Having problems with your Vacuums ?

I have a singer 600E touch and sew. I accidently took out the bobbin case and can't seem to get it back in. Can you please tell me how? Thanks

Answers :

Open the slide plate, and remove the needle plate.The needle plate should be raised by a lever on the right hand side of the bed.Move it to the left, then raise the needle or take it out.It is also easier if you remove the sewing foot.Once you have the slide plate moved towards you you will see a black piece of metal in the front right corner of the bobbin area.Lift it up and slide it to the right.Position the bobbincase with the metal flap that locks the bobbin in towards you so when you lift it up it is on the end closest to you.Make sure the bobbin case is in the groove of the hook(the round thing that spins when you turn the handwheel)once you have the bobbin case in position you bring the black metal pieceover to the left and it will drop down to secure the bobbincase.Turn the hand wheel towards you the bobbincase should stay in place and the hook should turn around it.If it turns smoothly replace the needle plate,close the slide plate,screw the foot back on and replace the needle.You are done. www.sewvac.com
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a singer 600E touch and sew. I accidently took out the bobbin case and can't seem to get it back in. Can you please tell me how? Thanks

Open the slide plate, and remove the needle plate.The needle plate should be raised by a lever on the right hand side of the bed.Move it to the left, then raise the needle or take it out.It is also easier if you remove the sewing foot.Once ... Vacuums

I have a window fan with two fans in it & I cannot get the cover or back off so I can clean it. I* have taken all the screws out that I can get to , but there are two clamps that I can't get off, I'm not sure why the clamps are there but they are on the side with the accordian extention. Please tell me how to get it apart - after 2 years it is really filthy!! Thank you, Janet

Remove all the screws, pry clips off that hold on the extensions, than fan will pull apart. The clips must be pried off. They will not break. Then remove screws holding in the fans and remove them as well. Fairly simple process. ... Vacuums


Http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help/Upright_Deep_Cleaner_Repai ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Cord rewind The power cord is jammed and won't go in or out. I can't find a way to get the cover off to have a look at it. Any suggestions please? Power cord jammed won't go in or out. Can comeone tell me how to undo the casing to get to the power cord?

Which model do you have.. ... Vacuums

Hi i hae a star product whipper sniper and i cant get it to go i hae spark i hae fuel but it seems as if there is no fuel getting to cylinder i think it is a problem with my carby the serial no is fcb12071 please help rectify my problem cheers

One thing that you can try is to remove the carb from the unit and spray it down with carb cleaner -- maybe it is blocked (?),,, one more thing to try would be to see if it will fire using ether. there could also be something wrong with the fuel dia ... Vacuums

Cant seem to get the green light going on vacuum head,hook seems to be wrong way when its should be hooking the band off its doing the opposite

1)First, you turn the square belt lifter on the front of the power nozzle until the red arrows line up (belt off)2)Remove the power head from the front of the machine. Now turn the belt lifter the other way and line the green arrows up ag ... Kirby Ultimate G Bagged Upright Vacuum

I had to take apart hand tool for steam vac and now I cant get it back together. Please help.

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


... Vacuums

I have a dyson DC14. the forward lock came out and I cant figure out how to get it back in. Please help!

... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Elkay drinking fountain M#erpb28c continuously runs, having problems getting mounting nut back onto bubbler, seems basin should come off for access, however needind a reapir manual or access instructions to make repairs..please help

The Elkay fountains are turned on by a solenoid powered valve. There is a rubber grommet in that valve assembly that gets holes in it and then water gets behind it, causing the valve to stick on. To test that it is a solenoid problem, turn the wate ... Vacuums

I have a Swan Petmaster 1800w Hepa Filtration hoover s/r no SU3021 and cant find my instruction manuel. Problem is when on hoover it doesnt seem to be sucking anything up?? I have cleaned the cylinder and filters. Is it something to do with the bit that you can use to clear stairs/car etc and not converting back to an upright hoover again? Please help Julie

... Vacuums

How to replace wheel bracket on dirt devil. I have a dirt devil swivel glide and I took off the wheel bracket to clean out a clog and now I cant seem to get the wheel bracket back on.

