals/U5180900.pdf ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1603 seconds