Having problems with your Vacuums ?

My B50 Keurig single cup Brewer works great but this am, I find that the bottom Sharp Needle is gone and I cannot find it. It is the needle that punctures the bottom of the K-Cup. Needle and little rubber piece is gone - DO YOU SELL THIS.


Answers :

Here
in Fixya we don't sell anything, we just give some guidance how to find the
part you need. Also Keurig makes it next to impossible to get parts unless you
have sent in your warranty and even then they want you to send the unit back to
them. Ebay is about the only place you can find anything! Very very expensive
for even for a parts unit. Keurig is very helpful as long as you are signed up
with them.



So
if you are under warranty then you can just contact keurig and they will
replace the whole machine with a new one.



If not then there is a good chance to find what you need using the
email



[email protected]
for Keurig parts.

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My B50 Keurig single cup Brewer works great but this am, I find that the bottom Sharp Needle is gone and I cannot find it. It is the needle that punctures the bottom of the K-Cup. Needle and little rubber piece is gone - DO YOU SELL THIS.


Herein Fixya we don't sell anything, we just give some guidance how to find thepart you need. Also Keurig makes it next to impossible to get parts unless youhave sent in your warranty and even then they want you to send the ... Vacuums

I sucked up a long piece of string, and it rolled around the bottom and smelled like burning. The piece of string is gone, but the motor doesn't sound like its engaging. Is this going to be expensive? Can I do it myself?


Flip the vac over take off the bottom cover plate to expose the belt and see if it still actually on the shaft, more than likely when you tried to run the vac while the string was wrapped around the beaterbar it caused the belt to either snap or stre ... Bissell CleanView II Plus Upright Bagless VacuumVacuum

My Little Green Machine has stopped sucking (second one with this problem!) I have removed the bottom plate and cannot find how to get to the hose to determine if there is a blockage. How do I do this? There is a screw that seems to hold a piece in place but it does not come out to get access to the hose.


Remanufacturing is a big problem since we don't know what was changed and how. ... Bissell Vacuums

The bearing mounted gear/cutter assembly at the bottom of my 6 month old GE 169188 blender has gone bad; it's very loose and leaks fluid. The part is easily replaced. Only problem is that I can't find the part anywhere I've looked online. What is the deal? Why dont they make such a simple part available for a nearly new cheap appliance????


Cannot find that model number.. However.. Contact GE parts and service.. here.. https://www.geapplianceparts.com/GEApplia ... Vacuums

I have a brother ls 590 sewing machine, and i cant find the right tenchion for thin stretch fabrics. my fabric keeps getting caught underneath the needle where the bottom thread comes out. can you give me some tips, and tell me why this is happining.


... Vacuums

ComWould it be possible to get a new manual for this model #2961 I recently moved and lost the manual. I need to find the part number for the bottom filter and and the top rubber piece to replace for today at the store


... Eureka 2961AVZ Bagless Upright Vacuum

I have a Dyson DC-17 and the top of the cyclone has hair and other debris jammed in the ports. It has 6 six screws holding the parts together and I can only get access to 4 of the screws. The bottom piece appears to be removable, but I can't figure out how to remove it without damaging it. If I can get this piece off, then I have access to the other 2 screws. Can you tell me how to remove the bottom piece? Thanks in advance.


The instructions on how to dis-assemble your DC-17 are somewhat lengthy and it is quite helpful to have pictures and videos handy while you are doing it. Normally I would give the instructions here, but due to the amount of info that is necessary to ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I can't find the 4 screws to get to the belt on a dirt devil 22.0 Fx. The bottom of the vaccuum says " remove four screws from bottom of nozzle then lift top nozzle cover off", where are these screws, I can only find two, and which is the top nozzle cover?


... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

I broke the handle part of the shark steamer #53101. I don't have the book to try to tell you the parts I need. Can you send me a picture or a copy of the steamer. It is purple. The above number may not be the correct one. It is broken in the center part. It has a little small circular piece that joins the two pieces which are broken. The beginning of the handle at the bottom of the steamer and the next session which has the steam release. The top of the handle is okay . It the middle and bottom


Hi,Ann there are very few parts for these...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Hoover steamvac F7226900. Bottom of clean fill tank cracked, how do I take off the black plastic piece around the bottom of the tank without breaking it? Thanks!


Try this link belowhttp://www.ereplacementparts.com/hoover-f7226900-steamvac-parts-c-37315_37419_202371.html ... Vacuums

Pfaff creative 1475 cd - Broke a needle now the thing the bobbin goes in won't spin and the manual wheel doesn't twist either. I think the tip of the broken needle has it jammed. How can I take that assembly off to find and free the broken needle tip?


