Having problems with your Vacuums ?

I have a Hoover U5753-960 upright, I need a new on of switch for it.

Answers :

\015\012Generic problem for all Vacuums
\015\012I have a Hoover U5753-960 Upright
\015\012Posted by amoser on Apr 23, 2008
\015\012I have a Hoover U5753-960 upright, I need a new on of switch for it.
\015\012I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure.
\015\012You can try a couple of places, 1st try your local vacuum cleaner dealer in your area, you can find him in the yellow pages, or 2nd, you can call the Hoover Co @ the phone # listed below or look up the Hoover website also listed.
\015\012http://www.hoover.com Telephone
\015\012Contact our Customer Service Department at 1.330.499.9499
\015\012Monday through Friday
8 a.m. - 7 p.m. EST

\015\012Thanks, Don – The Vac Man
\015\012Go Ahead. Use Us.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Hoover U5753-960 upright, I need a new on of switch for it.

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=539049\015\012Generic problem for all Vacuums\015\012I have a Hoover U5753-960 Upright\015\012Posted by amoser o ... Vacuums

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga

I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

Hi The band snapped the other day on my Vax Swift Turbo upright hoover and i got a new band from a Hoover repair centre. (Im assuming the bloke sold me the correct band). Was tight to go on. And it seemed ok. However, after switching on the band snapped immediately. Kinda burnt as well (at the point it snapped). Any ideas as to what the problem is here? The hoover is roughly 2 years old and used around 3 times per week. thanks Mike

Sounds like the brush roll is bad. Did you check the ends to make sure they turn freely? If not, replace it. ... Vacuums

Need new filter model#u5162 900 - Hoover Fold Away U5162-900 Bagless Upright Vacuum

If you go to hoover.com you can order a new filter from there. the part num. is 43613026. this filter will fit the fold-away. ... Hoover Fold Away U5162-900 Bagless Upright Vacuum

Hoover steamvac f6020-900 leaks water with switch off and in upright position, can't find the leak in either clean or dirty water tank. also need a owner/maintenance manual.

... Hoover F6020-900 SteamVac Upright Vacuum

My girlfriend has a Hoover upright vacuum, Mdl. # U4645-930. I need a belt for the brush and a new bulb and am having trouble finding the correct part numbers so I can pick one up locally. Can you help?

I checked with Hoover and they said the part number for the belt is #38528040, for the bulb #27313101, and they also included a part number for something called an agitator #48414081. Not sure if this is required to replace one of the other parts. ... Hoover Windtunnel Turbo Power U4645-930 Vacuum

I need to change the small belt - Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Just remove the cover on the bottom of the vacuum by loosening the screws holding it on. Once they are off, you'll be able to slide out the rotating brush, and you'll see the belt there. Look inside the vacuum also, as when they break, they can sprin ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.

Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums

Hoover Upright Bagless WindTunnel does not self propel (U6625-900). Belts are new, Brush turns strongly. Wheels propel forward very weakly and do not reverse when the handle is pulled backward. Is there a mechanical link from the self propel switch to the "transmission" ? Are there any gears that could be worn or not engaging properly?

... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Vaccum cleaner, (hoover upright) needs new belt, but i can't figure out where it's located.....yes, i'm a woman...lol thank you..

Turn Vac over, remove the plate covering the brush roll, then you can get to the belt and brushroll. ... Vacuums

I need to replace the idler arm assembly on a U6439-900 hoover wind tunner upright. I have the clear cover completely removed but still do not see how to remove old and insert new assembly.

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Need to replace motor on a Simplicity upright vacuum and need help with the wiring the new motor. New motor is different from old one.

You might not have the right motor. Take the old one with you because it should go right back in as easy it was to remove. ... Vacuums

I have the new power on/off switch to replace the old one(Rainbow vacuum). However the new switch has 4 contacts & the old one has 6. Need wiring diagram.

Simply pair 1 each of the power head leads and motor leads on to one terminal and wire the cord as on previous switch. ... Rainbow E series Canister Wet/Dry Vacuum

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,

You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

Hoover Alpina 2 1300 cleaner. I need to split the upper and lower casings to check that the switch is working. I have removed the screwa in the area around the bag, but now need to remove the switch and cable rewind covers, as I assume there are more securing screws under them. Can you advise how to do it please?

Move covers (forcibly !) away from the centreline of cleaner then move to rear until released. The covers are held by slide catches on inner edges. ... Vacuums

Hoover Upright Vacuum model U5470-900 - The On/Off switch on the handle does not properly engage the power switch deeper in the handle assembly. It appears to ride over the lower switch and doesn't engage it to operate it. If I play with it, I can get it to maybe turn on the vacuum, but, then the upper handle switch won't turn it off. Our current workaround is to use the power cord for on/off operation.

... Hoover Vacuums

What's your problem?I have to replace the power switch on my Hoover U6485-900. What part do I need to orer? Wher can I order it?

... Hoover U6485900 Bagged Upright Vacuum

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v

I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Hoover upright 2000w, HL2005 001 problems:the hoover made a pop sound & turned off. Tried leaving it for 30 mins as suggested in the manual but it still won turn on. Really cannot afford to buy a new 1 & would like to fix it. partner is an electrician so if we have some guidance as to what the problem may be i am confident we can fix it. the hoover is only 18 months old so not very old at all.

... Vacuums

Hello! I have a Rainbow vacuum Model# D4C that needs a switch. I am only able to get the new style 4 wire switch and it has the 6 wire. Can I make the 4 wire switch work in place of the 6 wire?

... Vacuums

Eureka Vacuum Excalibur Model 6975A on/off switch won't turn off. Probably need new switch but can't figure out how to get cover off to get at switch

... Vacuums

Need new motor for "WAP ST20" hoover

... Wap 28538 Wet/Dry Vacuum

Need new switch for Shopvac QSP Pro 10 gallon unit

I just went through the same problem with a Shop Vac. The switch is easy to replace but not easy to find. After removing the switch, I found a match made by Sigma Switches. They directed me to contact a local RV dealer and look in either their Coa ... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

I took a defective switch out of my xl2. I need to know hwere I can buy a new switch

Easiest solution will be to go to an authorized Oreck shop. Next best bet may be any vac shop. Third option is online, but likely they don't want to sell it you, but have you take it to an authorized dealer for liability reasons. ... Oreck XL2600 Vacuum

My hoover vacuum runs for about 10-15 minutes then the saftey feature shuts it off(overheat?). i have taking it apart a cleaned it with no results, added new bag also. after an hour it cools down and works again. do i just need a new vacuum?

Do you have suction through the tools? Does it look like it picks up when it runs? The machine could be clogged and that would cause the problem, but unfortunately the sensor that shuts the machine off could be bad if the machine isnt clogged. Its no ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1642 seconds