Having problems with your Vacuums ?

My belt broke. I have a replacement. I dont know how to install the replacement belt.

Answers :

There's a plastic cover over the agitator. (the part that should spin, with tough bristles)
Unscrew it. Pull out the agitator. Put the new belt over the 'spinner' (the part that's connected to the motor) and the special pafrt of the agitator. Snap the agitator back into place, making sure it's secure on both sides.
Screw back on the plastic cover.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My belt broke. I have a replacement. I dont know how to install the replacement belt.

There's a plastic cover over the agitator. (the part that should spin, with tough bristles)Unscrew it. Pull out the agitator. Put the new belt over the 'spinner' (the part that's connected to the motor) and the special pafrt of the agitator. Sn ... Vacuums

Moter belt my moter belt broke and i dont know how to replace it

You can find the manual for your vacuum by clicking on this link: http://www.bissell.com/images/UserGuides/1697_207.pdf ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Belt broke I have a bissell powersteamer and a belt broke and came out the bottom of it. I dont know how to put one back on it

There should be an access panel on the top side of the cleaner. Pry this open with a screw driver and this should get you access to the area where the belt can be changed. ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

My hoover belt keeps burning when i replace it. i dont have the manual so i dont know what im doing wrong.

Probably when you close it back together, there is a piece rubbing against that you do not see right away but could maybe hear it. ... Hoover Vacuums

Belt broke I need to find out how to get in the vacuum to replace the belt but cannot figure it out. I do not have the owners manual for this Eurka The Boss Superlit bagless (402a) please e-mail me any directions if you know how to do it,thanks. [email protected]

How do i change the belt on my eureka the boss lite vacum ... Eureka Boss SuperLite Bagless Upright Vacuum, 405AVacuum

Belt I have a bissell pro heat model number7901-1 and i dont know how to put the belt back on. The old one broke and i cant find my book.

First take off the cover on the left side of the top cover, then turn it over, remove the screw holding the red lock and pull the cap and brush roll out, remove the cap, remove the cogged belt, then you can put the new pump belt thru that slot, put o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Need to replace 2 belts on the Panasonic MC-UG302 upright hoover and I dont know how to do it. Is it possible to get a brief discription/diagram of fitting belts from somewhere. Tks

... Panasonic Vacuums

The little toothed belt on my bissell shampooer broke got a replacement but don't know how to put it back on Stark's where I bought the belt wouldn't help me man said he isn't a mechanic. well neither am I so could you send me a diagram I could follow? Thanks

Hi!  Your question has come up under Bissell ProHeat, although you don't actually specify that model. Assuming it is, the belt change operation is quite simple but hard to describe in words (it will sound much more complicated than it actually i ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Don't know how to replace broken belt on eureka pet pal upright bag less put one on broke immediately

... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

Sunbeam water dispenser YLR2524H2 - the hot water lever broke and I need to know if I can get a replacement part and can I install the new one myself?

... Vacuums

The belt 05361-01-02 broke and i want to know how to replace it myself. the repair man is askingn $115 for labor/parts.

... Dyson 05361-01-02 Belt

My Hoover Dust Manager roller brush is not turning It may be the belt but I dont know how to get to it to replace i Can you help Michelle

... Hoover Vacuums

D.d vaccum i have a dirt devil dynamite...i bought a new for it i put it on and not even 1 minute of using it the belt broke again!!!!i dont know whats going on do i have 2 put it on a certain way does it need grease or what!

Did you check the brush roll, if the ends aren't turning freely, then it needs to be replaced also. ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum


We have a video, online and printed manuals HERE. ... Kirby Generation 3 Bagged Upright Vacuum

The belt in our power nozzle is snapped in half. And were going to buy a replacement, but we don't know how to install it. How do you?

The best thing to do is take the machine to an authorized Rainbow dealer and let them replace it.\015\012If your rainbow is still under warranty, replacing th belt yourself will void any warranty there may be. ... Rainbow E series Canister Wet/Dry Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t

The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

I have a Hoover Windtunnel U5472-940. The belt broke so I replaced it. Immediately the next one broke. The belt goes around the brush cylinder and a metal post. I think there is supposed to be something on the metal post to protect the belt but I can't tell from the owner's manual. I also can't find out if this is a part that can be replaced. I've only had the vacuum about a year and a half. Thanks

You may have something in your brush bearing that does not allow the brush to turn easily thus stretching the belt. Chris ... Hoover U6455-900 WindTunnel Vacuum

Belt slipping Belt slips off and rubs causing burning smell from the belt over heating. Of course this puts an indent into the belt and has to be replaced. How do I keep the belt from slipping off? I see no place for a belt adjustment. Which I know would eliminate the problem. Really aggravating to have to replace belt only after two uses.

On the roller/brush where the belt sits if that is scarred up or grooved out that will cause the belt to slip if you can fix roller try but i suggest new roller ... Hoover Company Wind Tunnel U53019 Upright Vacuum

I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.

... Vacuums

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.

The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums

The belt broke on my proheat, I got the replacement belt and got it put on, turned on the machine and it instatly broke the new belt. Any ideas why??

Sound like brush roll is jammed solid .Clean. ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a bissell proheat carpet cleaner purchased in 4-18-2005 for $169.99 from kohls I have used it 6 times and the last time the brushes would not move cause the belt was broken and the end of the pump pulley which is plastic broke off so I reorder the pump unit and 2 new belts and now I see you have sent me a exact pump but the end that broke off that the belt rides on is made of steel or aluminum much strong piece of equipment I want to know if there was a recall for the machine due to mecha

I've owned my Bissell for over 5 years now & LOVE it! Even after vacuuming It pulls up tons of dog hair I never realized was there! I am having a similar problem, but I caused it myself & think maybe you may have the same problem, cross you ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I replaced my Bissell vacuum cleaner belt with a Bissell belt. I ordered it from them so I know it's the right one. I replaced it and the roller won't spin and the belt smells like it burning.

Beckiande485: You will need to unplug the vacuum from the wall, lay it down so you can see the bottom of the vacuum head and remove the bottom plate (foot plate) Probably philllips head screws. pull up on the roller (called the beater bar). ... Bissell Vacuums

Hi, The belt of our Dirt devil bagless vaccum broke and we got new belt and replaced it. Even after replacing the belt, the brush is not rotating. Any suggestions please ?

Did you check to see that the beater brush, the brush that the belt drives, is free of debris and moves freely?\015\012When they bind up they can cause the belt to break.\015\012Remove the beater brush just as you do when changing the belt and clean ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

Replace belt on eureka big boss sweeper. Bought sweeper got it cheap and it needs a belt. So i don't have anything to go on to replace it. Seems like there is a pulley below and not sure how to install

... Eureka 5849A Boss Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0625 seconds