Having problems with your Vacuums ?

I got a Kenwood Chef KM336 couple of days ago - seems like there is aa problem - when kneading stiff dough, the lever realeses the lock and the mixers head go up (while working?) Shall I got that replaced?


Answers :

Ensure the main body mixer head is pushed down firmly before mixing the lock should not release unless you have overloaded the machine e.g. too much mixture in the bowl.

when you lower the main body down and the lever snaps just place your hand on top of the machine and give is a second push to ensure the lock as really caught.

if this persists then I would consult your supplier for a replacement or refund under your consumer rights and or garantee from kenwood.

I hope this was useful
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I got a Kenwood Chef KM336 couple of days ago - seems like there is aa problem - when kneading stiff dough, the lever realeses the lock and the mixers head go up (while working?) Shall I got that replaced?


Ensure the main body mixer head is pushed down firmly before mixing the lock should not release unless you have overloaded the machine e.g. too much mixture in the bowl.when you lower the main body down and the lever snaps just place your ... Vacuums

No suction I have a similar problem - volta vortex bagless vacuum will not ****. Worked for 1 job then quit sucking, I have had the heads replaced, then the barrel - 2 months later same problem. I push the power lever to max - 10 seconds later it turns itself down and doesn't work properly. I am over it, now looking for refund


Hi there SmartAlec from NelsonVacuums.com.au here. The problem is going to be the filter. THis kind of vacuum basically replaces the bag with a simple filter and the vacuum ... Vacuums

The motor on my Epic 6500 works, the hose is sucking, but the power head isn;t working... I tried the sidestep power head and that one works. Ive opened and replaced the belt and that is fine. The bulb was already burned out and wasn't replaced so I cant tell if theres power to the head. What else could it be?


Connect the power nozzle directly to the hose and try.\015\012Check the terminals where the wand connects to the PN. If any are discolored or cracked, that may be the problem.\015\012Open the PN and check for loose or broken wires and co ... Electrolux Epic 6500 Vacuum

Our unit is 7024A Electrolux Oxygen 3 - it seems to work great but suddenly, the head or 'power brush' or whatever it is called - has died. I checked by removing the hose and plugging it directly into the body, but it is still dead. Without that motorized head working, the vacuum is useless. Is it worth replacing? The unit is only about 1 year old and has seen light use only. Very frustrating, since it was the most expensive unit in the store:(


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Hoover U5344-950 My Hoover vacuum is a nightmare! I have had nothing but problems with it since day 1. The powerhead stops working if you try to lower the handle to vacuum. I took it in to be serviced and was told it sat on the shelf for too long in the store and it warped the belt...so it was replaced. Got it home, it worked the first time I tried it, then went right back to no powerhead working and as a bonus it is giving off a nasty smell like it is going to blow up! It now gets really hot to


... Hoover U5344-900 WidePath Vacuum

Need part for stand of Hamilton Beach Scovill Model 44 Mixer. Part is locking rocker tab that hold mixer in place on stand or press to remove mixer head from stand. Don't need spring or pivot pin, just rocker tab. Don't have part number.


... Vacuums

Rod problem... One of the electrical connection posts that are on the top of the rod appears to be broken which causes the power head to work only when it makes contact. Is this repairable? If not, is it replaceable? If not, are the rods available for purchase? The vacuum cleaner itself works well,


You would need a new wand. this might work for your unit. ... Fantom Vacums Lighting Canister Vacuum

My Ultralux 2000 vacuum power head does not work on my machine but does work on a different machine. What are the possilbe problems? I tried replacing the hose with a new one and that didn't help.


It's probably due to bad wiring connections between the wands, hose and wand, or power nozzle and wand. If it came with the Sidekick, try using it on the end of the hose. If not, simply try using the power nozzle on the end of the hose (no wands). ... Electrolux Eureka Easy Clean 2 in 1 Stick and Handheld Vacuum Model 108A 1 ea

Dear Sir/Madam, My old faithful Hamilton Beach Mixer, now 60 years old, is still working but recently I was told by someone who looked at the motor that it needed repair or replacement. Is it still possible to get it in working condition?


If the armature shaft is worn there might be a problem, but that would be about the only one, Bushes/bearings can be replaced as can brushes. If the armature shaft is worn, a fix can be formulated but it will require some ... Vacuums

On the bottom of the Fantom Fury where it states:"The United States and Canada utility patent....". Now go to the far right end of this statement (the end opposite the spring, well I have a crack in the plastic which, when toggled, moves the entire plastic underside of the vacuum to move. In other words, I think I need an entire bottom plastic plate. The cracked area also makes the foot lever (which lowers or locks the vacuum handle) not work as the crack makes it impossible to work. I know


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=545424\015\012Generic problem for all Vacuums\015\012On the bottom of the\015\012Posted by c ... Vacuums

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther


Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Hi, my power head is not working on model 116 5416083 and I cannot open it up. I think there is a gasket that needs replacing.


