Having problems with your Vacuums ?

I need a power cord for my Cosmopolitan by Salton Warming Tray Model H132 series S


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need a power cord for my Cosmopolitan by Salton Warming Tray Model H132 series S


... Vacuums

I'm trying to locate a Salton Hotable power cord for Model H-158-S, Series M; 1000 watts; 120 volts


... Vacuums

I need a new power cord for the power nozzle on my Electrolux 2100 canister vacuum. The power nozzle has part number N115M written on the bottom. I have found the power cord for power nozzles PN6 and PN7 online, and it looks identical in photos but I'm not sure if it's the right part.


You can buy the hose at an authorized Aerus Electrolux store. If near enough, they will deliver, if too far, they can ship it. The nearest dealer can be found using the below link. Just follow the instructions.\015\012Just provide the model ... Electrolux UltraLux 2000 Bagged Canister Vacuum

How to replace power cord on Electrolux 6500 epic series


... Vacuums

Change the power cord on a Eureka series 3270-3275 vacuum cleaner


... Eureka Vacuums

My dog chewed through the power cord on my Dyson DC15. I have purchased a new power cord and need instructions on how to remove the old one and replace it with the new one.


... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I have a Hoover Wind-tunnel Vaccum (Model U5433-900) that needs a new power cord. I am looking for step by step directions for replacing the power cord


... Hoover Vacuums

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.


Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

Need to replace power cord on Hoover windtunnel need wiring help


Without seeing this it would be difficult to describe. I would take it to a vac shop and let him show you. there are no real schematics for the wiring of these units. I usually would cut off the cable with a few inches of insulation to know where to ... Hoover U5399-900 WindTunnel Lite Upright Vacuum

The power cord on a flat iron broke/got chewed through and needs to be replaced. how can I open it to get at the cord or fix the cord?


... Vacuums

The iron needs a new power cord; however, the screw at the back of the iron seems to need a hollow star driver. What tool do I need?


You've identified it in your question. These screws are just one type of so-called "security" screws (there are many others) that are designed to be turned only with a driver that matches the head. You can often get these screws to turn with a small ... Vacuums

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?


Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

Need to replace power cord on Hoover vacuum.


Remove the dirt container and look for screws. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Need to replace the power cord


Pry out the clear plastic covering the Fins going around the body\015\012Surprise no fins in there but there are some screws ... Rainbow E series Canister Wet/Dry Vacuum

While replacing my power cord on my DC25 a spring popped out I have no idea where it goes. I need a diagram so I can see where it goes


Here is how the switch assembly should go together: ... Dyson DC25 All Floors Bagless Upright Vacuum

I need to replace power supply. where the cord


Greetings from GoVacuum.com,Unfortunately there is no fuse on a Kirby Generation model. In my 10 years of repairing Kirby's as well as other vacuums I will tell you that 9 times out of 10, when a Kirby Generation doesn't turn on, it's the ... Kirby Generation 3 Bagged Upright Vacuum

Damage power cord needs to be replaced on Bissell 3920


... Bissell 3920 Bagless Upright Vacuum

Power cord has been split accidentally - needs to be adjoined to new plug


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T


... Rainbow E series Canister Wet/Dry Vacuum

I have a electrolux 7000 my cord brok off and it got succked in. igot it apart. I DONY KNOW HOW TO PUT THE COIL SPRING ON THE POWER CORD WHEEL. NEED HELP


This is very difficult to reassemble correctly, and more difficult to explain properly. You need to take the vacuum to the nearest authorized Aerus Electrolux store for reassembly. Or call for free pick up and delivery.\015\012\015\012 ... Electrolux Lux 7000 Bagged Canister Vacuum

I need to replace the power cord. what tools do i need


The Kirby vacs have a 50year warranty. You sould contact the person you baught it from and have them replace it or if they gave you one (no labor is coverd on the warranty) then you will definately need a Philips screw driver and a tub to hold all th ... Kirby Ultimate G Bagged Upright Vacuum

I dont have a power cord and or foot pedal and need to know what I need.


Power cords can be found at http://search.totalvac.com/search?keywords=power+cord ... Vacuums

I need a complete parts manual for a GE #106766 canister vacuum cleaner sold at Walmart. I need the plug receptor in the cannister for the power nozzle cord


... GE 106766 Bagged Canister Vacuum

My kenmore progressive caniser needs a new power cord. the plug had one of the metal prongs break on the plug. how can I replace the cord? model 22812201


I do not know if you want to replace the replace the power\012cord or the receptacle for the power wand?\012\012If you need the prong for the power cord you can purchase a\012replacement power plug from a local hardware store and it will functi ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.


... Sanyo Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0852 seconds