Having problems with your Vacuums ?

Where can I find replacement parts for H2O mop SC393. I can't keep the flow going even after taking it apart to unplug the line. It pluged back up and I think it would be easier to just replave it.


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Where can I find replacement parts for H2O mop SC393. I can't keep the flow going even after taking it apart to unplug the line. It pluged back up and I think it would be easier to just replave it.


... Vacuums

Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet


Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I need to take the canister apart to screw the filter housing back in place. I can't figure out how to take the canister apart or another way to screw the filter housing back in place.


... Tristar Vacuums

I need to take the canister apart to screw the filter housing back in place. I can't figure out how to take the canister apart or another way to screw the filter housing back in place.


You did not identify your model and the TriStar website does not provide manuals. They do have a FAQ page which does provide some illustrated guidance which may be helpful. See here:\015\012\015\01 ... Tristar Vacuums

I have an Electrolux Oxygen 3 vacuum I purchased rebuilt. After 1 month the power stopped working. I took it into Electrolux Authorized repair dealer, which was a horrible experience. When we received it back it was clearly not as powerful as before. Does anyone have any suggestions on what the problem may be? I would rather fix it myself than take it back to them. The next repair center is too far away. I am pretty good with fixing things, just needs some guidance. I think the repair center rep


Never have liked Electrolux doing any repair because it has been my experience that they don't do what they say they did....if you can read between the lines.....give me a picture of the unit and more details and I'll try and help you. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

We had to take the machine apart just to see that the belt had broken after only 5 use's . We can not see how we are ever going to put the new belt back on. do you have instructions on how to take the belt off and how to put a new one on? Please send me one.


I have a Panasonic MC-V5746 upright vacuum. According to the booklet, \015\012MAKE SURE UNIT IS UNPLUGGED.\015\0121. Place carpet-bare floor selector in "carpet" position.\015\0122. Remove lower plate (there are two screws in the m ... Vacuums

My Jacuzzi Tracker 4x just "stopped"..there is a nice strong flow of water going into it, but the wheels just aren't turning. I've tried the following to no avail: 1. blocked suction for a few seconds underwater with my hand (this has worked in past) 2. try to move front wheels back and forth (but they won't budge...back wheels do move on track though) Should I start taking it apart?


... Vacuums

My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?


Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I can not get the water, normal heavy traffic selector reinstalled after taking unit apart, i replaced the pump, and now i cannot get it back together, there seems to be a special way it goes together, and i'm not finding it. Are there any videos, or pictures that show how it should go back together?


... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430


Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

A baby sock was sucked up and stuck where i can't see it in my regina electrikbroom cleaner - 11.4 amp. i have tried to get it out and now i have to take it apart i think and can't get the housing apart - what should i do?


... Regina ElectrikBroom RG100 Vacuum

Changing belt How do I do that? It looks like I would have to take the screwdriver to the bottom and enter the engine compartment. I'm not sure that I feel confident to take this machine all apart and be able to get it back together again.


Its not the engine compatment take the screws out the cover 4 the roller will come off then u can c where the belt goes ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

I take apart and clean my DC17 every 2 weeks. When I put it back together it always works perfect. This last time, I noticed that the self propel is not working...am I missing something? I took it apart to be sure eveything is in it's place but no difference. Now I have to push really hard.Any suggestions?


The roller is not spinning do to motor or belt not working. If it is the motor then the machine will have to go back to dyson if it is the belt then that is an easy replacement. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.


Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

Sebo X4 is squealing when pulled back. Takes a while after it's been running for this to happen. We changed the roller brush (needed it anyway) but didn't take care of the noise. Could the wheels be making this sound? At least that's what my staff thinks is going on... I own a commercial cleaning company and all we use are sebos... they're an amazing machine!


Yep - we think Sebos are pretty good too. I work at a Sebo sales and repair dealership! The wheels are a good bet - I can't think of anything else that might cause the noise. If in doubt, I suppose you could simply wheel one around for a while when s ... Sebo X4 Bagged Upright Vacuum

I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together


... Vacuums

My Hoover Whisper Cyclonic is collecting the dirt but not taking it into the cylinder. The brushes were at one point starting and stoping due to the belt periodically turning,now the brushes are turning and the dirt just collects and I'm starting to smell a an oder like rubber burning.I've taken it apart and tried to make sure the is no clog. The one hose that I can't check is in the back right base, above and left of the right back wheel.


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

How to I take apart and front and back of the Bissell 8910 pro heat.


... Bissell 8910 ProHeat Clear View Upright Vacuum

I had to take apart hand tool for steam vac and now I cant get it back together. Please help.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Had to take my black and decker leaf hog apart and am not sure how it goes back together. Is there such a thing as a diagram of the inside layoutg?


... Euro-Pro PT205 Leaf Blower Powerful 12 AMP Leaf Blower, provides 205MPH air speed, Detachable Vaccum... Vacuum

Lost suction my DCO7 lost suction in the hose I started taking it apart and cleaning it and looking for clogs (probably more than I should have) and when I put it back together it has awesome suction in the hose but no suction in the base. It just pulls the pine needles up (christmas tree) but they never appear in the "bag" compartment and when I look they are just all gathered in a clump in the bottom by the brush.


Hi.\015\012\015\012Remove the sole plate turn the 3 plastic screws to unlock & lift off.\015\012\015\012Now remove the blockages that have accumilated from the oppening of short clear hose.\015\012Check you can turn ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a hoover f5914-900 steam vac.. and I was wondering if there's a way to take apart the spin brushes to get them cleaned out well. I loaned it to family, and the brushes came back extremely soiled and not spinning.


The brush block may be removed from the base for rinsing.\015\012Yes, you can CAREFULLY disassemble the brush block assembly by releasing each of three latches that hold each of the clear gear covers to the main block. A small screwdriver is u ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I can't figure out how to put the dirt devil kone back together after taking it apart! Help!


... Dirt Devil KONE Hand Vacuum MO213BLU Vacuum

My powerhead on my EXL Tri-Star goes on then shuts off. When youturn it upside downit runs, then back on the floor it stops. Is it the belt inside the powerhead and if so to I take the head apart and replace this belt. Can any vacuum repair place fix this if I have the part. Vacuum was purchased in March 2000 Thank you, Dianne Miller [email protected]


A vac shop is probably going to require you to use their parts for warranty purposes. but its pretty simple. most shops should be capable to do it. ... Vacuums

How do i take apart vac to unclog . how do i unhook the hoses to unplug


... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0647 seconds