Having problems with your Vacuums ?

How do i replace the fan blade assembly which are broken in my ureka model the boss thank you lorne

Answers :

\015\012Generic problem for all Vacuums
\015\012How do i replace the
\015\012Posted by lmurray1 on Apr 23, 2008
\015\012How do i replace the fan blade assembly which are broken in my eureka model the boss
thank you
\015\012I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure.
\015\012There are 2 different models of the boss by Eureka – there is a standard old style upright that the belt that the belt would unscrew from the bottom of the motor and you would have to remove the top of the vacuum cover to remove the main motor and gasket assm, and then the fan has a reverse thread on the plastic fan and you would unscrew the fan after removing the belt pulley. Then you would screw on the new fan, belt pulley, replace the gasket and re-install the motor. If you have a new style with a side mount motor you would remove the top cover, the motor would be in there sideways, un-screw the motor, remove the silver tape around the fan housing and un-screw the fan housing – same as above un-screw the fan from the motor, there is a nut on the end of the fan holding that on – (remember, the fan has a reverse thread) re-install the fan. Then the fan housing, replace the silver tape, and then screw down the motor and replace the top cover, then you can test. As always free to contact your local vacuum dealer in your area in the yellow pages or contact your Eureka factory manufacturer listed below:
\015\012http://www.eureka.com Customer Service Phone Number
\015\0121-800-282-2886 Hours of Operation
\015\012Monday thru Friday 8:00 am to 7:30 pm CST
\015\012Saturday and Sunday 10:00 am to 6:30 pm CST
\015\012Thanks, Don – The Vac Man
\015\012Go Ahead. Use Us.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do i replace the fan blade assembly which are broken in my ureka model the boss thank you lorne

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=540001\015\012 \015\012Generic problem for all Vacuums\015\012How do i replace the\015\012 ... Vacuums

I need to purchase new blades for our 52" Jericho IV ceiling fan, Model 166315. I went to home depot in Harrisville, UT and they said that we would have to contact you and they didn't have ANY replacement fan blades in stock. HOW COULD THAT BE WHEN THEY HAVE HAMPTON BAY FANS ALL OVER THEIR LIGHTING SECTION? What kind of a business are you running when one can't get replacement parts? Our fan is making noise and I want to replace the blades. How hard can that be? By-the- way; I hope you no

... Vacuums

Hi On a Hoover convertable model U4497-900 I'm trying to replace the fan. The old fan cracked, then flew apart. I have the new fan, have the motor assembly removed, but can't seem to get the pulley nut off the motor to replace the fan. Is there a trick to this or should I just try to muscle it? Thanks.

... Vacuums

Broken fan need a repair man or service centre. If not a replacement fan for self repair. I live on the Gold Coast Ray is my name. Kirby Legend 1 model 2HE

Http://www.ultimatesanitarysupply.com/pdfs/VacuumMaintenance.pdf\015\012\015\012see the link ... Kirby Vacuums

I need to replace the fan blades on a Kirby Heritage II, Model 2HD, vacuum cleaner. How do I remove the drive shaft that the fan is mounted on? Thanks, Robert Croft

... Vacuums

The top blades of the dasher of my Rival 4-quart electric ice cream maker (model #8704) are broken. I need to replace this part. I couldn't find this model on the website or any site from which I could order this part. Can you help me?

Hello,The part for your ice cream maker is not available any where online. The best thing you can do is to contact the manufacturer and ask them where you can get the part. They might have dealers who sell the parts.You can ca ... Vacuums

I have 2 wahl hair clippers (homecut) I require size 6 comb and size 9 comb the model No is 441-3411 and 441/0359 has the base plate blade broken, Where can I source past and replacement base plate blade

... Vacuums

Bissell - Model 1697 - Powersteamer Pro - Carpet Cleaner I took the unit apart to replace some broken pieces and I can not seat the bottom to the top without properly engaging the soap/water mixer. What is the proper assembly procedure. What is the orientation of the water/soap mix valve when I seat the top to the bottom? The soap/water mix valve needs to engage the knob screw threads but this assembly is a blind operation. Do I turn to the soap/water mix knob to water only then seat the

Hi,\015\012http://dl.owneriq.net/7/7e477b7e-4440-49cf-a219-b68d301549e3.pdf\015\012This diagram will help you see the diagram plus the part assembly no and place it accordingly.I have also given link for Bissell - Model ... Vacuums

Need to replace impeller fan on Classic III. Half the blades are broken off. I can't figure out how to remove it. I have taken cover off.