If you press on either side of the raised top light cover it will come off. Then you will be able to see the light bulb and two screw heads. Remove the two screws and the ... Vacuums

My Vacuum just stop working. I was cleaning my car carpets when it just went off. I tough it got disconnected from the outlet (power supply). The vacuum was connected and it is like when a fuse go bad, just like that it won't turn on anymore. Is there a switch that needs to be reset or a fuse to be replace? How do you do it?? Thanks


There is not any of that. Buy a new one ... Hoover Empower Bagless Upright Vacuum

Power head on my Electrolux Epic stopped working. Do I need a new one or could there be a part that needs replacing. Can I open it to see?


Have you tried pushing the reset button? I'd try that first. If that doesn't work it could be that the belt is broken. The motors don't go out very often on those. ... Electrolux Epic 6500 Vacuum

I have a Kirby Heritage II which normally works amazingly well, but it's not playing at all nicely today - and of course we have apartment inspections tomorrow. *dies* The belt broke today (as did the replacement belt, which I'd bought at the same time, so apparently the rubber was old), so I went over to Stark's to get some new ones - but it still won't cooperate. I've taken the head apart and put it back together several times, to be sure that everything is properly seated, but it's just not


... Kirby Heritage II Vacuum

I have a Bissell ProHeat 2x, and I did something dum. I had some powdered cleaner that said it works with carpet cleaners-well I mixed it in-and the next time I tried to use it, nothing came out. So, I took it part to check what was wrong-and found out that the powdered cleaner solidified in places. I cleared the nozzels, nothing. I think the solenoid, between the heater and nozzels is pluggd, and possibly the heater. I've got a question-could I use CLR to clean the heater, with replacing t


Heck yeah, give it a shot. Try running some water through it too- fill it up, heat it just to where it's hot and unplug it, shake it around and dump it out. Repeat. You might have to get a wire or something to go through and get the powder loosened b ... Bissell Vacuums

Our Kenmore Vacuum Model # 116.22950 will not turn off at the switch. I have to unplug it to stop the machine. My husband just tried to replace the switch on the handle but this did not work. We got a new switch.


... Kenmore 2029915 Canister Vacuum

Sharp R-1480. Microwave would not start - jarred door, and it heated and worked. Replaced bottom of the 3 inter-lock door switches. Turns back on - all seems normal. No heat (it does overall sound louder). Thanks, Mark [email protected]


Hi Mark,It sounds like you have a magnetron problem now or at very least a rectifier that is shorted. The elevated sound level comes from one of those two components. But since you had a door switch problem I would lean toward ... Vacuums

The self propelled feature does not work. Belts are OK but the drive wheels do not seem to be engaging. Is there a cable or something from the lever on the handle that needs to be replaced?


My vacuum cleaner does not turn on \015\012could it be the motor out \015\012i check the switch it ok not getting any power to the switch ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Miele S1721 Powerhouse upright vacuum. When the belt broke I took it into the shop (because when i tried to replace the belt, the tension was so tight I couldn't get it back together!!). When I got it home I DISCOVERED THAT THE HEIGHT ADJUSTMENT DIDN'T WORK anymore. It seems like it's set really hight, because it no longer contacts and brushes the carpet. So it's now useless. I went back to the shop and the tech denied that there was anything wrong. (I didn't have the vac with me). No


Hi\015\012The Miele uprights (S170 and upwards) with the Powerhouse title are ALL Panasonic uprights which have been at one time sold in the UK. Therefore the upright may use TWO drive belts which need to be looked at: Take off the sole plate a ... Vacuums

I got my Mom's Kenmore sewing machine and I an trying to figure out how to get the scalloping and arrow head stitches to work. I have followed the manual and I can get all the other stiches but those two. It is a Model 1451 zig zag machine. I realize it is old, but the machine is just like new. HELP. Thank You.


... Vacuums

I have a kenmore vacuum cleaner model # 116.23612. When the hose is attached to the canister it runs, but if you remove the head to just use the hose the unit stops working. Is the motor dead or is there some type of reset or fuse. Could you please tell me how to test this. If so could you please send me instructions on how to replace the motor. Thank you in advance for your help, Tony


... Kenmore Vacuums

I have a kirby sentria vaccum carpet shampoo system and I cannot get the shampoo suction head to work! It comes on but the belt is not turning. I have tried taking it off and looking at the assembly but no luck. And I have tried turning the belt engage lever to off and on to see if it makes any diference.


I had the same problem at first but figured it out. Make sure before you put it on the vacuum itself, that the shampooing unit is completely together. The belt needs to be taunt like it would be when the brush is turning. Once you put it on and turn ... Vacuums

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Little green machine pro heat pet the collection tank wasn't collection and dirty water was coming out of the bottom. i took it apart, cleaned it up and put a new "duckbill" gasket in. then it quit spraying, but i think i got that working again. now after i spray and get a good foam on the carpet, i switch to suction and it seems very weak. i can see the water moving (trickling) from the head into the hose but it is not reaching the collection tank -- actually, i am not sure where its goin


... Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0998 seconds