Having problems with your Vacuums ?

How do you fasten ( tighten to the counter) a kitchen water fauset GROHE 33759 SDE , it's loose, and the hole unit moves,when only the top part should move to the left and to the right,I tried to tighten it from under the sink ,but the nut under the sink does not have any tread,I think it tights from the top,but I am not sure how, any ideas? Thanks.

Answers :

Hi, I am Steve, lets get you some help\015\012
\015\012Your faucet tightens from underneath. http://www.grohecatalog.com/product/33759g shows full details of your tap unit.\015\012
\015\012There should be a screw thread below the sink and there will be a nut on that thread - this nut needs to be tightened to hold it in position. It is often very difficult to get a good grip on this nut and it can require a specialist tool - this link is an example of a plumbers spanner http://www.toolfastdirect.co.uk/acatalog/info_tb171g.html. They are designed to deal with the limited space when tightening faucets into place.\015\012
Is this a single handle faucet, or right and left handles?
Single should have a bolt in center mounting bracket under sink to tighten.
2 handles/levers for hot & cold should have threaded nuts under sink, above where your water lines attach that you tighten to hold it down.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you fasten ( tighten to the counter) a kitchen water fauset GROHE 33759 SDE , it's loose, and the hole unit moves,when only the top part should move to the left and to the right,I tried to tighten it from under the sink ,but the nut under the sink does not have any tread,I think it tights from the top,but I am not sure how, any ideas? Thanks.

Hi, I am Steve, lets get you some help\015\012\015\012Your faucet tightens from underneath. http://www.grohecatalog.com/product/33759g shows full details ... Vacuums

Hoover wind tunnel U6425 self propell drive pulley and nut fell off.Now when I try to put it back on and tighten it pulls the clutch assembly over so the accuator is in drive all the time and won'

... Hoover Vacuums

How do I install brushes on Hoover V2 Windtunnel? Does a right and left go on the right side and vice versa on the left side? That is how it orignally came? Or do I put both rights on the right and both lefts on the left? Thanks for your help and advice.

Both right with right left with left. ... Hoover U8122-900 WindTunnel V2 Bagged Upright Vacuum

Greetings - my Dyson DC41 animal vacuum seems to be having problems with the ball - the right side of the ball if you were to be standing behind the machine seems like it's tightening as it rolls forward, as it tightens its harder to push the machine forward. Any thoughts, any fix it ideas? Thank you.

... Vacuums

The nut on the seperator on my e series is frozen on , how do I get it off and can I use the e2 series seperator on an e series. Aparently the e series nut and seperator had to be take off more often or it freezes on...I bought a used one that's stuck and It works but I can get the seperator off to clean.

Do you have a friend who is a car or motorcycle mechanic? The acorn nut you refer to can be removed with the use of a small air impact wrench. Make sure the wrench is set to REMOVE (anti clockwise) the nut and give it a short burst. Never fails. ... Rainbow E series Canister Wet/Dry Vacuum

Unblocking sinks Can someone please tell me how to set up my kirby hoover to unblock my bathroom sink the sales man did show me a few years ago but i have lost my manual and cant remember??? Many Thanks Nina

Remove the brushead and attach the adapter (round cup-looking device with a screen or grille on the front).Attach the hose to the blower (bag) side of the machine.In your attachment caddy,there should be a round rubber attachment with rubber teeth ar ... Kirby Ultimate G Bagged Upright Vacuum

Motor doesn't run I believe it the brush on the motor. two motor brushes one is completly gone about 1/8 inch left could this be the problem.the other motor brush still has 1/2 inch left. and current to motor tested good.

Sounds like your belt slipped off. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Unable to remove round filter in bottom due to bolt not secure inside vacuum and it is just spinning so I can't remove nut holding on filter, but cannot see how to remove top of vacuum to get at other end of nut.

