Having problems with your Vacuums ?

Screws missing for end of filter - Vacuums

Answers :

Please check your manual for screw replacement guide
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Screws missing for end of filter - Vacuums

Please check your manual for screw replacement guide ... Vacuums

I have a sta rite (pentair) cristal high rate sand filter model T-200-BP-1....its leaking water thru the top of the valve, where the valve cover screws on the valve body assembly. it leaks water out where they go together around the screws. Also when i vacuum it, everything that i vacuum gets washed back in the pool when its on the filter position. Also the backwash leaks when its turned 2 the filter position, does it supposed to do that?...the only way i have gotten it to stop is to put a seper

... Vacuums

I have a cb9191j-10a vacuum that works fine but I am really disappointed by the small screw-on filter that quickly clogs up with dust and debris. There must be a larger type filter that could be used and this would make for a really fine vacuum. Could you suggest an alternative filter?

... Vacuums

Unable to remove round filter in bottom due to bolt not secure inside vacuum and it is just spinning so I can't remove nut holding on filter, but cannot see how to remove top of vacuum to get at other end of nut.

If you are talking about the acorn nut that secures the separator to the motor shaft, it can be removed with a small (or even a big, for that matter) air or electric impact wrench with the proper sized socket. Find a mechanic friend who has one, make ... Rainbow E series Canister Wet/Dry Vacuum

Our plug got pulled out (by driving away while the canister was still plugged-in after a vacuuming the car). How can we open up the unit to reattach the wires? We accessed two sets of screws (2pairs) toward the bag-end (not the motor-end) of the canister, but we can't locate any access for the two other apparent screws inside the body.

Remove all visible screws. Top and bottom, then once they are all removed, take a flat-head screwdriver and slowly pry around the canister until it comes completely loose and can be removed. Then you should have access to the wires which can then be ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

How to dismantle a Miele S 5980 vacuum cleaner. The RESET switch has fallen in and I can't remove the plastic panel to replace it. Neither can I remove the cleaner body to get in from beneath. I have removed 2 screws from the front of the barrel (nozzle end), one screw centre front, two screws towards rear, but there seems to be something else holding the housing together. [email protected]

... Miele Vacuums

Vacuum smells I have a 6 year old rainbow vacuum model E and it smells terrible everytime I use it. Probably because often times i don't remove the water basin after vacuuming and just let it sit. It's my own fault however now I don't know what to do to get rid of this terrible smell. I've water cleaned the hepa filter, not able to remove the separator screw to clean. Can you give me some suggestions?

In addition to vinegar, baking soda (sodium bicarbonate) is also an excellent remedy for many odour problems. Try generously sprinkling baking soda on a rug you wish to clean, and afterwards, vacuum up the spot. Rugs, and dirt ... Vacuums

I have a cannister (Animal something...) Today, it didn't sound right - like a blockage. I took out the filter - seemed OK; I looked for a blockage - found none. I continued to vacuum, but it wasn't picking up. Then, I stopped again, and I found a blockage (cat toy mouse) right at the end of the hose (attachment end.) I cleared, and I turned back on - nothing. Completely dead. It is one year old, just about exactly. Desperate, Sharon Tracy

Hello,if your canister is completely dead, then it means its having a power problem. You need to focus your attention on that part of your canister that relates to power. Such as; power wire, if you don see any fault with the power cord, ... Dyson Vacuums

I had to remove the needle, now my needle won't stay in. When I tighten the needle clamp screw, the needle slips out. Am I missing a part on the end of the needle clamp screw?

I've had this happen a few times. It's usually because I need to loosen the needle clamp screw a little more to make sure I'm getting the needle PAST the screw and far enough up in the channel so that it can be caught by the screw. I hope this works. ... Vacuums

I have a Hoover windtunnel T series. Model #UH70105. The system check indicator was almost red so I cleaned the filter. There are no clogs and it vacuums fine without the hose, but when I go to use the hose there is very little suction and all the vacuum dust flys out of the end the hose piece fits into when not in use. Can you please tell me what is wrong?

... Hoover Vacuums

I have cleaned the filters on my dust buster. The vacuum works for a minute then the battery seems to wear out and the power weakens until it stops. How do I replace the battery on this vacuum? Do I need just one 9.6V battery? What screws do I loosen to insert the battery? I can't find my instruction booklet. Tank you for your help.

