Having problems with your Vacuums ?

Bissell PRO Heat Steam Cleaner is not dispensing the water. I took it apart and cannot find any obvious issue with it i.e loose tubes, connectors etc.

Answers :

Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be on the tank, not in the hole. The flow indictor cap is leaking air or maybe is too tight. If you had the top cover off, make sure that the tubes are routed right so as not to get pinched when the cover is put back on, the smart mix knob should be in the water setting and that the piston is on the bottom of the smart mix knob. Pump is bad. Try running a mix of vinegar and water to see if that unclogs the lines.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissell PRO Heat Steam Cleaner is not dispensing the water. I took it apart and cannot find any obvious issue with it i.e loose tubes, connectors etc.

Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Vacuums

No power. I was getting intermittent power with my miele s558 midsize canister, but it was predicated with me fiddling with the retractable cord to get it to come on and then not move the canister while I was vacuuming. Now I can get no power. I have taken it apart and can see no issues with connectors, cord, casings, etc. It all looks fine. It is about 5 years old and I have had no problems with it.

... Miele S558 Red Velvet Bagged Canister Vacuum

My magic blue vacuum has no suction. The lid seems loose and the lack of suction seems to be related to the loose lid. I cannot find a way to tighten the lid.

Have u tightened the dirt cup lid. ... Vacuums

Dyson DC04 i have a loose wire where the cable enters the cleaner how do i open the part where the on/off button is. A wire is loose probably but I cannot get to the interior to check its status. How can I take it apart? the plug is sealed but could it be a loose wire in there?

You have to remove the yellow switch but to do this there is a small hole at the side of the switch nearest to the machine you have to push something in this which will push the clip that is holding the switch if you can do this there is a screw behi ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I

You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

I am trying to take my philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag was not put in correctly. I have removed all visible screws but cannot for the life of me find how the wheel end comes apart. any tips?

Generic problem for all Vacuums\015\012I am trying to take\015\012I am trying to take my Philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag ... Vacuums

I need to find a way to replace the attachment hose on this unit. the tube to spray the detergent snakes into the base next to the wheel and i'm unsure of how to take it apart without breaking it. is there a simple way to remove the wheel? do i need to do something special to replace that tube?

The best thing for that situation is to look on the side of the road and you will find a Bissel, I see one or two a week. Take one home and experiment on that one not yours. I have brought many and never have I bought one. I never see a Hoover by ... Bissell 9200 Upright Vacuum

Power Issue Hi...my Miele vacuum cleaner (S314) will not turn on, unless I lean it on its side (the side that the power switch is on). I took it apart and the wires are all well attached, and I do not see any issues with the connectors. Is this a common problem with an easy fix? Thanks! Todd

Could be the cord reel causing the problem. Sometimes the contacks on the inside of the reel loose contact and won't conduct. If this is the problem, then you will have to replace the reel cord asm. Part # 06777540, may cost about $150 approx. ... Vacuums

I need to replace the cord on the beater brush attachement for s3614 hoover powermax.. can't find parts. I was able to pull apart the brusher, but I cannot release the wire to resplice and reconne

... Hoover S3614 Vacuum

540 Roomba goes in tight circles left and right after backing off charging base - stops and give oh-oh signal and 9 beeps - I have taken off bumper and cleaned sensors etc - blown out with air and still have same issue - unit will also not find or go back onto charging base - any suggestions /

... iRobot Roomba 540 Vacuum

Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho

Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums

Have a windchaser portable ice maker which only makes one cube at a time. I have been told one possibility is a clogged freon tube, but no suggestions on repair. Another is low freon, but I cannot find a fill valve. Any suggestions?

CAUTION !!! ----freon re-charge should be performed by a trained service person -- this can be very dangerous if trying to perform yourself.\015\012depending on the year of the unit --one thing that I would check is to make sure you have good a ... Vacuums

I have a miele s184 and on the same side where the hose connects to the bottom of the vacuum, the housing is very loose. It does not come apart , but it looks like it could. I cannot locate a screw or anything to tighten. Can you help.

