Having problems with your Vacuums ?

How do i charge my i stubble 7890u it came with 2 pin plug i changed it to a 3 pin plug but it keeps blowing the socket


Answers :

It sounds like you have a stray wire shorting in the 'new' 3-wire plug..
Or some other form of mis-wiring--
Look at the plug, and make sure that your 2 wires are connected only to the 2 spade shaped plug blades--- NOT to the Ground plug.

May I ask-- why you converted to the 3 wire plug?
The 2 wire plug worked in the 2-wire plus ground receptacles, OK, didn't it?

Mack B
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do i charge my i stubble 7890u it came with 2 pin plug i changed it to a 3 pin plug but it keeps blowing the socket


It sounds like you have a stray wire shorting in the 'new' 3-wire plug.. Or some other form of mis-wiring--Look at the plug, and make sure that your 2 wires are connected only to the 2 spade shaped plug blades--- NOT to the Ground plug. ... Vacuums

I have a philips shave which I took away on holiday to the Germany.The probelm was that the two pin mains plug did not fit the Germany two pin sockets. The mains plug was about two millimeter to narrow to the pins in the socket. Therefore I could not charge my shaver Mr Jackman


Germany has 220 volt outlets ... Philips Vacuums

Plugged my Dyson in this morning, switched it on and power came on for not even a second and died. No power what so ever to dyson - checked my house sockets, changed fuse. Still not working - dead as a door mouse. What could it be? Many thanks Sam


It is either your power cable, cable rewind mechanism or your motor. \012\012Try switching it on, and wiggling the lead near the plug and see if it fires up. If it does, remove the moulded plug and fit a standard plug. \012\012If not, lik ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

My vax essentials hoover, model number vec-01 keeps blowing fuse as soon as it is plugged in and turned on. Cleaned the filters and have changed the fuse 5 times


... Vacuums

Numatic henry keeps cutting out & plug crackles in the socket!


It wasn't the hoover, it was the plug socket! ... Numatic Henry Bagged Canister Vacuum

I've never had to change a CFL bulb like the GE 35972 in my kitchen ceiling fixture. It looks like a squared off pretzel with the socket in the middle and facing up to the ceiling. It's been in there for years -- this is a rental -- and because it's so close to the ceiling, I can't tell where to pull the pins from the socket apart without breaking it. Any instructions or suggestions? Also, my Home Depot doesn't sell it; will the pins match a different CFL, like maybe a circular one?


CFL bulbs are held in place by a friction fit, but it is a very tight fit. Grasp the CFL by the sqaure plastic base and pull firmly away from the socket. You may have to wiggle it a little, but don't try to pull it out by the globe because they are ... GE Vacuums

I was vacuuming and noticed that the bag needed changing. the red light with the ! inside the triangle also came on. When the bag was changed, the vacuum would not restart. The red light came on. Tried the reset button but nothing happened. Tried unplugging and re-plugging in and nothing happened. Replaced all the filters and still it wouldh't start. So I brought it downstairs and tried one more time to get it to start. it worked! Is there something wrong with the vacuum cleaner? Was it overheat


It was overheated that is why it worked downstairs after cooling off. ... Miele S548 Bagged Canister Vacuum

Plug fuse keeps blowing


... Vacuums

The retractable handle doesn't stay in place. a small spring came out near the button that you push to slide the handle up and down to change the length. i need to know where the little spring goes. there is a small pin that the spring fits around but i can't seem to get it to go back in place once the spring is on the pin.


... Panasonic Kenmore Canister Vacuum Vacuum

Wertheim 4412 Hepa filter cover keeps blowing off, even though filter changed.


... Vacuums

My Braun tootbrush has never charges-i have a 240 & 11v shaver socket but nothing seems to happen when i plug it in?


When charging a device on some type of charging block you need to plug it into a regular 110 socket as the block has the correct modifications in it for the device that it charges. This 11volt shaver socket is for older shavers that dont charge up yo ... Vacuums

My cordless shark vacuum will not keep a charge even when I leave it plugged in all day it isnt very old


... Vacuums

Stopped working hello im in france, so my henry has a two pin plug. i feel all that needs changing is a fuse, but i carnt find it. i have taken out every possible screw searching for it but to no luck. iv checked and cleaned wireing and checked cable for nicks. im now begining to think maybe the motor has gone?


Hi!  Sorry you've had to wait so long for a reply, but I've only just stumbled upon your problem.  You probably don't need help any longer, but here goes anyway!\015\012You will not find a fuse, because there isn't one.  If your Henry ... Numatic Henry Bagged Canister Vacuum

My nilfisk action plus keeps stopping. it used to re-start if I drew in the lead and/or left it for a while but now it won't start at all. i have changed the fuse on the plug (not the thermal fuse), but that has not worked. can you advise?


