Having problems with your Vacuums ?

Rainbow d4se assembly

\015 How to assemble correct movable fan gen.,middle fan spacer,rexair d4 lower stage fan and so on? Which side goes first?\015

Answers :

Generic problem for all Vacuums
\015\012Rainbow d4se assembly
\015\012How to assemble correct movable fan gen., middle fan spacer, rexair d4 lower stage fan and so on? Which side goes first?
\015\012
\015\012I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure.
\015\012You can change the fans on the RexAir / Rainbow vacuum but sometimes that is only a temporary fix, the fans would be new but the rest of the motor may burn out sooner with the added load to the motor and sometimes it is more cost efficient to replace the motor than to repair it and have it break down or burn up the motor, as far as the spacing
\015\012You can refer to the nearest vacuum cleaner dealer in your area or in the yellow pages or call the RexAir/Rainbow factory for a schematic of the breakdown of the motor, and you can also cal the factory or check the website and download the owners manual from the website.
\015\012http://rainbowvacuum.com Customer Service
\015\0121-248-643-7222 Monday thru Friday from 9:00 am to 5:00 pm EST
\015\012Don – The Vac Man
The larger opening of the 2 smaller fans face downward toward the water pan. The larger opening of the larger (center) fan faces upward toward the top fof tuhe canister.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Rainbow d4se assembly


Generic problem for all Vacuums\015\012Rainbow d4se assembly\015\012How to assemble correct movable fan gen., middle fan spacer, rexair d4 lower stage fan and so on? Which side goes first? ... Vacuums

Assembly Where can I find the assembly manual for the Rainbow E Series online?


Can't figure out how to hook up steam cleaner ... Rainbow E series Canister Wet/Dry Vacuum

Instructions for rainbow shampooer assembly; - Rainbow E series Canister Wet/Dry Vacuum


... Rainbow E series Canister Wet/Dry Vacuum

Motor replacement for Rainbow D4se


From the bottom, remove the screws separating the top and the bottom. Then at the bottom, remove the round water seal, take out those screws, ( careful with the water seal, reglue it with contact cement when you put it back on). At the top of the m ... Vacuums

How to reassemble impeller assembly on rainbow D4c model


... Rainbow Vacuums

How to assemble the rainbow aquamate 2 handle


<p><a rel='nofollow' href="http://www.rainvac.com/rainbow-vacuum-schematics">Download the schematics for you model here...</a></p> <p>RainVac </p><p><a rel='nofollow' href="www.rainvac.com">www ... Rainbow E series Canister Wet/Dry Vacuum

I just recieved an old Rainbow D-3 vacuum (1980 's). Everything seems to be properly assembled but water spews from the basin when I turn it on. Suggestions?


Download manual here > http://www.rainvac.com/rainbow-vacuum-manuals ... Vacuums

How to change the power switch on a D4SE Rainbow Vacum


Hi there SmartAlec From NelsonVacuums.com.au here. Ok the switch is a tricky one if you havent done it before but the trick is having the right tool. I assume you have got the machine stripped to that point (phillips head screwdriver is all thats req ... Vacuums

Rainbow E-series Aquamate II connection problem


Well I am not goinmg to call, but you can go to http://www.rainbowsystem.com/manuals/\015\012\015\012And download the manual for your model of Rainbow. ... Rainbow E series Canister Wet/Dry Vacuum

Rainbow SE (1991)


Little fan first, then hour glasss spacer washer side down then larger fan, with spacer sticking throug then small fan. then normal spacer. assambley starting from top part down, your local vacuum cleaner shop should have switches or contact rainbow, ... Rainbow E series Canister Wet/Dry Vacuum

My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum

Diagram for rainbow e series trigger


... Rainbow E series Canister Wet/Dry Vacuum

I have taken delivery of a new Lloytron Halogen Oven E4701 WH.from a supplier in the UK (I live in Spain). On unpacking it I found that Part of the temperature control knob assembly had fallen down inside of the heater body. I dismantled the heater body to retrieve the part but I cannot now work out the order of re-assembling the fan parts so that the fan does not catch on other parts of the assembly. I cannot find a parts drawing on-line. Can you help ?