... Black & Decker 15.6 Volt DustBuster Vacuum

I have a small canister type hoover vacuum and I would like to open it because the cord rewinder it jammed. I have removed all 4 screws but still can't seem to separate the two pieces. Am I missing something?

I may be able to help, but would need to know what model your machine is. Re-post, giving as much detail as possible and we'll see... ... Hoover S3330 / S3332 Straight Suction Telios Bagged Canister Vacuum

How to open 116.23512301 vacuum canister AC section to wire in replacement 4370608 cable assy. This assembly contains the receptacle that powers the hose. I found the two screws below the bag cover, but can't figure out how to release the end near the retractor lever.

... Kenmore Vacuums

Suction is not good. It is more hassle to empty. You have to take apart top filter & pull out everything stuck uptop. I end up with more dust on the outside when I change. I miss my bags. No dirt to deal with.

Yeah i agree with you...Sometimes you have to disconnect the primary vacuum hose at both ends and clear the debris in it..Then take the plastic top off the motor houseing and clean it out aswell...Its a pain rest assured :) ... Eureka 5849A Boss Bagless Upright Cyclonic Vacuum

How to disassemble the power head of Kenmore vacuum, model 11652450203C . Tried with screwdriver but is there a screw somewhere inside that I'm missing

... Vacuums

I have a Filter Queen Majestic canister vacuum cleaner. At the end of the wand, a button to release the attachement not only broke, but also one eyehole on the wand where one nipple on the button falls into. So therefore a new button isn't going to fix the wand because there isn't a hole on one side of the area where the button falls in place for a nipple to secure the button in place. IS THERE A REPLACEMENT PART FOR A NEW SECTION OF THE WAND WHERE THE RELEASE BUTTON IS SECURED IN PLACE THAT I C

... Filter Queen Majestic Canister Vacuum

Warning Light What does the light mean on the canister that has two prongs on one end and one on the other. The vacuum works fine but the light is on. I changed the bag and filter.

Check the hose and wands for a clog. Usually that light means a full bag, but a clog or restriction will also cause it to come on. ... Electrolux Epic 6500 Vacuum

Miele S5000 (revolution 5000) vacuum cleaner - How do I open the casing? When the power button on the handle is pressed the green power-level lights on the handle light, but the motor sounds like it gives a little 'jump' but nothing more. The orange power light on the body also dims. I assume the motor or fan is jammed, but I can't open the body to find out. I've taken out to screws inside near either end of the handle, but to no apparent effect. I'm assuming the body is held together by plastic

... Vacuums

How do you reattach the front end of a Kirby Heritage II vacuum cleaner so that the brush is engaged. ( Manual missing!)

You need to make sure the belt is on the roller correcty, make sure is at the red position when putting the part back on with the belt on the hook, push the pedal to highest (off the ground) position to ensure you put it on correctly, then turn the f ... Kirby Heritage II Vacuum

I am trying to take my philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag was not put in correctly. I have removed all visible screws but cannot for the life of me find how the wheel end comes apart. any tips?

Generic problem for all Vacuums\015\012I am trying to take\015\012I am trying to take my Philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag ... Vacuums

I am trying to replace the cable and actuator on a Hoover windtunnel self propelled vacuum. but I cant get the top or hood off the get to them, I have removed all the screws I can see, roller, belts..what am I missing?? thanks so much for any help

Hi there SmartAlec from NelsonVacuums.com.au here. You will need to remove the knobs for carpet/hard floor selection and the carpet height to remove the cover they act as k ... Vacuums

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems

Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

My Panasonic model MC-V6830 works but no suction. I checked and belt was loose, but there is nothing to attach the back of the belt onto. Seems some screws or plastic pully part/parts are missing. What parts do I need to order to fix this vacuum?

... Panasonic Vacuums

Kenmore progressive vacuum model: 116.25614506, I replaced the bag and filter and now it seems to **** the bag up against the hose outlet with very little suction at the hose end

... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

I have the Miele S7280...the one without the clog hatch on the back. I took the bag cover off, then continued the remove the screws and cover underneath it to detatch the top from the bottom. Found the clog and cleaned it out. Heres the problem...now the power nozzle light comes on and the vacuum "on" is lite up red, but it will not come on. Checked the filters and the bag. It certaintly seems like the top and bottom are meeting up to latch into each other, but I have no power. Help!!

... Miele S7210 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0906 seconds