... Vacuums

Sears progression kenmore canister va. Model 11623612300 on the wand, the plastic piece broke off, there is one long wand with two piece to it well the plastic piece, not on the bottom, where it hooks into the beater bar thing, but the other plastic in the middle. Can this be replaces?


Hi.The part is probably available as replacement.Please click here ... Kenmore Vacuums

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems


Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

Kenmore Progressive Model 116 35922500 - bottom piece back on?


... Kenmore Vacuums

How to remove the hinged plastic piece at the bottom of the bag?


... Oreck XL Ultra Bagged Upright Vacuum

Dyson curved piece at bottom keeps falling off how to reinstall?


Call me, doug in Riverside cali, pretty handy just rebuilt my stage 3 on my animal. I am incredibly gifted. 951-316-7071 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I would like to know how i get the very bottom piece off my vacuum off so I can put a new fidder hose on it? The hose is black and it is only about six inches long. its lacation is on the very end of the vacuum but between the end and the piece that gos along on the floor.


You don't have to take the vacuum apart.\015\012Assuming this is an Epic 3500 or similar upright Electrolux:\015\0121. Lay vacuum on it's side.\015\0122. Gently pull hose from power head. It's not screwed in so that should be eas ... Electrolux Epic 3500 Vacuum

Broken piece The black plastic octagonal end of the brushroll has broken off the brushroll, so the brushroll won't stay in place. Can I get another little piece to attach onto the brushroll? Or do I have to get an entire new brushroll? And if so, do they sell replacement brushrolls? CP


You will have to replace the brush roll, part #60844-5, belt # 61120B. You should be able to get them from a repair shop, get the right one or it won't work right. You maybe able to go eureka.com and order direct. ... Eureka 4700A Maxima Bagless Upright Vacuum

On a filter queen 360 vaccum the electrical connection from the hose to the wand was loose and over time the electrical arcing burned up the female conector piece. Is there any way I can replace this without having to buy a new hose! Where would I find this female conector piece.


I am having the same problem On a filter queen 360 vaccum the electrical connection from the hose to the wand was loose and over time the electrical arcing burned up the female conector piece. This sounds to me like a manufac ... Filter Queen Vacuums

Circuit board i have searched far and wide looking for a circuit board for my fantom cyclone xt, so far i can't find one .. is their anyone who can can locate or sell me one of these hard to find items. i am at the end of my rope ! any help is appreciated, thank you for your time TOO SLIM


Http://www.vacmall.com/supplies.asp?Brand=Fantom&Model=Cyclone+XT ... Fantom Vacums Cyclone XT Upright Vacuum

Bissell - Model 1697 - Powersteamer Pro - Carpet Cleaner I took the unit apart to replace some broken pieces and I can not seat the bottom to the top without properly engaging the soap/water mixer. What is the proper assembly procedure. What is the orientation of the water/soap mix valve when I seat the top to the bottom? The soap/water mix valve needs to engage the knob screw threads but this assembly is a blind operation. Do I turn to the soap/water mix knob to water only then seat the


Hi,\015\012http://dl.owneriq.net/7/7e477b7e-4440-49cf-a219-b68d301549e3.pdf\015\012This diagram will help you see the diagram plus the part assembly no and place it accordingly.I have also given link for Bissell - Model ... Vacuums

Hi - I have a sinkmaster premium special edition 3/4 horsepower which seems to have slowed down and the water is just sitting in the sink. I have tried to find a red button on the bottom to see whether pressing it will unclog the system but can't find it. Can someone help?


... Vacuums

Broken Elevator? One side of my brush will not stay up. Could this be a broken elevator? I think the elevator (black piece) has fallen into the machine. How do I get into the bottom to get the piece out and repair/replace it?


Asdasd ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Cracked On the bottom of my vacuum, the area around the belt housing is cracked. It looks as though the whole plastic bottom piece would have to be replaced just because of the crack.


I'm afraid that you will have to replace the base unit, part #62577, would sell for around $25. Once it cracks, then it is weak and will affect the brush roll and belt. ... Eureka 2996AVZ Bagless Upright Vacuum

I am trying to find the powermate parts to replace the roller brush on this vac I have trouble finding websites that sell these. I need to know the item numbers so that I can order the correct items to fit this model.


Brought the powermate part to local Sears part store and they ordered the items we needed \015\012 thanks for trying to help \015\012\015\012GFreckles913/Glenna Rodell ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0390 seconds