... Vacuums

My hoover keeps cutting off and on, now it doesn't even come on. I have checked the fuse its ok and i can't cheak the wireing,the plug is moulded into the socket.


Chances are your cord was damaged inside the insulation and over time it finally opened. That would cause the cac to not operate any more. If you have access to or one of your friends has a multimeter then you can check the wiring by using that meter ... Hoover Vacuums

My steam blaster S3350 will not heat up when I fill in with the correct amount of water. Tried it plugged into other electric sockets & still have no steam.. The red light always came on when heating, now as soon as the power is on the yellow light comes on, & no results


... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I want to recharge my Philips PET741 D/05 portable DVD Player. But when I push the plug into the charging point on the side of the player,at one point, as the plug goes in, there is a quick flash of red - but no more. The red charging light does not light up, and the player does not charge. The plug cannot be held at the point where the sudden momentary flash takes place


1.With the AC power unit plugged in to the wall plug into your dvd player and wiggle it a little bit and see if the light goes on or off. If so the the power port is bad. \015\0122.Try a different wall outlet to see if it helps.\015\0123.Ensure there ... Philips Vacuums

I have a Roomba 560 (it's still in warranty !!) and, after my summer vacation, it has a problem. When I'm charging Roomba, the orange light blinks (and this is normal!) but this orange blinking continues forever.... the light doesn't change to green. If I detach Roomba from the charger, the light become green and it works normally until the light changes to red and I have to charge it again. WHY, DURING THE CHARGING PHASE, THE LIGHT DOESN'T CHANGE FROM ORANGE-BLINKING TO GREEN? HAVE I


The problem is not with the charger itself but it is with the battery inside the Roomba. It sunds like one or more of the cells has gone bad so its not holding the same charge as it did. I would recomend sending it in while the warranty is still vali ... Roomba Robotic Floor Bagless Vacuum

House fuse box blows when you plug machine in.


There is a short in your vacuum that is cause your circuit to trip. It is more then likely a ground wire that has come loose in the plug that attaches to the motor of the vacuum ... Vacuums

The charge light no longer turns red when plugged in and in spite of being plugged in does not seem to accept a charge any longer. I miss the vac use of my flipease!


Providing the charger is working must be the battery or input socket. Get charger checked out 1st... ... Bissell 52889 Flip-Ease All-in-One Vacuum and Mop Vacuum

Brum M0414 does not charge. "Charging light" doesn't go on when charging unit is plugged in. Voltmeter check on charging unit (unloaded) shows 19.5V. How do I dissassemble Brum to check battery and battery connections?


... Dirt Devil BRUM M0414 Bagless Vacuum

Chain tensioner Is it possible to change the chain tensioner of the Husqvarna 240 to a tool less chain tensioner or at least to the chain tensioner where the adjustment screw is accessed from the side not from the front. The problem is that there is a little plastic part that breaks rendering the chain tensioner useless. I have changed it twice and it keeps breaking. To change it you have to change the whole part that covers the break and chain mechanism.


... Husqvarna DMS 240 Core Rig - DMS 240 w/ Vacuum Pump

Hello, I have a Kenmore Progressive Canister Vacuum 116.20912006. It won't turn on. On the hose assembly, the end where the hose swivel is, there are 4 metal pins that plug into the canister. One of the pins looks like it broke off. There are only three pins remaining. I assume there should be four pins as there are four holes. Is this the problem and is it fixable? The vacuum is from 2002 so I am not sure a replacement part is even available and at what price. Thank you. Susan susan.eng@


Hi Susan, if the pin has broken off you can do one of two things, first, would be to find a local vacuum repair shop and take it there for them to look at. they may be able to look at the hose and fix it for you pretty cheaply. what ... Kenmore Progressive 20912 Bagged Canister Vacuum

My shop vac blows and doesn't ****! I put the hose on either hole and it blows dirt all in my house. I'm trying to vacuum. I can't find a switch to change it from blowing to sucking and if I put the hose in either hole it just blows.


... Eureka 2812 Wet/Dry Vacuum

Dyson DC23 Vacuum shut off and came on. Thought it was a problem at the electrical outlet as when moving plug it would come on again. Seen canister was full, emptied it and cyclone was quite plugged up so poked out the dirt. Had dog hairs in it as well as some ashes I had just vacuumed. Plugged unit in again and pressed switch. Will not come on. Tried another outlet. Is there a reset button somewhere or could the ashes have seized the motor. What can I try besides taking it to a repair sho


... Dyson DC23 Bagless Canister Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0704 seconds