Having problems with your Vacuums ?

We have a Everstar Turbo Vac. 180 and so far its been wonderful.. All of a sudden it became really loud and spitted out the debree. took it to a vac. repair shop and he wouldnt even look at it! Any suggestions?

Answers :

I found my Everstar near a neighbor's trash. I was going to look for another vacuum cleaner for my third level so I wouldn't have to drag my heavy cleaner up and down the stairs. I was totally and pleasantly surprised at this vaccuum cleaner. It had better suction than my dyson. Granted it is kind of a pain to pull out the dirt from the plastic canister but I got used to it. Then one day it just stopped. I know that when the Dyson stops it means something is stuck or clogged and you have to wait for the motor to cool down for it to start again. Same thing happened to the Everstar. It started again. I took the top part where the filter was and found the filter to be incredibly filthy. I washed it, dryed it and put it back and that was the cause of the problem.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a Everstar Turbo Vac. 180 and so far its been wonderful.. All of a sudden it became really loud and spitted out the debree. took it to a vac. repair shop and he wouldnt even look at it! Any suggestions?

I found my Everstar near a neighbor's trash. I was going to look for another vacuum cleaner for my third level so I wouldn't have to drag my heavy cleaner up and down the stairs. I was totally and pleasantly surprised at this vaccuum cleaner. It h ... Vacuums

My Shop Vac Series H87 will not power on. It is empty and the filter's clean. I looked under the troubleshooting section of www.shopvac.ca for instruction. They advised to hit the reset/breaker button. However, I don't know where to find that switch. Any suggestions? Thanks! -Spence

... Shop Vac 925-13 Canister Wet/Dry Vacuum

Repair manual for shop vac 87719-17 - Shop Vac Vacuums

... Shop Vac Vacuums

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless

Get over it and buy a new one!!! ... Vacuums

I have a ten year old M+S central vac. it shuts off after about 5 min of use. They came out and took the unit to their shop. I dont have the model #.repair shop says I need a new motor but it runs. what can I tell them?

... M&S Systems FX-3000 Bagged Central System Vacuum

Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and

Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I had a real heck of a time with the bag installation, because after the pop i zipped it up and started to use it and then the bag of the vac, not the replaceable bag fell off and i kept putting it back on but it kept falling off and when i looked inside the bag to reattach it to the vac cleaner i noticed that the dust was all inside. i haven't even used it that much as i keep it to do the upstairs bedroom only. i love that it is so lightweight and easy to use and i hope that someone can co

Mary, I have some wonderful news for you and your Oreck XL2600 Vacuum, I called 1 800 989 3535 customer service and inquired about your bag attach problem, it seems to be a docking station problem that "may" be warranteed, however if it is missing ... Oreck XL2600 Vacuum

My shop vac stopped working while vacuuming i looked at everything i could look at and still wont work tried several other outlets checked cable still nothing

Staring from the failrue of the power cord,the main plug,t he main switch each of the sections must be tested for continutiy before we can conclude.\012SInce it is clear case of power failure the voltage must reach the motor,if not back trace t ... Shop Vac Vacuums

My Shop-Vac 5870400 was working just fine, and then one day while i vac the floor its just stop working, tried to turn on/off a few times, swicth to different outlet. i did even tried to open it, but found no burn or anything that suspicious. i never drop nor used outside, only inside the house for normal vacumm. please help. thanks.

Same thing just happened to mine. My solution is to get another one but a different brand. I think it should have lasted longer than four years of fairly light usage. From what I read, if it does as we both described, the motor is shot and not wor ... Shop Vac 587-04-00 Canister Wet/Dry Vacuum

I have owned 4 sebo uprite vacs. Every one of them has the same problem. Where the handle connects to the vac it break contact and shuts off and on. It seems the connection between these two parts is very weak. The only answer I get from my local repair shop is

Well you now know the error of your ways, don't buy another!The best fix is to remove the connectors and connect the wires directly together. ... Century 400 UVAC Vacuum

DC15 Vac comes on but the head will nmot come on. Local Vac shop said circuit board was burn up,can I repair myself. where do I get parts

HighnTools had posted this solution - try it.\015\012\015\012I \015\012have finally fixed my sister's dyson dc 15 beater bar problem. It was just 2 tiny broken wires \015\012connect to circuit board lead to the beater bar ... Dyson Ball HEPA Upright Bagless Vacuum - Iron/Satin Yellow

Just bought a 5 gallon shop vac the casters dont look like they fit the holes are small the casters have a nob on the end that doesnt look like it would fit unless you pound it in and i dont think thats right what do i do?

