Having problems with your Vacuums ?

Steam is coming fromthe join between the white base and the grey plastic on which the iron sits.How do I separate the two plastic mouldings so that I can see the problem


Answers :

Hi,
\015\012
\015\012You probably wont like the answer, but the unfortunate truth is that you don't separate the plastic mouldings. They are bonded together. Irons do not contain any user serviceable parts.
\015\012
\015\012If you separate these mouldings you will not be able to put them back together. Any attempt to separate them and then put them back together and/or re-seal them is highly dangerous. This is a hand-held pressurized vessel containing boiling hot water. When they leak, they need to be replaced.
\015\012
\015\012Hopefully, you will not find any "expert" guides published on the internet for making this type of repair. Anyone suggesting you do so is highly irresponsible.
\015\012
\015\012Unfortunately, you will need to replace the iron.
\015\012
\015\012Regards,
\015\012BElectric
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Steam is coming fromthe join between the white base and the grey plastic on which the iron sits.How do I separate the two plastic mouldings so that I can see the problem


Hi,\015\012\015\012You probably wont like the answer, but the unfortunate truth is that you don't separate the plastic mouldings. They are bonded together. Irons do not contain any user serviceable parts.\015\012\015\012If you ... Vacuums

We bought a Philips Intellicare 8030 ironinng system in 2005. Two days ago water from the plastic water container does not go inside bigger water tank where we think the water gets heated up. When the heating tank is empty there is no steam that comes out of the iron. Also, there is water dripping off profusely from under the iron where the steam normally comes out. Can you please advise how we should remedy this problem Please advise which service centre in Sydney, Australia would we be able to


... Philips Vacuums

I just bought a Tfal Ultimate Autoclean iron FV 9450. I am reading through the manual and trying to figure out all the parts and functions. I cannot figure out how to remove the anti calc valve. I see it is part # 12 on the drawing but that piece on my iron (the bit with the little circles on it where it says, " anti calc plus') seems to be a flat piece of integrated plastic with no give or slide to it. .I cannot see how I'd possibly remove it. What do you do - push up? push down? The i


Anti-calc valve wings (grip) located at #3 of the 1-15 labeled description diagram that is part of the instruction manual. The wings are on either side of the dry/steam control #4. Lift up on the wings (grips) and the dry/steam control will accompan ... Vacuums

Breville Ultraglide 2200w steam iron The auto shut off has occurred on two occasions, after which the iron would not get hot or even warm. I am not sure if these are linked or whether there is a different problem.


... Vacuums

My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current


I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum

Hi. We've got a Dyson DC17 "Animal". It's clogged, and we are unable to separate the purple cyclone cap from the main cyclone body to get to the problem. We've heard of 4 torx screws that take some interesting tactics to access. I've been through this thing with a flashlight, and torx tools for a protracted period, and even after removing the torx screws was unable to ultimately separate the two pieces (main body from purple cap assembly). Any help would be greatly appreciated. Thanx -


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Roomba Stops I've had a Roomba for about 2 months. Lately, it runs for about 45 secs, then stops, makes a two-tone (descending) sound, and flashes the CLEAN button while the STATUS button is red. I've emptied the dustbin on it. Can you help? I am seeing the same problem on my roomba today. I cleaned all that I could., the brushes, the pins on the sides and all that and it still gives the same problem..Any other fix?


Run your roomba through a self diagnostic test. I have posted the link below. Tell me your findings.\015\012\015\012\015\012http://mysite.verizon.net/gsplews/Diagnositic-Tests_Proc.v.0.5.htm ... iRobot Roomba 4210 Bagless Robotic Vacuum

Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus


... Bissell 6595 Lift Off Bagless Upright Vacuum

The metal rod inside the handle fell out when i separated the two handle parts to replace the square metal post/handle. I do not see a purpose for the metal rod or where it connects near the on/off switch. XL upright Oreck model.


It is like a static ground post your right it really dosent do anything ... Oreck XL2000 Bagged Upright Vacuum

I have a durabrand food steamer model number FS1146R (ASDA spec code: 195/121). it is white a the bottom with a timer and has two clear plastic steamer compartments. The problem I have is that the handle on top of the lid has broken off. My husband has repair it a couple of times but can't do it anymore. Is there any chance I can purcase a lid as the rest of the steamer is still in good working order. How much would the lid cost? Many thanks Barbara Waller


... Vacuums

Dyson 28 airmuscle... carpet level selectors will not stop blinking... I have tried all selectors to see if an adjustment helps It has not lost section but the blinking light tells me something is up... I have two vaccumes one for upstairs and one for downstairs. all same carpet in the house and I use the medium pile and only one of the vaccumes is having this problem


... Dyson Vacuums

How do i remove the front of the Proheat Clearview to clean it out? I removed the two obvious screws at the front sides of the clear plastic part but see anything to remove to take it off.


... Bissell 1699N ProHeat Clear View Force Upright Vacuum

Belt slipping Belt slips off and rubs causing burning smell from the belt over heating. Of course this puts an indent into the belt and has to be replaced. How do I keep the belt from slipping off? I see no place for a belt adjustment. Which I know would eliminate the problem. Really aggravating to have to replace belt only after two uses.


