Having problems with your Vacuums ?

How do I reset the time? On a pyrex professional four event timer


Answers :

Hold down the Clear key for more than 10 seconds.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How d i reset the time on the pyrex professional four event timer..It is very old and cannot find the instructions for time reset. thanks


Just hold down the Clear button for more than 10 seconds. ... Vacuums

How do I reset the time? On a pyrex professional four event timer


Hold down the Clear key for more than 10 seconds. ... Vacuums

I replaced a Intermatic light timer with a GE 15086 timer. I have read several solution, but none fit my wire sceme. This is hooked up as a 3-way switch so the second switch can turn outside lights on manually. Here is what I have; Four timer wires: R B W G Wall outlet: B, B & R (Two), G, W bundle What ties in together to make it all work?


1) GE 15086 is not a 3-way timer.GE programmable timers are for single-pole switch replacement only. I have tested this timer, and own several GE timers, and many other brands.2) Open following link to identify timers that work for ... Vacuums

I shorted out the light socket on my Chamberlain Professional Garage Door opener. Now it wont open, I am looking for a fuse or reset button, but cant find one. Is there a way to reset it or did I fry the solinoid


First check your house fuse. ... Vacuums

I have a Sleeptight Imetec Electric Blanket with timer and Dual Controls one for each side of the bed recently the timer was set for 45 minutes and when 45 mins elasped it went off and the control light began to flash which is normal however it is since stuck in this mode light flashing will not heat just keeps flashing is there any way of sorting this the other side of the blanket for the other side of the bed seems to be ok although it did the same thing but reset itself any ideas Regards


... Vacuums

My Ken-Tech atomic clock shows the time exactly four hours earlier. It has four, not five buttons in the back. How can I reset it?


We dont have excalty the model, so its possible that this Atomic Clock with Day & Date Instrcutional Guide can helpful.Go ... Vacuums

How do i reset the timer on my rug doctor


... Rug Doctor Mighty Pro X3 Value Pack - Blue

GE on/off timer for a bathroom fan - switch has four wires Green - ground White - neutral Black - power Blue - lead My fan has two - white neutral and black lead I have tried every configuration and cannot get the fan to work. Any suggestions?


I would guess that the black wire on the timer is the power in and blue is the power out to the fan (hook it to the black wire going to the fan) The other colors are right. ... Vacuums

I have a tungsten timer TM-012 that suddenly quit working. I want to reset it but can't find my instructions. Can I get a copy of the instructions? Thanks.


... Vacuums

I can't find the directions to my pyrex professional digital probe thermometer. Can I get printed instructions online for use tomorrow.


... Vacuums

I need to reset the lock on the samsonite 375 flite comfort and cant seem to do it. It has a red button at the back of the dials with 'on' 'off'. I've pulled it forward and followed instructions to reset it but still it won't reset. I'm not sure if that button has anything to do with resetting it actually???


... Vacuums

Can't open plastic case of Shark Professional steam cleaner


Yes these are a pain....but if you use a box cutter (razor knife) you can open it right up. It's a must have around the house! ... Euro-Pro Ultra Steam SharkTM II Hard Surface Steam Cleaner Vacuum

After over heating the reset button did not reset after a cooling period.where is the reset switch /or fuse located? vacuum is a shark model UV208C


... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

I have a Eureka Boss Model 411... I need to know where the reset button is for the suction motor. The canister was clogged on the backside, I didn't see it and the suction motor shut off. I have cleared the obstruction, but don't know where the reset is for that motor. I know how to reset the brush head motor.


If your vacuum motor overheats, it will stop working. it will start working again once it cools. ... Eureka 411A Upright Vacuum

Have a hoover windtunnel platinum. I have changed the bag ( hepa Q bag) but the bag light wont reset. so the vaccum wont turn on. I have unpluged it and let it set for a while with the new bag in and repluged it in. I have checked the brushes and it is all clean but it will not reset. This only the second bag so it is a new machine I should not be having problems. Is there some sore of reset button I can hit.


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I have a hoover windtunnel platinum. I have changed the bag ( hepa Q bag) but the bag light wont reset. so the vaccum wont turn on. I have unpluged it and let it set for a while with the new bag in and repluged it in. I have checked the brushes and it is all clean but it will not reset. This only the second bag so it is a new machine I should not be having problems. Is there some sore of reset button I can hit.


... Hoover Company Wind Tunnel U53019 Upright Vacuum

GE 15086 7-day Digital Wall Switch Timer 15086 Having installed and set up timer, and put the switch from timer to off. Then, when I push the door to turn on the lamp, it does not work. Why? Thanks.


I think this is the dealy timer you have installed and if your relay is connected to the other side it becomes and switched on timer.\012So I think if the timer controller is correct you must connect the lamp to the OFF relay and when the door ... GE Vacuums

Changed the motor carbon brushes on my Beam central vacuum cleaner equiped with an IntelliWatch system. This system includes the Alutron DB100 module. This Alutron module needs to be reset so that the vacuum cleaner can operate properly. I believe that this module keeps log of running time and disables operation after a predetermined time. Can you help me with providing a reset procedure that will reset this module. Thanks


... Sunbeam Vacuums

Reset button The drive belt on my machine broke. They sent me a new one and I installed it, I think, correctly. It still won't engage and rotate the brushes. I can't find a reset button, but I suspect it needs to be reset. Where is the button? Theresa


Do the brush rolls turn ok? The brush roll motor may be bad.\015\012\015\012 ... Bissell 9400 ProHeat Upright Wet/Dry Vacuum

I have a taco japanese slot machine how can i reset it with out the reset keys i hit jackpot and i cant reset it


... Vacuums

My Miele S748 will not run the overheat light and reset light on but can not find a reset button


... Miele Vacuums

My Dyson Ball rug attachment won't work - something had caught that I cleared, but the reset button does not reset the vacuum. This happened once before and I had to take it in. Is there another way to fix this simple problem?


... Dyson Vacuums

Problems with Kenmore Whispertone model 118 Bagged Canister Vacuum Overload Protection Reset won't reset


... Kenmore Whispertone 23312 Bagged Canister Vacuum

I have an Amana above range Radarange, Model #AMV4204AAB, Serial # 10168958GE. Tonight after running for a 7 minute period and finishing, it would not again start. There is power to it, but various buttons no longer work. The following buttons won't work: Kitchen timer, Light Timer, #5 button, Popcorn, Poultry, Auto Defrost, and the Start button. Any help?


Hi,\015\012\015\012Push\015\012the power cord all the way into the outlet in case it became loose and\015\012is causing the problem. If the microwave still isn't working, check for\015\012a blown circuit fuse, and repair it ... Vacuums

Utilitech TEO6WHBL Timer. When I plug the timer into the outlet athe entire lcd readout comes on and it is hard to read. When I uplug it from the outlet it looks okay


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0190 seconds