Having problems with your Vacuums ?

How do you replace the belt on the Kirby, Model No D50, Serial No. A442867


Answers :

Generic problem for all Vacuums
How do you replace the
How do you replace the belt on the Kirby, Model No D50, Serial No. A442867

I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure.
This is an older Kirby vacuum and the front brushroll section of the vacuum and the front brushroll section will come off, 1st you have to remove the front cover (the Kirby Emblem) and under that there is a Kirby spoon or hook and you need to dial off the belt off the belt shaft, once that has been done remove the bottom plate and un-install the Kirby brushroll, check to see if the brushroll spins freely, if it does go onto the next step, if not clean off the hair and thread from either end and then re-check the brushroll, if it still binds up then replace the brushroll and belt with Genuine Kirby belt and brush. Then use the dial to place the belt onto the Kirby spoon / hook. Once the belt is on the hook, install the bottom planter and place then housing of the Kirby on the vacuum and use the lever on the top to secure the fan housing dial the belt onto the pulley and you should be good to go.
http://kirby.com Contact Us by Phone
United States and Canada 1-800-494-8586
Between the hours of 8:00 am to 5:00 pm EST
Monday thru Friday

\015\012
\015\012Don – The Vac Man
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you replace the belt on the Kirby, Model No D50, Serial No. A442867


Generic problem for all Vacuums How do you replace the How do you replace the belt on the Kirby, Model No D50, Serial No. A442867 I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service proc ... Vacuums

After replacing the flat bet and v belt on my Hoover model U6433-900; serial No. 12300043057, purchased June 23, 2004, the brush roller still does not turn when I release the foot lever to vaccuum.


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=725351\015\012Generic problem for all Vacuums\015\012After replacing the flat bet\015\012Posted by maha ... Vacuums

My vaccuum has lost suction. I changed the bag and cleaned everything out. The vaccuum is only 6 years old. I even replaced the belt around the brush. When I turn the vaccuum on it smells like burning rubber. My vaccuum is an upright 12 amp model #33000300C serial #Y347012385


... Kenmore Vacuums

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?


First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.


... Vacuums

Belt replacement i am trying to replace the belt on my kirby g4 and i can not get the rooler off to replace the belt. if you could tell me how to do this it would be great.


Lift the light bulb housing up and you will find a latch that will rotate to release the front agitator housing and remove it from the machine. On the bottom of that housing, there are two latches that secure the bottom plate that covers the roller. ... Kirby G4 Bagged Upright Vacuum

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.


The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums

The belt on my Kirby G3 wore out, and I bought replacement belts from two different sources--one an official Kirby supplier and one a store brand. Neither belt is long enough to catch the belt lifter when it is rotated and to reach the drive shaft.


Kirby has only had 1 belt from day one. sometimes you do need to push the belt up to catch the belt lifter ... Kirby Generation 3 Bagged Upright Vacuum

Belts I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do t


It is the flat belt that gets stretched and should be replaced at least every 6 months. The V belt wears down so it won't it right in the brush roll V. Maybe the belt tensioner wheel has a problem, sometimes they get hook up and won't engage the V ... Vacuums

HOW TO REPLACE BELT ON kIRBY cLASSIC 111 vACUM cLEANER?


My husband got home and rescued me! He immediately fixed the problem. ... Vacuums

The Panasonic MC-V7515 has two belts. The local vacuum repair guy says he only has a part number for the drive belt, which is UB-9. How do I find a replacement for the other belt, the one which directly drives the beater bars? By the way, this vacuum has great suction, but otherwise is far inferior to my previous Panasonic vacuums. The cheaper models aren't a good buy--stick with the more expensive models.


... Panasonic MC-V7515 Bagged Upright Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do they re


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=675093\015\012Generic problem for all Vacuums\015\012I have a Hoover self-propelled\015\012Posted by kl ... Vacuums

I can't find replacement belt for little lux (original model bought in 1991). Stamped on back "Model 1673BA". Motor works fine but belt doesn't turn roller any more.


... Electrolux Little Lux Bagged Handheld Vacuum

Broan B1396 Model -- Type A -- belt replacement --replacement procedure & new belt


... Broan-NuTone CV353 Central Vacuum

How do I replace the drive belt on a kirby G4? Actually the belt is already replaced I just need to know how to reattach that front part back onto the main vacuum. HELP


Greetings from GoVacuum,\015\012\015\012Here's a video we shot showing you in detail how to install a belt properly, and how to reattach the head properly. I hope this helps you;\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum

How to replace parts that hold brush on model 1699v bissell pro heat steamer serial no o417130411


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Kirby vacuette belt replacement - Douglas Belt for Aardvarc Busy B Vacuette Kirby H/V


You can find plenty of replacement belts here:http://kirbyhomecare.com/belts4.htmlThis article might also help:http://www.ehow.com/how_6434639_change-belt-kirby-ultimate-series.html ... Douglas Belt for Aardvarc Busy B Vacuette Kirby H/V

I have a Hoover pet cyclonic upright model uh70085. the brush won't spin, I thought maybe the small belt was stretched, I ordered the correct replacement belt and replaced it, I still have slack and the brush won't turn. the floor and brush adjustment seems to be working correctly. Thanks, Tom


... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

Replace the belt on a Eureka contour model 2900 upright vaccum. I just want to see a picture of the way it comes apart. It a almost new and just needs the belt replaced.


I have listed below a link to the owners manual for your model and a link where you can purchase the belt you need. Hope it helps you!Eureka Contour 2900 ... Vacuums

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

I have a Hoover WindTunnel Bagless Vacuum Cleaner, Model #U5753-900, Serial number 110600215585, which I purchased from Loew's on 3/31/07. With it, came a Hoove Slider for hard floor surfaces, Model #S2105, Serial number 050500084989. The Slider strted making a noise--I thought something had been caught in the roller, but discovered, it had not; so I and my husband proceeded to take the Slider apart. I believe one of the belts had come off; but when we took the screws off the bottom to check


... Vacuums

Replace belt and dyson vacuam cleaner, model dc14 I ordered a new belt and brush replacement assembly and we can't seem to understand how to get it apart to change it


If the DC14 has a brush protected aspect i.e. a switch on the front that puts the drive belt off, the drive belt would have to be replaced by a professional repairer as this can't be done at home. \015\012\015\012If the model doesn't have the b ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

I have a Fantom Fury and need to replace the belt. Please tell me how to get into it so the belt can be replaced. It is a Fantom Fury Vacuum Cleaner # 3680093 Fantom Technologies Model # F10051 01


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0889 seconds