On the roller/brush where the belt sits if that is scarred up or grooved out that will cause the belt to slip if you can fix roller try but i suggest new roller ... Hoover Company Wind Tunnel U53019 Upright Vacuum

Good day, I took off the cover on a proheat upright, to install the suction diverter flap. Guy at the shop told me I had to do this but I don't think it was really necessary. Anyway, I am having a real job getting the cover back on. The shampoo mix piston seems to be causing the problem seating the two halves correctly. I see no obvious "right: way to put the piston back in. can anybody help me. Thanks Richard


Hey Richard. Turn the shampoo mix dial so the spiral is all the way at the top when you are looking at it from underneath. then, you want the piston to seat in the top groove of the knob. You want the piston's end that jets out to fit in the space ... Vacuums

How do I take apart the body of dirt devil 82500? I think something shorted out, and want to see if I can fix it. I took all visible screws out of body, but still can't separate the two halves to get to the motor


This is sort of easy, and hard at the same time. \012\012First remove the dirt canister and hose. \012take out your exhaust filter. \012find all of your screws on the one side of the unit and remove them. \012you will fi ... Dirt Devil MO82500 Bagless Canister Vacuum

We have two of these vacuums and both of them have experienced the same problems. First the floor heighth adjustment doesn't work and now neither one will pick up on either carpet or floor when in the brush/floor mode. They both seem to work with the suction hose function. We have removed the back panel to see if there was an obstruction but it was clear. We have changed the bag and the small filter (not the HEPA filter) all to no avail. What else can we do? We are desperate to use our vacu


Did you check the powerhead for obstructions? With a bend in the tube just below where the hose connects, this is a common spot for clogs. To check, detach hose and drop a coin in the hole. If it doesn't drop through, a blockage is present. Use t ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

I have a Howard Miller Westminster Chime Mantle Clock. It has always worked fine. It stopped working and my husband took the battery out to change it and when the new battery is in it will not work. It is Model 613-=103 movt 354201J dial 272142J. The part you put the battery in almost looks too big for one double A but I can't see how two would fit. I am afraid the battery is just not in right. Can you help me with how many batteries go in this clock or if it is one what the problem could be.


... Vacuums

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help


Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

DZ9080 IRON IS NOT VERY OLD, BUT HAS HEATING AND STEAMING PROBLEMS. IT MAY BE ALL HEATING RELATED! MY WIFE WILL SOMETIMES JUST LEAVE IT "ON" FOR TWO HOURS AND THEN IT WILL START STEAMING AGAIN. I CANNOT MAKE SENSE OF THE HEATING INDICATORS; SOMETIMES IT WILL STAY GREEN NO MATTER WHERE YOU SET THE DIAL ---- AND IT DOES NOT FEEL HOT! WHEN I TRIED IT AGAIN TODAY, THE SHOT-OF-STEAM WORKED FOR A WHILE (AND THE SPRAY WORKED), BUT THEN ALL IT WOULD DO IS DRIP WATER AT THE TIP WHEN TIPPED DOWNWARD.


I couldn't find any warranty information on this iron, but I suspect that the heating element either has a faulty connection or part of it has cracked, making contact at time, but poor contact at other times. The unit will have to be taken apart an ... Rowenta Vacuums

I noticed the Roomba's brushes were not sweeping, or turning so they could sweep. There was a new sound coming from the machine, the sound of grinding nylon! Upon inspection, I determined the problem to be a heat melted gear support hole. The hole was no longer round but oblong. You could see a ridge of plastic around this hole. So melting I believe was the culprit. The gear that uses that hole was then able to tilt to one side, thereby allowing the gear to disengage from the drive train. I


Be sure to keep your brush bearings clean. If they get clogged, the brushes don't turn and the drive sockets can get damaged. ... Vacuums

I have the Dyson DC 14 and have had it for almost two years. Now it leaves clumps of matted hair from my dog on the tiled floors. There must e a problem but I don't see anything wrong.


Hi, There could be various reasons why this could happen.I will tell you the reason's that could cause this problem and it solution.Please try it,If still the problem persist,you could call the customer care.1) Int ... Dyson Vacuums

I have a Kirby G4 it will start with the hose attachment but not the vaccum housing attachment ? I'm guessing a problem w/ the switch ....when I look at the switch I see two buttons I can actually


Check this vieo out these are safty switches ... Kirby G4 Bagged Upright Vacuum

I shipped my brother PE 770 embroidery machine purchased sept of 2010, to a lady who perchased it on ebay. Had used only once. Everything worked fine.I shipped in the original formed styrofoam box. I removed the embroidery arm, releasing the locking plastic hook holdind the machine and the arm together. When to lady removed the machine first in the original plastic shipping bag, two parts fell out. Her photo she emailed showed a black plastic piece with two holes or pivot points.also a silver me


This is a link to the manual for this machine. Do you see a picture in the manual of the parts you are describing? Reply with a part number and I will do my best to help. ... Vacuums

Have Electrolux 1590 whole house vac, and can't see how to get brushes out. Leads so short, and don't want to break them trying to free brushes. Do they slide out of plastic housing? My eyes not real good, but it looks like the leads are part of a brass sleeve that slides into the plastic housing. It also looks like the plastic housing may be a snap lock type, but I don't see how to open it.


... Electrolux Vacuums

My Triton T80 SI shower is leaking from where the outlet pipe assy joins to the heater can assembly. when I checked where the two join together I see that there is a rubber O ring fitting into a recess in the heater can assy. The screws which hold the two parts together does not force a compression between the two parts causing it to leak. Is there another modified unit or am I stuck with what Ive got and should I replace the O ring or the shower.


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0424 seconds