... Shop Vac 925-13 Canister Wet/Dry Vacuum

Shop vac my craftsman vac is blowing dust out the difuser filter. Have cleaned the filters out. Any other suggestions?

Vacuum is less than a year old and died in the middle of a use. No power... tried to plug it into 3 known, good outlets. Suggestions? ... Craftsman 17765 Canister Wet/Dry Vacuum

Shop vac sucks water for a few seconds then it spits it back out

Don't use the paper filter for sucking water. It can ruin it. It will still be usable if you just set it out to dry but there is no reason to use it for water in my experience. I have a sears shop vac and it will fill up more than half full without e ... Shop Vac 925-13 Canister Wet/Dry Vacuum

Looking for a replacement canister Shop Vac 2010 1x1

... Shop Vac 201-15-00 Handheld Vacuum

My Shop Vac QAS60 stopped working while I was using it. Is there anything I can check and/or repair on my own?

... Vacuums

Over heating? My 10 gallon 4HP shop vac has started shutting off after about 30 sec. after I turn it on to use. It smells real hot after I shut it off. I have changed the filter and the bag, which did not solve the problem. Any suggestions on what the problem could be? It's only about 31/2 years old and I really don't use it all that much, mainly for getting up dust and cob-webs from my garage.

It sounds like you need to replace the motor in it . thank you for using fixya ... Shop Vac ShopVac 3 HP 2 Stage 10 Gallon--Automotive Wet/Dry Vacuum Vacuum

My dyson dc 07 brush will not rotate. I have cleaned all hair and debris from around the brush and no change. I can not even figure out how to look and see if the belt is still attached. Suggestions?

DC07s are not easy to check the belt on, in fact depending on which exact model you have there are probably two belts.\015\012One connects the output of the motor to the clutch mechanism (one end of which has the control knob that ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The brush is not moving on the vaccume. I'm pretty sure that the belt is busted. I cannot see how to get the shroud off, so that I can get to the roller and belt. It all looks and feels like one piece, even when I start removing screws. It is a bag-less vac. The model number is - v1310rs. Thank you.

I know on my Eureka I had to remove a couple of screws on the bottom and then get a flat blade screwdriver and wedge it on each side of the base kinda next where the end of the roller would be and it snaps up and off. Really weird I thought but that' ... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

Hoover bagless cannister 3765 - belt on power head slips off spindle. bought new belts - same problem. is this a design problem or can it be fixed? I don't want to take it to a repair shop 100 miles away and have them just put on a new belt. saw idea of smaller belt - what number? couldn't find suggested royal 104425001 belt.

I would not recommend a smaller belt. You will only wear the motor. This model series power nozzle needs to have a metal clip installed near the belt on the brush roller housing. I know that most of them left the factory without it. Remove the cover ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Electrolux Genesis 1572F: 1) One of the two spring/clips/whatever that hold the upright upright for storage has busted. What is the part called? Where might I find a spare? Or should I go to a machine shop? 2) The power cord retainer thingy on the back of the handle grip has broken; any idea about part#, name of part, where to look? (I can't find a manual or whatever, exploded parts diagram, etc., online. I guess this is the planned obsolescence thing--after all, the machine is hardly even 2

... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Trying to remove a hose from my wet/dry shop vac model 338179370? Any suggestions.

... Craftsman 9-17765 12 Gallon Wet/Dry Vac, 5.0 Peak HP

Took my Miele Solaris canister vac in for repair as it wouldn't turn on. The repairman said to come back the next day for the estimate. I called and he said I needed a new cord reel and it would be $189. I drove to his shop and said I would wait to do it later, that I wasn't ready to spend that much. When I came home, it started right up but has no power and doesn't sound right, the noise of the motor is real soft, not as loud as before. I have this terrible feeling that when we decided not to

When you say 'has no power' do you mean , no suction? He may have left the suction hose of the motor and that's why it sounds different. I would call him back and request that he put the machine back to it's original 'state' as it was when you brough ... Vacuums

Shop vac repair will not start craftsman 12 gallon - one of my guys changed the filter but did not put the screw back on cleaned it out but now it won't start

Did you/they open the main (motor) casing? If so, check to see if there is a loose wiring connection that was missed before closing it up. ... Vacuums

Where would I look to find a clasp/fastener for the top of cannister shop vac?

Just on the edge of the cover. Pretend like you are picking it up ... that edge. ... Shop Vac 960-97-10 Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0593 seconds