... Vacuums

My kids were in charge of the Rainbow, but they moved out. My husband surprised me by cleaning a dirty rug. Neither of us know how to use the Rainbow, but I at least know that you're supposed to use water. Will it damage my Rainbow that he did not use any water when he vacuumed?


Your Rainbow might have been damaged. It would be advisable to take the machine to a shop and have them do a cleaning on it. The water is the filter, and there is a separator between the water and the motor. The separator only prevents the water f ... Rainbow E series Canister Wet/Dry Vacuum

My husband took the brush and base assembly apart to clean the unit...when he took the wheel assembly off the small white leveller inside fell off. How do we get this back on??


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Assemble Swivel Assembly onto Kenmore Canister vac


Got this post off this web site...I just replaced my swivel and it worked:\015\012http://www.managemyhome.com/mmh/answers/Answers.action# ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Assembly just bought used vacuum, with no manual. Can't figure out how to assemble handle. help thanks mike


The handle just snaps into place on the top. there is a handle pivot, it goes in that. The bag, put over the exhaust hole on the right side, make sure it locks into place, the bag top will snap into the top part of the handle. ... Kirby Ultimate G Bagged Upright Vacuum

Rainbow vaccum I have a rainbow vaccum and it stopped working. The on and off switch may not be working. I am not sure how to change that switch?


Make sure the bowl has the pin on it. The Vacuum has switch in the bottom that keeps the Vacuum from running if the bowl in not on or the little pin is broken off. \015\012\015\012 \015\012\015\012Ralph Wakeman\015\012\015\0 ... Rainbow 75th Anniversary Canister Vacuum

Dyson DC05 Is it possible to replace the cable in a DC05 cable rewind assembly? I do not appear to be able to remove the spring housing from the rest of the assembly the disk with the cable exit hole seems to be fixed is it removable?


Yes it clips out ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Rainbow d4c How do you take apart the rainbow d4c to change the switch


All four sides of the inner shell in the top can be pushed in to remove inner shell. I tried to take my switch out and gave up after several attempts at pinching the plastic tabs inward that hold it to the case. even with all four tabs pushed in t ... Rainbow 75th Anniversary Canister Vacuum

I was told that the brush assembly(black plastic holders)should be inverted/fliped over when doing maintenance on my orickXL vacuume cleaner? So not to wear out the brush assembly is this correct?


You adjust it to adapt to the wear of your brush. they will make your brush higher or lower since the hole is offset. if you were to install a new brush you would want it as far away from the carpet as possible and vise versa. ... Vacuums

My Rainbow SE vacuum was working fine until I ran over the edge of a rug and it went in to the nozzle. I immediately switched the vacuum off and proceeded to move the rug. When I tried to turn the Rainbow back on the brush was no longer spinning. I've tried the reset button and checking the nozzle for any debris, there are none. The brush just won't spin.


Hello lilbutmunch1,\015\012The brush is motor/belt driven so you probably either broke the belt or it shifted off the motor or brush shaft. I suggest you unplug it,flip it over and look for screws that hold the baseplate together.. remove those ... Rainbow E series Canister Wet/Dry Vacuum

How to maintain up keep on my rainbow vacuum - Rainbow E series Canister Wet/Dry Vacuum


Keep the bottom clean, make sure the rubber seal in the bottom doesn't start to crack and every 10 years or so replace the brushes.\015\012\015\012I wrote a tutorial on how to take apart an E-Series rainbow. \015\012\015\012 ... Rainbow E series Canister Wet/Dry Vacuum

I have a Kirby Generation 3. The handle spring assembly is broke, so I took it apart to get a part number. Can you tell me if there is a cross reference or something on these parts. I am unable to find a part with the same number that is located on the part I took off. The number on this spring assembly shows Kirby HA-670289B K-1. Any help finding this part is appreciated.


... Kirby Vacuums

Assembly I am trying to assemble the eureka smart boss. The problem that I am having is that the handle is not completely fitting into the cleaner body. I can slide the handle into the handle supports but it doesn't seem to click together. There is a space at the top; it doesn't seem to be able to fit as closely as the bottom. Thanks, Lisa


It may not just slide into place, you may have to knocj it into place, then put the screws in to secure it. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0220 seconds