Having problems with your Vacuums ?

How do I replace the on-off switch on a Hoover Wind Tunnel vacuum model U6630-9000?


Answers :

Take off the handle, then remove the tool compartment, then you can access the switch.
\015\012
\015\0123ad10a9.jpg
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I replace the on-off switch on a Hoover Wind Tunnel vacuum model U6630-9000?


Take off the handle, then remove the tool compartment, then you can access the switch.\015\012\015\012 ... Vacuums

Hoover, model # UH30070 Wind tunnel vacuum Brush won't turn. I do not see how to remove this to replace the brush, and besides it's only about a year old! Why is it already broken? There's no visible evidence on the brush that would make it stop, i.e. string, clogged, etc. Can you help?


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Is there a fuse in the hoover wind tunnel model 6425-920, the vacuum just shut off during operation and will not re start with the switch. What should I attempt? Thank you.


There actually IS a fuse/buss of sorts, if you really stretch the definition, anyways...so if your switch checked out good, and your outlet didn't fizzle out and blow a house fuse or trip a breaker, in the machine base, near the motor, there is a "Th ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Supreme wind tunnel upright model. I have a bad on-off switch. How do I replace it?


Take the two screw off the handle and then remove the upper handle devise. This will expose the real on/off switch which is on the top of the unit. There is a plastic actuator that rubs up against the switch when slide the plastic switch on the han ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Replace on/off switch on hoover vacuum


My wife picked one up on the side of the road that someone had tossed. The power switch would not turn off. I took the two bolts out of the top part of the handle, and then removed the screws along the back. This will remove the required panels to ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I own a self-propelled Hoover Wind Tunnel vacuum cleaner (Model U6425-920). I do now have an owner's manual and was wondering how to clean the Hepa filter on this model (*this model uses a vacuum cleaner bag also).


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=794479\015\012Generic problem for all Vacuums\015\012I own a self-propelled Hoover\015\012Posted by goh ... Vacuums

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel


The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Model U6637-960 Hoover Wind Tunnel with a broken on-off switch.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I forgot to replace the vacuum cleaning bag in my Hoover Wind Tunnel Supreme Mach 3.3! It overheated and turned off. I spent all afternoon cleaning the dirt out of the inside, filters, etc. It still overheats when used over 1 minute. Do I need to buy a new vacuum?


... Vacuums

Wind tunnel by Hoover, vacuum will not turn off by using switch on upright handle. do not see a way to get to switch. modle no. U5458-900


Follow the cord and look for screws inside the bag compartment at the top. a panel should lift off allowing access to switch and cord. If swtch is melted it must be replaced with special hoover switch kit which has new wire and heavier duty switch. b ... Vacuums

Replace power cord Hoover U5757-900 - Hoover Company Wind Tunnel U53019 Upright Vacuum


... Hoover Company Wind Tunnel U53019 Upright Vacuum

Hepa filter does not turn on hoover wind tunnel vacuum model U6630900. It was working (turning) and I cleaned the filter and canister and now it no longer spins when the vacuum is running.


The part you refer to is not the HEPA filter. It's a very common misconception that that part spins - it looks like it when there's dust whirling around it. In fact, it does not spin - there are no visible moving parts. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Replacing a belt Hoover wind tunnel - Hoover Vacuums


You will find four screws under the bottom cover. remove these. remove the beater bar, loop new belt on bar on pulley area. install the bar and then pull the belt over the motor shaft. re-install cover. ... Hoover Vacuums

My Hoover Wind tunnel has even a cheaper on/off switch and now, you can't buy a new one. I used to go to their website which had a wonderful diagram of the 'guts' but now the only parts are the obvious ones, belts, filters etc....I have to vacuum twice a day and I should be the test person cause its on and off on and off, but now for a vacuum I purchased 3 years ago for over 200 bucks and I can't fix it myself really makes me made or do you know where I can get this part? help? if not, I will ne


Have you tried going to appliancezone.com? I go there when I need parts... ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Hoover wind tunnel


Did you check down by the brush roll for a clog in the dirt inlet. And is the brush roll turning freely, if it is being lugged down, it can cause the motor to overheat and the thermo protector will caught it off, until the motor cools down. But if ... Vacuums

The handle comes off my Hoover Wind Tunnel PAWS vacuum model #UH702010


... Vacuums

How to replace belt in Hoover U5402-900 Wind Tunnel Vacuum


... Hoover U5402-900 WindTunnel Vacuum

Replacing hose on Hoover wind tunnel model hu70120


... Vacuums

No power to Hoover Wind Tunnel Vacuum


The problem is likely the switch a shot of wd40 should fixed it ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Hoover Wind Tunnel bagless mach 4.7 vacuum that shuts off after about 30 seconds. I suspect it is overheating, but there are no clogged lines. The on/off switch is in good working order. Help!!


Is your filter clean? you should be able to see the pleats in the filter pretty clearly. also the metal screen that is next to the filter should be clean as well. if the problem continues it could be a faulty thermal protector ( a device that shuts t ... Hoover Vacuums

On my Hoover 6660-900 bagless upright self propelled wind tunnel vacuum when I replaced the cable which works the power drive, there is a spring next to the control arm which I cannot quite figure ou


... Vacuums

I have a hoover wind tunnel model# u6476-900 and I'm having trouble replacing the belt. The extra belt that came with it was belt # 38528-035 and it's smaller then the old one and I'm having a hard time putting it on. Is this the right size belt?


Yes it is the right belt. the easiest way to get that belt on is to put it on the motor shaft first, stretch and start at the top of the self propelled pulley and rotate til the belt tracks on. you will need to keep pressure on the belt while you rot ... Hoover U6476-900 WindTunnel Vacuum

I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.


Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums

How to replace motor on a hoover wind tunnel bag type vacuum?


Hi,\015\012 \015\0121. Unplug The vacuum.\015\0122. Put the vacuum on an easily cleaned surface n ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1192 seconds