Having problems with your Vacuums ?

Briggs 8.5 hp snowblower engine, stalls periodically. sometimes under a load, other times no load. sometimes within a minute or so, sometimes 15 minutes into use.

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Briggs 8.5 hp snowblower engine, stalls periodically. sometimes under a load, other times no load. sometimes within a minute or so, sometimes 15 minutes into use.

... Vacuums

The electronics in my Sunbeam TA200A Toaster is playing up. The Toaster is sometime popping the toast up after the right amount of time, but sometimes it pops up a minute later than it should (burning the toast) I have open up the control panel buttons and inspected the array of transistors and resistors that is used for the timing mechanism and a visual inspection doesn't indicate a problem. I am keen to replace the 2 transistors on the control unit (the resistors are unlikely to fail) but I ne

... Vacuums


Check all filters, if they can be washed do so, if not clean or replace. next check for a clog in the machine and in the hoses. the machine as a thermal device that if it senses an overload or getting to hot, the machine will shut itself off for safe ... Vacuums

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.

The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums

My Riccar 1700 will intermittently lose power while vacuuming. I have had the vacuum for 4 years and this is the second time that I have had this problem. The first time the authorized repairperson said the problem was a dirty hepa filter. The second time, the repairperson put on a "pig-tail"(?) and said that he did not have a shut-down problem when he tested the vacuum in the store. I just picked it up from the store today, brought it home and the same problem occurred within minutes.

... Riccar RC1100 Compact Vacuum

While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!

Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther

Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

I have had 226R 20 years. Don't use it much. I have learned to pull slack out of top thread to start so I do that. However, sometimes, as today, it will wind the thread around the bobbin holder and I have to take time to ge it all out clean it up. Is something out of adjustment or what. Sometimes it will sew OK then all of a suden it will start to wind the thread around the bobbin holder again. So I'm confused. Do you have any ideas. Thanks

Hi wwilson63,What make is that 226R?The problem is that the thread is not threaded correctly. You must be very careful and follow directions explicitly.Once you think you have it threaded correctly, sew a few stitches and see ... Vacuums

I have a vax power 6 hoover, this was bought in January this year replacing the previous 2 I had bought in 2012. I get the same problem each time in that the hoover cuts out after using it for 5 minutes and I cannot use it again for another half an hour. WHAT IS THE PROBLEM WITH IT?

... Vacuums

I just filled and started using my steam mop. There was a lot of steam initially, but the mop quickly lost steam and heat within a few minutes of using it. Any ideas?

Hi,The water you are using is not able to make steam easily...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

My sd40025 dirt devil ..it is not a upright. it is the follow along, bagless vacuum. has wonderful pick-up but the brush stopped spinning when i was vacumming my rug..i love this vacumm but it is only the third time i have used it. It is brand new. Why would the brush stop after maybe 20 minutes of total use?..please advise

... Dirt Devil SD40020 Bagged Canister Vacuum

Using my Proheat bissel 7901 I wil hear a popping sound than suction will stop. The machine can run for long periods of time or short time before it happens, what could it be?

Clog in the suction side somewhere the pop is the safety as to not burn up the motor. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My Mom has a Dirt Devil Featherlite and the belt falls off all the time. I put it on three times today and it falls off within a few minutes. The belt post I put it on doesn't have anything to hold the belt on. Is there supposed to be something holding the belt?

It sounds like the belt is too worn and loose to stay on. Buy a new belt specified for that model of vacuum and install. Ensure that there is only a slight amount of give in the belt when you press the middle. ... Dirt Devil CE6100 Featherlite Upright Vacuum

I was cleaning my carpet using my hoover steamvac ls. I had already changed the water 3 times. The last time, the water ran out and I kept running it for a couple of minutes trying to **** up some of the water off the carpet when it just shut down. I check the breaker and the outlet and they were OK. Checked my manual for troubleshooting; couldn't find an answer there. Do you think I burned the motor up (I didn't smell anything) or will I have to send it in for repair? When I clicked on your web

(1) take the tank off and reassemble to assure you sealed to the lower handle.\015\012(2) the water feed has nothing to do with the motor or electrical, purely mechanical.\015\012Hoover web site is free, no cost. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Attachment problem used a new unit w/attachment for 5 minutes...dispensed solution in a powerful triangular fashion. Then the fluid quit dispensing out of the attachment nozle amost like the pump quit working. Primed the unit several times w/ no success. checked for clogs. can't tell if the floor portion is "pumping' or just dribbling solution onto the floor with the trigger. can see no leaks at this point. unit worked for about 5 minutes on apholstery

Make sure everything is filled and secured tightly, if this a new unit it should be something simple ok, also check where machine folds down that the solution hose is not being pinched its right behind the dirty water tank ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Hoover Windtunnel cuts off after using it for a few minutes. After an hour or so, I can turn it back on again. This keeps happening every time I use it. This is my third one. I have taken the other two back to Target for the same problem and they have exchanged them.

Yes this machine has a thermal protector in it to shut off the machine if it gets to hot, this is normal. if there is no clogs in the hoses or in the machine then you will need to wash the filter at the top of the machine. you will have to remove the ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Bissell Proheat 2XTN uses full container of shampoo in 4 minutes?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Power problem I have a Generation III and lately the power button doesn't always work when it is pressed. You have to click it a couple of times and then it will turn on and sometimes it will even stop while I'm in the middle of using it. Thanks for your help

I would replace the power switch. Here are the instructions for the repair...\015\012http://rev ... Kirby Generation 3 Bagged Upright Vacuum

My Eureka Enviro Steamer won't make steam. It is only my second time to use it. It came on for about 5 minutes, then the steam stopped. The green light stayed on. I turned it off and let it cool down, added more water, then turned it on again. It didn't do anything--not even warm up.

... Eureka Enviro Steamer 310 Stick Vacuum

Miele vacuum cleaner keeps overheating and shutting off. It is only possible to use for about fifteen minutes at a time. Is this normal?

... Miele Vacuums

I have a bissell proheat 12 amp cleaner and the soap seems to just all come out at the same time. I fill the soap dispenser and within a minute it is empty and there is no soap coming out on the carpet. Any suggestions?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Sometime when I am vacuuming carpet or a large area rug, my Dyson starts making this loud, horrible, wrenching noise. It stops when I lift one of the wheels up. What is causing this? I have only used my Dyson 3-4 times.

You will need to have the clutch replaced. this is causing your problem. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My electrolux sidekick, model 1562 makes a nasty screeching sound.It happens as soon as it is powered on,the noise then gets intermittent after qa few minutes and then goes away.This cycle is repeated evry time i use it.I have checked it for binding and obstructions and oiled the motor.I think it's the roller brush but oiling it didn't seem to help

... Electrolux Vacuums

My Dyson DC07 Makes a loud sound like a belt slipping over a cog. Sometimes it will go for days without doing it. Other times it will happen every minute or so. It

Once again check for blockages in the brush bar compartment.The brush bar should spin freely\015\012The clutch may be slipping to protect its self when their is something stopping it from from turning ... Dyson DC07 Full Gear Bagless Upright Cyclonic Vacuum

My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t

... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0481 seconds