... Miele S184 Powerhouse Bagged Upright Vacuum

My Kenmore bagless intelliclean vacuum is making a loud noise mainly when it is vacuuming on the highest setting (when the light is red). We have taken it apart and cannot find a clog. It has also lost suction.

This might help, it was posted on a previous problem but is the same issue you are having it seems: "Here is a possible solution. If the v ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

My sister dropped her roomba than brought it to me complaining it does'nt work anymore. I took it apart, cleaned everything i knew to clean,could not find anything obviously wrong so I put it back together.I charged the battery than tried it. The green light comes on when you push the clean button and it makes a little grunt noise but that's it.

Have a look at the motor brushes if there broken or poped out this is were the "grunt is coming from" the motor is trying to turn but cant? ... iRobot Roomba 4000 Bagless Robotic Vacuum

My roomba 550 makes loud clicking noises and stops after 5 minutes and tells me to check brushes. I have taken it apart as much as possible and cannot find the problem

Pull brush rollers out.pull funny lookin yellow ends off and clean hair ect.out .also pop out front wheel and clean ... iRobot Roomba 550 Vacuum

Bissel vacuum My bissel powerforce somehow is loosing its suction Ive no clue why Ive checked for clogs etc. but Icant find the problem please help!!

Take the dirt cup out and turn the bottom of it that will let you get to the filter,there should be some finger twist plates on the top,turn and take it out,there will be a foam cover around the filter,take that off and clean with warm warter,when do ... Bissell 3522 PowerForce Bagged Upright Vacuum

We have the bissell pro turbo with heater and we cannot get any suction for the water. took completely apart and couldnt find anything.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My dyson dc18 loosing suction , took apart and didnt find any obstructions

Hi its Darran at Dyson.A loss of performance is normally attributed to a blockage or a dirty filter. Please ensure you follow the full blockage procedure outlined in your user guide or in the Support sectino on our website at www.dyson.co ... Sharper Image Dyson Slim DC18 All Floors Vacuum

My shampooer is not putting out soap in a steady stream.It is like it is clodded up. I have taken all the parts apart that I can and cannot find any clods.

The plastic screen which suppose to be attached to the shampooer tank (under the dial) is probably stuck in the hos remove it from the hose and attach it to the tank. See if you put correct proportions of shampoo and make sure that water is warm. ... Kirby Ultimate G Bagged Upright Vacuum

The beater bar makes a loud noise and something is cutting into on the end opposite of the belt. I have taken it apart and cannot find anything that appears to be out of place. Lynnette

Check to see if the belt is missing any gears. If it is then that is your problem. anothe issue might be that the roller bearing is loose or missing. you will be able to see this when you take off the bottom plate. let me know if this helps. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a dirt devil featherlite bagless vacuum; model #088600. It has suction through the hose but not through the floor mode. I think there is a blockage in the hose area but cannot seem to take it apart enough to find it.

There are 3 screws 2 on the left side behind the hose and 1 on the right back by the wheel.that will take the cover off.if you need to get into the bottom there is a screw on the bottom plate in the area where it looks like the belt travels.is the br ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

My Kenmore Progressive is making a noise that sounds as if something is blocking the suction. I have checked the tubes and can't find any obvious blockages

Have you changed out the bag? Checked the air filters? When you run it and hold your hand over the hose opening, do you feel suction? \015\012Check the head for blockages, you said the tubes are good, so check the hose, if no obstructions there ... Kenmore 25512/ 25513 Progressive Canister Vacuum

The solution tank in the back of the Bissell spotlifter has been taken apart. Cannot figure out how /where the spring etc go to make it fit. a diagram would be helpful

... Bissell Vacuums

Have DC07 that won't come on. Wife said this started happening a few weeks ago. Would come on and then other times would not come on. Now will not come on at all. Believe I have a lose wire. Have taken off star screw by on off switch, but cannot find how to get plastic parts apart to get into electrical connections. How do I do this? I am sure I am missing something simple?

... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0533 seconds