Having problems with your Vacuums ?

Will sew for 2-3 inches and then slows and stops. Hand wheel very stiff. End having to remove fabric and start over turning hand wheel until it loosens and then will sew for few inches and repeat the problem.


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Will sew for 2-3 inches and then slows and stops. Hand wheel very stiff. End having to remove fabric and start over turning hand wheel until it loosens and then will sew for few inches and repeat the problem.


... Vacuums

I have a 5260D Baby Lock Serger, which I had tuned up a year ago. I haven't used it very much since. When I took it in, and again now, it sews fine for awhile, then starts slowing down until it is barely sewing, even with the foot all the way down. The hand wheel seems very tight. - it doesn't turn freely, but takes a some push, like it is resisting a bit. Any idea what could cause this slow down and the tight hand wheel? I appreciate any ideas. Thank you. Maura


Hi,Since you say that you didn't use it for many years then does it make noise?If so it need oiling on its parts.oil orifice and point of contact.Please do rate the solution if the issue is resolved or post a comme ... Vacuums

My Discovery 4210 Roomba will run normally for about 20 minutes on a smooth, wooden floor. It then begins the following sequence: run forward a few inches, turn in a tight counter-clockwise circle a few revolutions, stop, power off a few seconds, power up, repeat cycle from forward run. The sequence can be repeated seemingly endlessly if I don't turn off the power manually. I've replaced the motor, and led revolution sensor system on the left drive wheel. I've blown the dust out of everywhere. A


This robot vacuum has a electronic micro processor that controls the unit and tells it how to operate and where to go based on programmed parameters. It's quite a technical marvel. I have dropped a link here for contacting the company tech support li ... iRobot Roomba 560 Robotic Vacuum

I have a white sewing machine model 999. the hand wheel is 'stuck'. i cant turn it to make the needle go up and down


Hi,\015\012 \015\012You can try followings:\015\012 \015\012- Clean the bobbin case.\015\012- Be sure that there's no thread stuck anywhere. ... Vacuums

Roomba goes in a circle moves about 5 inches and then turns in a circle again. It won't dock or go any farther than a few inches before turning in a circle again. The roomba has been cleaned inside and out. All hair and debri as been taken out of the wheels and brushes. i opened the case and cleared all the debri and i dusted the sensors in the front. Not sure what to do now.


... iRobot Roomba 550 Vacuum

My Jacuzzi Tracker 4x just "stopped"..there is a nice strong flow of water going into it, but the wheels just aren't turning. I've tried the following to no avail: 1. blocked suction for a few seconds underwater with my hand (this has worked in past) 2. try to move front wheels back and forth (but they won't budge...back wheels do move on track though) Should I start taking it apart?


... Vacuums

I have the Janome 6600 P. Beginning a seam the thread knotted and the machine made noise and needle would not move either up or down. I manually moved the needle using the handwheel and cut away the knotted thread. I began sewing again but instead of starting at the edge began about a half inch down, forward stitched, reversed to lock threads and problem repeated and received the message to "Stop for safety purposes". Did that. Referred to the manual, tried manual recommendation. Did not work. I


... Vacuums

Needle rubbing I have a singer pro finish and recently I broke a needle and the lower looper also busted clean off. I ordered the lower looper and replaced the broken one and changed both the needles. Now when I turn the hand wheel and the lower looper moves to the left and the needles descend they pass in front of the looper but when the needles begin to move up and the looper moves back to the right the needles bend back and go behind the looper. Help! Thank You!


... Singer 14CG754.CS Pro Finish Industrial Commercial-Grade Serger

Water is not being discharged. I have filled the reservoir that holds the carpet cleaner fluid And I have filled the water container. I know how to use the cleaner, it has always worked, But now, no water is being discharged to the carpet. I turn it on, squeeze the trigger, but nothing comes out. The wheel that is suppose to spin (to indicate that water is being discharged) is not spinning. Everything else works. I.e. the suction works, and the hand held accessories work.