... Kirby Vacuums

The bottom lamp shade of my fan is broken,model #54wdl, how do i get a replacement

... Vacuums

Fan blade is broken in half on my sanitaire upright I have the replacement but cant get the old one off

... Eureka Sanitaire SC4570 Bagged Upright Vacuum

Sanitaire Model S661 Type A, heavy duty commercial motor, 8840 watts. A large nail was accidentally vacuumed. There was immediate noise, and then it smelled like smoke. We can see after removing the bottom plate that the translucent plastic fan was completely broken. Can it be replaced? We have no repair service nearby.

... Eureka Sanitaire S661 Bagged Upright Vacuum

Fan replacement I found the part to replace my broken fan. I've remove many screws, but I can't remove, what seems to be, the obvious plate to get to the broken fan.

Http://reviews.ebay.com/KIRBY-VACUUM-REPAIR-HOW-TO-REPLACE-THE-FAN-IMP ... Kirby Ultimate G Bagged Upright Vacuum

Fan replacement I have to replace the fan on my g4 how do I get the old fan that is worn and broken off the shaft,,thanks for any help that you might be able to give

Detailed instructions on fan replacement HEREGoodLuck,Rocky:-) ... Kirby G4 Bagged Upright Vacuum

How do I attach the replacement blade on my B&D jigsaw model 7504? I have the replacement blade but don't know how to attach it....

Locate the small hole with the screw inside it directly above the handle, which usually is in line with the blade. Loosen the screw with a flathead screwdriver. Once the screw is loose, gently pull the blade out from the unit .. this works with ... Black & Decker Vacuums

The top front corner of the rake assembly on our Littermaid Mega box is broken off. Where and/or how can we get a replacement assembly to fix this. Because the piece is broken off, the "wheels" on that side do not like to stay in the rail and the rake doesn't work properly.

... Vacuums

The fan on my Dirt Devil model 103 hand held vac cracked. I bought what was designated as the correct replacement fan but the hole in the center of the fan is a lot smaller than the shaft that it has

... Vacuums

During re-assembly of my conair (model HC91RS) i noticed that my two blades do not line back up. The big blade sits evenly in it's space but the small blade is tilted slightly to one side. Is there any other means of aligning these two blades?

... Vacuums

I have their Margarita OASIS model MOS-400 series. I got it for Christmas two years ago and now the blade in the ice tray is dull and even small bits of ice will not get shaved. Is there a way to replace the part or to sharpen the blade.

... Vacuums

I have a cooling fan on my wine cooler that burnt out, I need a replacement. I need a Heng Shan Fan model no# FS92252M 12v 0.2 amp

... Vacuums

The belt is broken on our Hoover Allergen Filtration Model U5018-900 120 v. 60 Hz 12.0 A. Belt 38528040. Where can I get the belt and instructions on how to replace the broken belt?

The owner's manual can be downloaded here (in red, "Download the Instruction Manual (PDF))\015\012http://www.hoover.com/product.aspx?model=U501 ... Hoover U5018-900 Bagged Upright Vacuum

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

I have a Hampton Bay Midili fan which I just installed about a month ago and it was working fine. A few days ago when I flipped the switch on the light flickered on and off consistently until I turned the switch off. The remote also stopped working to control the fan and light. Since this model only can be controlled by the remote I am worried I will have to replace the remote already after only 1 month!

In many of these remote controlled lamps you cant use the new spiral light bulbs .. you can only use standard incandescent lights .. if thats not the trouble then you may indeed have a bad controller (in the fan) .. there is probably at least a 90 d ... Vacuums

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?

First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

Replace belt and dyson vacuam cleaner, model dc14 I ordered a new belt and brush replacement assembly and we can't seem to understand how to get it apart to change it

If the DC14 has a brush protected aspect i.e. a switch on the front that puts the drive belt off, the drive belt would have to be replaced by a professional repairer as this can't be done at home. \015\012\015\012If the model doesn't have the b ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1126 seconds