Having problems with your Vacuums ?

My belt that connects to the brush wheel. how do i connect it?

Answers :

Depending on the model you have, you'll have to remove the sole plate (i.e. the foot plate where the brush meets the carpet) and then stretch the belt over the motor flywheel. Dont try it the other way (i.e. get the belt on the brush and then pull roughly to meet the motor flywheel)  as its easier to get the roller brush over the belt and then strongly push the beater bar/roller brush back into place making sure both ends are seated properly. Then fix the sole plate on securely and switch on to see if it works.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My belt that connects to the brush wheel. how do i connect it?

Depending on the model you have, you'll have to remove the sole plate (i.e. the foot plate where the brush meets the carpet) and then stretch the belt over the motor flywheel. Dont try it the other way (i.e. get the belt on the brush and then pull ro ... Vacuums

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.

... Kirby Ultimate G Bagged Upright Vacuum

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a

The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

We own a dirt devil model 088600, and are experiencing a problem with the belt wearing away a section between where the belt connects to the brushes and the motor. There is a lot of plastic/rubber residue coming out from the vacuum. We have tried new belts only to find the same problem occurs. I noticed that the source of the dust is coming from the section between the brushes and motor, where there appears to be a section that is misshapen and melted. I looked up the schematic online and can't

If you are certain that the belt is seated correctly and the beater bar is nested in its holder and the cover of the assembly has been properly installed and you still see a contact area between the belt and cover, you should either: return the vac ... Dirt Devil Vacuums

My simplicity 7 series vacuum belt turns the agitator (beater brush) turns freely by hand when the vacuum is unplugged or off but when I turn the vacuum on the agitator does not spin even though the belt is moving. Could there be a worn out part at the agitator pin where it connects to the flywheel that the belt is connected to?

... Vacuums

Fan belt wheel missing. Took it apart and discovered fan belt torn and no wheel on drive shaft for brush. I am assuming that there was one there originally.Did it shatter or what.What is solution. Can I get exploded view of this model or others like it.

Get another fan belt wheel of the model and place it over it ... Vacuums

I have a bissell 9300 carpet shampooer..the belt broke o n the left side. tookoff the plasitc brush shield to access the area to put on the belt but not sure how to connect it to both brushes..only one comes undone...do i have to unscreww the whole thing?

Follow the link below on how to change the belt.\015\012http://www.bissell.com/VideoRating.aspx?id=1557 ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou

Try this link belowhttp://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless- ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag

... Euro-Pro EP621 Bagless Upright Vacuum

There is a metal post that spins and rotates the belt at the opposite side from the brush. the removable wheel that holds the belt onto the metal pin is missing. how can i buy that part? eureka whirlwind lightspeed #5844

Vacuum 24x7.com, they should have the parts ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

I have an old Riccar N2000 (biege) the belt connects to a little ''tension'' piece or ''guide'', not to the brush directly as in newer models. When moving-- this piece is somehow no longer there? Where can I get another one? Went to shop in town, they want $60 + labor to put the ''newer'' one piece brush thing in.....

... Vacuums

My Hoover Whisper Cyclonic is collecting the dirt but not taking it into the cylinder. The brushes were at one point starting and stoping due to the belt periodically turning,now the brushes are turning and the dirt just collects and I'm starting to smell a an oder like rubber burning.I've taken it apart and tried to make sure the is no clog. The one hose that I can't check is in the back right base, above and left of the right back wheel.

... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Took appart turbo brush and don't know where to put belt to make brush spin...what two things should it connect?

Hi,\015\012I have a Kirby turbo brush. The belt drives the brush roller and also the big roller that is inside the turbo brush. ... Vacuums

Hoover 2000W dust manager cyclone- Have had this for about 2 months and the brushes stopped turning thinking that the belt had acme off turned it over to try to get in to look at belt now the bottom wheels have came off and will not go back on have not lost any bits literally just undid one screw! Please help!

... Hoover Vacuums

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile

... Eureka Smartvac 4870 Bagged Upright Vacuum

Can't get to motor to connect belt after removing brush cover

I followed the instructions that were supplied @ the FixYa site, to remove the hood. Removing the hood was the problem. Just follow the online users manual pages 22 thru 26. you must spread the hood by the rear wheels to remove.\015\012Thank You Ve ... Hoover Soft Light Supreme U4262-930 Bagged Upright Vacuum

I took off the brush roller to clean it and now I can't get the roller to work unless the machine is standing upright. The side that's not connected to the belt keeps falling out.

The solution for your situation is as follows: You need to put the retraining clips on over the arms to properly put them in place You most likely put the retaining clips on too early. ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I have a Necchi 522, an early mechanical stretch stitch machine. The timing and stitching are great, but over the past few projects I have noticed a balky tendency when I press the knee bar. After my last project the motor almost won't engage. Sometimes there is no sound, and sometimes there is a weak whirring, but no action until I push the hand wheel. I have a feeling that it is either the v belt or that the motor needs new brushes. Are either of these ideas likely, and if so, are they self

Hi,It sounds like the machine is having to work too hard. Have you cleaned and oiled your machine lately? Over time oil will harden and lint and dust will build up on the working parts in the machine causing it to drag and eventually stop ... Vacuums

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?

Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

Hoover self propelled bagged windtunnel upright model #U6435-900...how do you remove the green plastic shell cover to get to the part that secures the v belt...we need to secure the bolt and cannot get the area. Brushes and transmission wheel not rotating? thanks

Greetings from GoVacuum,\015\012\015\012Here's a great video repair tutorial that we've put together to try and help you with the repair on your Hoover WindTunnel. I hope that this helps you with your repair. If you found this solution ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Upright Bagless WindTunnel does not self propel (U6625-900). Belts are new, Brush turns strongly. Wheels propel forward very weakly and do not reverse when the handle is pulled backward. Is there a mechanical link from the self propel switch to the "transmission" ? Are there any gears that could be worn or not engaging properly?

... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Bissell pro heat carpet cleaner, won't move forward. both belts working. is there something that is suppossed to hold the brush bar down so the carpet cleaner uses that as it other set of "wheels"

... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a

... Bissell ProHeat Deep Cleaner Upright Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2843 seconds