That means that the pump belt is worn and it needs to be replaced. You can get a replacement belt and view the manual here:Bissell Pump ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Roomba 550 will not go forward, only turns and moves a few inches in reverse. I changed out the wheel motors with no results. Cleaned bumper and sensors with no results.


... iRobot Roomba 550 Vacuum

Singer 4526C appears to be jammed. Hand wheel very stiff to turn and when pressing foot control machine moves very slowly.


... Vacuums

My polaris 280 will not start. Wheels turn ok by hand. Bag is empty, side valve of pool sucks ok, where the Polaris is now screwed into. Booster pump works and is not overheating. Do I have to have the skimmer open or shut? It owrked ok last year. Was kept indoors over winter. Nothing broken.


... Polaris 280 InGround Swimming Pool Cleaner F5 Vac-Sweep

The Roomba 535 runs but stays in 1 spot moves 2 inches turns and repeats the process about 10 times. then a red indicator light starts blinking and the unit shuts down


Any beeps? If so, how many?\015\012\015\012Is there a pattern to the light blinking?\015\012\015\012Not really enough info yet to be certain, but it sound like the cliff sensors may be dirty. \015\012\015\012Here ... iRobot 530 Roomba Vacuuming Robot, White Vacuum

Roller on Dirt Devil hand vac won't turn


Usually the ends will pull off so you can clean them. If not, then you will have to replace it. ... Vacuums

I have a model 116.35922 beltless drive vacuum. The agitator brush will not turn with the vacuum running and the handle down. The brush turns by hand and the reset button has not popped. Ther is nothing wrapped around the brush, but it does feel to have some resistance when moving by hand.


Wich bags for vacuum cleaner kenmore model 116.35922 ... Kenmore Vacuums

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.


... Hoover Tempo Widepath Upright Vacuum - Blue

Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st


Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums

Oreck XL How to remove rear wheel. Removed all viewable hair, thread, etc., but one wheel is still hard to turn. I think there's hair stuck inside the wheel core. Can I remove the wheel & take it off the metal post?


You can take a medium size flathead screwdriver and slide it in beside the wheel and under the pin. Then pry carefully on one side and then the other it will start to come out but work both sides alternately so you won't put too much pressure on the ... Oreck XL2000 Bagged Upright Vacuum

My Singer Izek sewing machine starts and stops and wont sew continuously. When I push down the pedal it sews about 2 inches then stops and light starts flashing, I have to let off of the pedal and push it again, over and over. It did this once before for awhile and then just started sewing right for awhile and now its started it again. I've checked everything.


If it's not the thread and not the pedal then it's definitely a power problem. You need to replace the power cable and then check again the functionality. ... Vacuums

I have the smaller oreck portable hand vaccuum & it won't turn on. It was working fine in the one bathroom & I moved to the other & bathroom & it won't work or turn on at all?


Check the wall outlet has poser and make sure the plug is fully inserted. ... Oreck XL2200 Bagged Upright Vacuum

I own a Halo vacuum cleaner and I cannot get the wheel to turn, the belt is on securely but it still will not turn, what am I doing wrong?


... Halo Vacuums

Handwheel is difficult to turn


The difficult turning is a symptom of a bent shaft, which is jamming on it's bearing surfaces. This problem will need the atttentions of a sewing machine mechanic. Operating the machine in this condition will likely cause further damage. ... Vacuums

I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being


Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha


... Eureka Smartvac 4870 Bagged Upright Vacuum

Have a 3 year old Pfaff Creative Vision. Has less than 14 total sewing hours on it. Has had issues in the past. Breaking needles, wouldn't stitch out designs in acceptable manner(badly distorted looking) breaking needles repeated, now it is changes stitches on its own, then went to sewing the same stitch but isn't sewing it consistantly. I have taken it back to the same professional to repair each time. Can thhis machine be repaired??? Should I trade it off and get another, this isn't my first c


It sounds like this machine has some kind of fault in it for sure. It can be repaired again, but will likely need to be repaired again after that - down the road. Personally I recommend you just get rid of this unit and go for a different model. Y ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0450 seconds