Having problems with your Vacuums ?

I had a house built last Sep. Oct., They installed a Hoover Windtunnel System. I can't figure out how to use in in the garage, were it is installed. There are no instructions and no power at the place that looks like were you would plug the hose in. The system came from Costco. Joy Long [email protected]

Answers :

What model do you have?
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I had a house built last Sep. Oct., They installed a Hoover Windtunnel System. I can't figure out how to use in in the garage, were it is installed. There are no instructions and no power at the place that looks like were you would plug the hose in. The system came from Costco. Joy Long [email protected]

What model do you have? ... Vacuums

Where can i buy parts for the model C151D vacuum. any place i checked does not have that model of electrolux listed. i need the power wand attachment. i ordered one that looked like it from sears parts direct but it wasn't the proper one and they do not list the model C151D

Any Aerus Electrolux store. For the one nearest you, check the below link and follow the directions. Keep in mind that if it's too far away, they do ship. If you're close enough, they do deliver.\015\012This model is not the same company tha ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I'm looking for instructions for. The Kenmore Seal-n-Save Deluxe. It is model 69019. The machine is in excellent (looks never used condition and I have boxes of the bags.) I just can't find the instruction book and my attempts to use it don't work. So my question is simply where can I find the instructions or instruction book. I have food I'd like to freeze. Thanks in advance.

... Kenmore Vacuums

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?

Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

I have a Series G Kirby Model G7D. The other day when I was vacuuming all of a sudden the TechDrive (Power Drive Assist N/D) pedal fell off. I see the hole that it goes into but when I put it in it's loose and falls out and doesn't control the power drive anymore. When I shook the vacuum I heard something rattling around inside the vacuum head. So I unscrewed the bottom and looked inside and found a small metal part labeled K3 on one side and T on the other side. It looks like it would fit

Hi, I have a Kirby G4 and i'v replaced the carbon brushes myself using a step by step guide however since its been back together it worked for about five minutes it then started sparking from the inside!!(a lot!!) I'v obviously touched something i sh ... Kirby Ultimate G Bagged Upright Vacuum

Recently my central vac system started making a louder than usual and laboured sound when in uise, enough so that I took note and inspected the canister and motor while running. The motor was trowing off blue sparks and looked like it could 'POP' at any moment. I will not risk using it until I know what the problem is and how to repair it. My assumption is the motor needs to be replaced. The system came with the resale house I bought 3 yrs ago but I do not know the age of the system itself.

... Vacuums

I've never had to change a CFL bulb like the GE 35972 in my kitchen ceiling fixture. It looks like a squared off pretzel with the socket in the middle and facing up to the ceiling. It's been in there for years -- this is a rental -- and because it's so close to the ceiling, I can't tell where to pull the pins from the socket apart without breaking it. Any instructions or suggestions? Also, my Home Depot doesn't sell it; will the pins match a different CFL, like maybe a circular one?

CFL bulbs are held in place by a friction fit, but it is a very tight fit. Grasp the CFL by the sqaure plastic base and pull firmly away from the socket. You may have to wiggle it a little, but don't try to pull it out by the globe because they are ... GE Vacuums

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Belt type Ok, thank you for the help! I did have the top off, but did not know the taking the motor loose trick, thank you for that! Now I have a couple of more questions, and thank you so much for all of the help! I got a belt from sears, & the sales guy sold me an off brand belt. It looks just like the belt that broke, although do you have to force the motor back down into place? I think it may be the wrong belt? I have looked on the Hoover website & they do not even have parts listed fo

The belt number is 91001028. The belt will be snug but not real tight, so the belt you got may not be the right one. Most repair shops for vacuums should have this belt in stock. ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

I recently lost power to the power head. Thinking the hose was not sending current to the head, I bought a new hose. It did not solve my problem. I have since noticed that a warning symbel is appearing that indicates what looks like a key with TA inside. The vacumn has good suction. Please advise John.

Hi\015\012\015\012Please check the link bellow to diagnose your problem…..\015\012\015\012http://home.howstuffw ... Electrolux Epic 6500 Vacuum

Last time I used by Hoover it worked fine, took brushes out to clean them and now when I try to put them back in they won't snap into place and lock. Looks like all tabs on both sides of the brush piece are there and I spin the brushes for the center spindle to line up but it won't snap into place.

Just slightly turn the brush wheel, The tabs look square, but are just a little different in one direction ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Our housekeeper has twice pulled the cord out past the yellow marker and we've had it repaired both times at a cost of $75 ea. The housekeeper is now gone but I would like to try and fix the problem myself but cannot find disasembly instructions. Looking for some assistance as I really don't feel like spending another $75 if I can take care of it. Thoughts ?

