Having problems with your Vacuums ?

How do you get cover off dyson dco7 to replace electrical cord?...I can get the torx screw out, but the cover seems awfully tight and I don't want to break the cover

Answers :

I would use a toilet plunger.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you get cover off dyson dco7 to replace electrical cord?...I can get the torx screw out, but the cover seems awfully tight and I don't want to break the cover

I would use a toilet plunger. ... Vacuums

The brushes won't turn. I want to fix it myself but can't figure out how to get to the drive mechanism, by taking the top cover off. I have all the screws out but it seems to have some snap fits holdi

If you turn the vacuum over and are able to turn the brush by hand and it won't turn while its running, then your belt has broken. ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

I need to remove the top cover from a Wertheim w4030, I have removed all screws that I can get at. I have notice a further 3 in places that is not possible to access. It looks as though the two buttons on the top if removed will provide the solution but I don't want to break anything by forcing something that is not supposed to be done. Can you help?

... Vacuums

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac

On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have Sharp vacuum cleaner Model EC-8400C-A. It is not working and I want to remove the cover so that I can fix the problem. I do not want to break to casing as there are no screws just some hidden clips. Please guide me. Thanks

... Sharp EC-6312P Bagged Canister Vacuum

Vacum I need to check the brushes in the motor smells have removed four screws but the cover is not coming off. I dont want to damage this by forcing it but cannot find any other screws Thanks fairweather

Hi there!\015\012\015\012It would certainly help if you said which model it was.\015\012\015\012I can only give generic help now, and do the best I can for you.\015\012\015\012Most plastic products rely heavily on ... Vacuums

I have a progressive 360 model 116.27814. I want to change the exhaust filter and I cannot get the filter cover off of the back of the canister. Please give detailed instructions. I am afraid that I will break the cover, because I can't see how it should detach.

There should be tabs that need to be pressed in, and will allow the filter cover to be removed to access the filter. On some models, the tabs are accessed from the bottom by tilting the unit on its side, or by simply pressing them in from the top, th ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Wispertone 116.29429990 I need help in getting the cover off. The foot retractor pedal for the power cord has screws under it and I am afraid of breaking the it. How do I access the screws under the pedal?

The pedal may be tough but the attached pushrod that disengages the power cord reel ratchet may not be, and is stressed by reddevil6's maneuver. I'd prefer to go after the tabs that retain the pedal's forward end. They are part of the rear cover and ... Kenmore 23313 Whispertone Bagged Canister Vacuum

I have a DC 15 Dyson Ball Vacuum. I've removed and cleaned the filter. I can't get the lid to close properly. I don't want to force it and break something. There is some kind of a red spring loaded tab that seems to be in the way. How do I reseal the top of the vacuum?

The red tab doesn't let the lid close if the filter is not fitted correctly or the wrong filter is fitted. Many after-market filters cause this problem. \015\012\015\012Have you recently fitted a new after-market filter? ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

How did you remove the top cover to get at the arm for the cable drive? (I don't want to break anything else!)

Turn it over, remove the plate over the brush roll, remove the cover over the intake hose, then there are 2 screws, one on each site, remove them, then using a flat blade, there is a slot on each side, from the bottom, push it in to release it and th ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How do I remove the battery in a Dustbuster chv1400 for replacement? I have removed the two screws and removed the cover, but I'm unable to figure out the retaining clips for the battery. Of course I don't want to break the clips.

That model looks similar to my DB200. Instead of the screws, the underside has a latch/panel that you remove. Place a screwdriver in the two slot-like holes that face each other (one at a time) and the 'door' should pop out. Mine was a little stiff ... Black & Decker Vacuums

I can't find the 4 screws to get to the belt on a dirt devil 22.0 Fx. The bottom of the vaccuum says " remove four screws from bottom of nozzle then lift top nozzle cover off", where are these screws, I can only find two, and which is the top nozzle cover?

... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Eureka TRUE HEPA Whirlwind Bagless same problem seems...roller just stopped...took everything apart and turned it on just in time to see belt melt...I was able to get the end caps off both sides at first and now can't seem to get the one side. Really love this vacuum! Don't want to have to part with it!

If you are able to remove one end cap, the brush roller shaft can be removed and the other bearing is exposed for examination and removal of the hair that probably is clogging it. After cleaning and reassembly the brush roller should rotate freely. C ... Eureka 2961AVZ Bagless Upright Vacuum

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?

Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.

Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

My vacuum cleaner is making a loud squealing sound when I turn it on and the brush is turning. It gets louder while vacuuming the carpet. I tried to remove the bottom cover to see inside but, took out a bunch of screws and couldn't get the cover off.

... Kenmore Progressive Direct Drive 30912 Vacuum

I have a window fan with two fans in it & I cannot get the cover or back off so I can clean it. I* have taken all the screws out that I can get to , but there are two clamps that I can't get off, I'm not sure why the clamps are there but they are on the side with the accordian extention. Please tell me how to get it apart - after 2 years it is really filthy!! Thank you, Janet

Remove all the screws, pry clips off that hold on the extensions, than fan will pull apart. The clips must be pried off. They will not break. Then remove screws holding in the fans and remove them as well. Fairly simple process. ... Vacuums

How to dismantle a Miele S 5980 vacuum cleaner. The RESET switch has fallen in and I can't remove the plastic panel to replace it. Neither can I remove the cleaner body to get in from beneath. I have removed 2 screws from the front of the barrel (nozzle end), one screw centre front, two screws towards rear, but there seems to be something else holding the housing together. [email protected]

... Miele Vacuums

Chain tensioner Is it possible to change the chain tensioner of the Husqvarna 240 to a tool less chain tensioner or at least to the chain tensioner where the adjustment screw is accessed from the side not from the front. The problem is that there is a little plastic part that breaks rendering the chain tensioner useless. I have changed it twice and it keeps breaking. To change it you have to change the whole part that covers the break and chain mechanism.

... Husqvarna DMS 240 Core Rig - DMS 240 w/ Vacuum Pump

Bisell Healthy home vacuum stopped working. The troubleshooting guide said there could be a problem in the connection at the handle. None of the phillips screwdrivers we have seem to work in removing the screw that holds the handle to the vacuum. What size phillips screw driver should we be using? If the screw is stripped, how can we get it out to replace it since it is not easily accessible in the handle?

You should use a p2 size phillips. there is only one screw right in the center that holds the handle assy on. frequently that screw backs out and allows the handle to slide back and loose connection. make sure the handle is tightly pressed in and the ... Vacuums

Roomba Discovery Roomba is fully charged and cleaned with sensor wiped clean. When turned on it it sounds normal and commences to go, but it then acts like it is putting on the breaks, spins, tries to go and manages a short distance and breaks again, just not making any progress because it keeps breaking after a foot or so and turns and tries again. Sometimes is gets so stuck from moving forward at all, like it is stuck in one spot just trying to go while seemingly surrounded by barriers. Somet

I had the same back-up, turn, move forward a couple inches, backup-up, etc. problem. Try cleaning/cutting the hair, etc. out from around the brushes, as well as around the ends of the brushes. Also, try a Q-tip to clean out the four pair of sensors ... Roomba Robotic Floor Bagless Vacuum

Power cord Cord is just all knotted a twisted, i bought a rubber cord and just want to replace the original. I have removed all the screws from the rear of the machine and it still doesn't want to come apart and i dont want to force it. any help is appreciated.

If the cord goes in at the top, take the handle off, then remove the tool holder, then you can get to the cord. If it goes in at the bottom, You have to take off the motor cover to get to the connecting end. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless

Get over it and buy a new one!!! ... Vacuums

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther

Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

How to dismantle twin clean powerhead to repair broken wires? the wires to the pc board have broken but can't seem to be able to remove plastic cover over wires without breaking cover.

... Electrolux Twin Clean Bagless Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0733 seconds