If you are talking about the acorn nut that secures the separator to the motor shaft, it can be removed with a small (or even a big, for that matter) air or electric impact wrench with the proper sized socket. Find a mechanic friend who has one, make ... Rainbow E series Canister Wet/Dry Vacuum

My bissell 1699 series will not spray water, the flow indicator barely moves, but when left tank on it leaked all over floor, so the water when left unattended came out. When I first hooked up the machine black stuff was on my carpet when I first sprayed.

... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I am trying to assemble the wheel axle, and cap nuts. The cap nuts will not fit on the ends of the axle?!

... Ridgid 9 Gallon Wet/Dry Shop Vac 96882 Canister Vacuum

G-5 Kirby self-propel works intermitently. The handle must be jiggled until it engages forward. The same for reverse. Once underway it will continue indefinitely until the need to change direction. Jiggle go forward,jiggle go in reverse. It seems as though it helps to push the handle at an angle to the left depressing the switch on the left side at the base of the vacuum head.

Sounds like a loose wire, the wire is connected to the handle, you may be able to fix this yourself but be careful you can void the warranty by doing it your self. (most people make the problem worse) remember your kirby has a lifetime warranty (limi ... Kirby Ultimate G Bagged Upright Vacuum

Hi there ive just purchased a bissell 1623e but cant get the 1 of the 2 screws to line up and tighten in handle any tips? ive tried holding it at all angles pushing down pulling up still it wont tighten should i take it back to shop? as faulty?

Take it back as faulty no question about it should line up easy and screw in stright away ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

There's a strip of pet hair that doesn't get picked up only on the left side of the roller, like it's rolling all of it up and kicking it out that side. I have to work from right to left to get it all up. is this a suction problem?

... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

DYson DC07 not sucking properly when in upright mode. I have tried cleaning out pipes etc and even tried an old motor section I had in garage (replaced once under warranty as kept cutting out and they left old motor section here). Even the old motor section had same prob so this suggests its something in the rest of the vacuum cleaner (whats left after you have lifted off the green motor section and dust collection area if you see what I mean? Any advice weclome please.

Blocked filters ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Roomba left wheel too slow

... Roomba Pro Elite Bagless Robotic Vacuum

Leaking from left wheel when applying trigger onmodel 7901

Sounds like a problem with the left spray nozzle, may be out of place. Either that or a line is loose and leaking. Either way you will have to pull the top housing off to check it over. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Left side of Hoover Windtunnel won't pick up dirt and hair

... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Missing Nuts and Bolts

Steve, \015\012\015\012Go to www.hoover.com and use the service center locator to find your nearest dealer, these bolts and nuts are specific to each machine. they may ha ... Hoover U5399-900 WindTunnel Lite Upright Vacuum

Should this portable vacuum cleaner be left recharging 7/24

And what portable vacuum cleaner would that be??? you dont have any name, make, model nor even a picture of it.\015\012\015\012On the other hand, leave it on the charger. What else are you going to do with it? If you store it on the was ... Vacuums

When it gets warm it cuts out then when left for a

What model dyson is it? If its the DC17 check the rubber seal inside the canister at the bottom of the cyclone where the bottom door comes up. if you see a gap between that filter and the bottom lid then dirt has passed through your filters and went ... Vacuums

How to tighten or replace roller belt on hoover

... Hoover V2 U8130-900 WindTunnel Bagless Upright Vacuum

Shark Steam Mop - Gray/ Purple Vacuum: I left water in the steam mop and now the steam is...

Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

When I vaccum, there is a dirt line left behind.

Your brush roller is dirty and your intake hose is clogged,there are three screws on the cover 2 to the left of the hose and 1 on the right side in the back that will take the cover off so you can clean the intake hose ,check your belt and remove the ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

I can't remove nut from end of vacuum.

The nut is reverse threaded . If you hold the fan with one hand use a ratchet to loosen the nut, you will have good enough leverage to break it, but if you don't then here's a little trick....Take your vise grip pliers and clamp it to the belt end ... Vacuums

We have the dyson upright. my 10 yr old son left

Sounds like motor has either burnt out or siezed can be fixed by motor replacement ££££ motor alone is about £45 not a simple DIY job. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0222 seconds