Try this. Set vacuum on it's back end. Gently pull out cord and release. It may take a few tries, but should work\015\012Repair/service manuals are only available to authorized service tech at authorized Aerus Electrolux stores. These are i ... Electrolux Lux 5500 Canister Vacuum

I have a bissell power steamer model 1694 and the roller on the bottom is not folding down to scrub the carpet like it looks like its suppose to do? I bought it used and have no paperwork. I flipped it over and one side comes down but other is stuck

Sorry this is all i can find it may give you an idea what to look forhttp://www.vacsite.com/en/bissell-parts-1/bissell-parts/1694-upri ... Vacuums

I have a nutone 350 central vac system and will will not start. Plug in the hose and I can hear a buzz at the unit like it is getting power but is not turning on. Does not matter what outlet I try

Your problem is incide the vaccum some object is stock , and the blower is cut. ... Broan-NuTone CV350 Performance Bagged Central System Vacuum

When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.

Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Looking for someone to instruct me on how to take apart my hoover steam vac so that I can check for clogging. It just stopped extracting water from the rug everything else sounds fine. The return holder is in place and has been checked many times. Any help?

First remove the dirty water tank then turn the unit on if your facing the front there is a duct on the right where the tank sets there should be a black seal around it if you have suction there then you will need to check the tank ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

There is a shaft that comes out of the pump of my Bissell 1623-1 Power Steamer with gears on it. The belt to the brush attaches to it. When I went to change the belt, the belt was fine but the gear itself with the small shaft on it was no longer attached and just dropped out. It looks like there might have been a bushing there, but no more. Any ideas?

... Bissell Vacuums

I am looking for a site that will show me the parts for my flotec emergency water powered backup sump pump system # FP480WBU skew # 2231533528

Http://www.flotecpump.com/asp/ProductLiterature.asp?brID=2&mID=FP480WBU&pID=821 ... Vacuums

It's been awhile since I have used my shampoo system on my Ultimate G series Kirby. Well, as instructed I took it apart and cleaned it. Now I can?t figure out where to put the ?screen cap? and ?sponge filter?. I have my manual in front of me and the only place it shows the filter and sponge (page 35 in the manual) is when it?s been taken apart to clean. It doesn?t show where to put it back. I don?t know what I would do without all the pictures in the Kirby manual. HELP! Thanx. Visual Kirby Vacuu

Hello,\015\012The littlew round screen goes in the hole where the hose attaches to the tank. The round foam filter goes up in the hole underneath the on/off valve for the foam. Here is a guide if you need any more help...\015\012\01 ... Kirby G6 Bagged Upright Vacuum

Help hi i have a eureka bravo model #9270 and i need instructions how to change the belt, i took out twoscrews it looks like the top comes off but it doesn't come off all the way.

The handle should be down and the top may have a tab on both sides to pry out with screwdriver. lay handle down and turn machine over. look closely around base between cover and there should be a tab to push on and cover comes off. ... Eureka Vacuums

Lux legacy canister vacuum - the top light on the canister went on. No power to the bottom of the roller. What does that light mean. Looks like a plug

The "plug" light simply tells you the machine is plugged in and receiving power.\015\012I'm not sure what you mean by "no power to the bottom of the roller". If the power nozzle motor isn't working, make sure nothing is wrapped around the brus ... Electrolux Guardian Bagged Canister Vacuum

Loses power & smells like burning. I'm worried the motor is burnt up. the belt looks fine.

If the belts are intact and the brush roller is rotating and the problem persists, the machine should be inspected internally at an authorized Service Center. Go to www.bissell.com ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Powerhead woes Drive belt for power head beater brush on Hoover S3755 keeps jumping off drive motor shaft when vacuuming low pile carpets like oriental rugs unless minimal suction is used. Any tricks to keeping the belt in place other than this?

I've had my Hoover S3755 for about 2 years and loved it, at least until the last couple of months when the "belt slipping off" problem started. I changed the belt and the vacuum would work for a little while then the belt would come off again. I pu ... Hoover S3755 WindTunnel Bagless Canister Vacuum

Windtunnel Hello: I was reading thru another readers problem of power to vacuum but won't turn on. Same problem for me. All hoses are free of clogs and I have the vacuum basically taken apart as far as I can. You state a THERMO by the motor may be open. What does this part look like? Thank you. Craig

The thermo is a small square piece with two wires coming out of it. Did you check the switch? The switch has a high failure rate. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Do you know what a filter bag looks like in a central air vac system?

The unit displayed is a Beam Electrolux central vacuum power unit. It has a 15litre dust bucket which does not need any dust bags.\015\012\015\012If you take the bucket off you will notice a white shiny weighted bag hanging down. This is ... Beam Industries 2775 Serenity Plus Central System Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0910 seconds