... Dirt Devil SwivelGlide Bagged Upright Vacuum

I'm trying to get my S7000 Miele to stand upright an lock in this position. It wont , i tried to see if foot release was jammed but cant tell it doesnt seem to release to let it move upright an lock in again..help

There is a rear dust cover that sometimes gets stuck, this will make it almost impossible to lock the handle up. First locate the cover which is at the rear right above the wheels. It's about 2"x8" and ribbed vertically and slides up behind the rear ... Miele S7210 Bagged Upright Vacuum

Hoover F6025900 Steam Vac Widepath LS, I own this steam vac and I found bits of rubber under the machine when I turned it on, smelled like burned rubber from a belt? Can you please tell me if there is a belt on this carpet cleaner and if so, how to access the belt? I have taken out some screws and still cant get to the belt? Thanks

Well there is no belt, and not sure what the rubber would be from, everything is plastic or metal. Unless it is really an electrical smell, which means the motor is going bad.\015\012\015\012 ... Hoover Vacuums

Hi I cant get my dyson back into the upright position it will only go three quarters of the way Ive checked for blockages and cannot find anything wrong please can you help

Easy fix watch this video ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Panasonic mc-e4113 Upright vacuum. The belt that drives the brush in front is broken I have found a spare for this but there seems to be a pulley missing on the main drive shaft that the belt needs to fit on. I can't believe that there wouldn't be one? Can anyone tell me if this is the case and if so where I can get one from. Many thanks Sean

... Panasonic Vacuums

Dyson animal We bought a Dyson Animal from Sears a few years ago along with a service contract. We took it each year to be serviced. One year I took it because it lost it's suction. They sent it to the factory, but it came back still not working right. We did the same procedure over ands over many times than I can remember. I now have the cleaner in my garage and am using my old vacuum because I just can't seem to get anywhere with Sears. Please help me. We paid almost $600.00 and now it can't b

As someone who works for Sears, let me just say right now.. The service contract you bought sucks.. and does not really do anything for you. it was just a wast of money ( they have a new one now.. thats so much better because you get your money back ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I cant get the roller back in place

On the ends of the roller turn the ends and you will see some teeth ,the teeth are supposed to be aiming down.if its because of the belt,slip the belt over the roller then put the belt on the motor shaft first and pull the roller towards the front a ... Oreck XLS700A Upright Vacuum

Generation 4 Apparently, my belt came off while vacumming. I had a lot of hari entwind on the roller, so cleaned off the hair.... but now I can't seem to get the belt to stay "in place". Is it supposed to move around on the brush? or be held in place? It seems to me when I try to get the hook to grab ahold of the belt, it is going tohe wrong way to grab it. Please HELP!

First off get a new belt, I am sure this one has stretched. Then put the belt around the brush roll, put it in the center, put the bottom plate back on. Then turn the big knob on the front and turn it until it locks, you will know if it grabbed the ... Vacuums

When taking the handle/wand back to use it seems to lose the suction power regardless of what setting I use. Upon several times of standing it back up it seems to engage the suction power correctly is there a button or something that does not always engage to get power? can I fix it

When you say taking handle back I assume you mean the action to start rotation of brushes. Had simular problem and found by removing brush from tube and then cleaning "baked on rubbish" in plastic tube (so you can see clearly through tube) Clean with ... Dyson DC28 Animal Bagless Upright Vacuum

I can not get the water, normal heavy traffic selector reinstalled after taking unit apart, i replaced the pump, and now i cannot get it back together, there seems to be a special way it goes together, and i'm not finding it. Are there any videos, or pictures that show how it should go back together?

... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

How do i take the old belt off of my dyson dc 14? cant seem to figure out how to get the roller separated from the machine because i cant get the old belt off.

Go to: Dyson web site or \015\012\015\012 http://www.repairclinic.com/0100_24.asp\015\012\015\012There should be 4 to six screws holding the ... Vacuums

Can't reassemble!!! Long story as short as possible- I removed the hood from my Bissell 1699 and can't seem to get it back on correctly. The "Smart Mix" knob and it's parts seems to be the problem. How does this line-up, or what is the best way to put it all back together? Thanks, Josh

The piston is put on the bottom of the smart mix knob, turn the knob to the water only setting, then put the top housing back in place making sure that the piston went into the slot, after the top is all of the way down, turn the knob, if it turns ea ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Wont re-assemble I took the bottom plate off to clean out the rotary bush and can not get the plate back on! I think it is the position of the roller but no matter which way I place it when i turn it , it flicks back into the place that means i cant put the plate back on!

Assuming you did not remove the brush roller to clean it and consequently did not reseat it, I am guessing that the bottom plate is not reinstalling as it should. On some uprights, the bottom plate hooks in at the front and is latched in place with c ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Hi! I have a Pfaff Creative 1475. The presser foot seems "gummed up" or stuck. The back lever lifts it with great force, but then instead of staying up like the lever usually does - it then falls back down. The lifting foot stays stuck up and I have to push on it to get it back down. Help?

Bdfbjhfjffjfjfjfjfjfjfkfjfjffjfjfjjfjfjfjfjff ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1089 seconds