Having problems with your Vacuums ?

Shark/cordless /sweeper - over four years old. Started - but seemed like it was caught and shut off almost immediately. Not used year around - tried to start after absence. I have removed some hair and perhaps dental floss. Checked belt - it seems O.K. Do I need a new battery or is it just worn out.


Answers :

Check the brush,is there any dirt got stuck in between brush rolls.If there is then it needs to be cleaned.Your cordless sweeper will automatically shut off if an obstruction is caught in the brush roll. the other thing to checks is dust container.Check in case if dust container is full and its not got emptied.If the dust container is full then it needs to be emptied,other wise brush roll will not spin and unit will shut off.\015\012----------- But if all this things checked out ok then yes the battery needs to be recharged and checked.The battery needs to be charged for at least 4 hours to make the sweeper work,if the sweeper was not used for few months.But if the battery is not getting charged then the battery needs to be replaced.In some cases the battery charger it self gets short,so it does not charge the battery.To confirm that you will have to buy new battery and check.If the new battery is getting charged then charger is ok ,otherwise new charger also has to be ordered.The charger getting faulty is rare,but was noticed faulty in some cases.But if both charger and battery if they are working and still the same problem is noticed in sweeper then its faulty sweeper motor and controlling board.But this problem is very rare.As per the problem which you mentioned.the new battery should help.But you will have to confirm it by replacing battery.---------------- This will help.Thanks.Helpmech.\015\012
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Shark/cordless /sweeper - over four years old. Started - but seemed like it was caught and shut off almost immediately. Not used year around - tried to start after absence. I have removed some hair and perhaps dental floss. Checked belt - it seems O.K. Do I need a new battery or is it just worn out.


Check the brush,is there any dirt got stuck in between brush rolls.If there is then it needs to be cleaned.Your cordless sweeper will automatically shut off if an obstruction is caught in the brush roll. the other thing to checks is dust contai ... Vacuums

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems


Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?


Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

My bissell model 18Z6 has developed a loud noise and vibration when the brush is running. I have removed the brush assy and cleaned all the hair, etc but still the noise. I ran the brush motor with the belt disconnected and all seemed ok, but of course there was no load on the motor. I suspect a problem with the brush assy bearings or axle or both but I hate to just throw parts at the problem. any suggestions would be greatly appreciated.


... Bissell Vacuums

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

Generation 4 Apparently, my belt came off while vacumming. I had a lot of hari entwind on the roller, so cleaned off the hair.... but now I can't seem to get the belt to stay "in place". Is it supposed to move around on the brush? or be held in place? It seems to me when I try to get the hook to grab ahold of the belt, it is going tohe wrong way to grab it. Please HELP!


First off get a new belt, I am sure this one has stretched. Then put the belt around the brush roll, put it in the center, put the bottom plate back on. Then turn the big knob on the front and turn it until it locks, you will know if it grabbed the ... Vacuums

My vax swift 1600, has began to make a huge rattle noise, no noise when brushes and belt is removed. Seems like the belt is rubbing against the side. Wondering if there is meant to be a screw or something to keep the belt in place and it has come off.


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

I can't seem to get the belt cover off of my Kenmore Progressive 400. There are two buttons that say above "belt and bulb change" but the buttons do not move. Do you know how I can remove so I can put a new belt on? Thank you!


You have to take off the top of the power nozzel that has the light lense. There are two pressure locks,one on each side. Use a screw driver to release. You will see the screws.Take the two screws out and on some models, there are two pressure locks ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

I got a Eureka 4471 at a garage sale and I need to replace the belt but I can't seem to find where any screws are to remove anything to access the belt! Help!


Below I have listed a link for your models manual which has instructions and a link for the belt you need. Hope it helps you!Owner's Manual ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a Panasonic MCV7515 UPRIGHT VACUUM and need to remove the cowling that covers the brushes to clean the hair out of the bearings, but it isn't clear how that can be done without a crowbar or sledgehammer. Removing all the visible screws makes the hindmost part loose, but not the front half. Also, is there an easy way to replace the belt?


... Panasonic MC-V7515 Bagged Upright Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Could someone please advise how to remove the cover on a Vax Power Pet 2. I'm trying to change the belt, have removed the screws from the sole plate but the cover seems to be held in place by the


Go here > http://support.vax.co.uk/power-2-upright and download the manual with full instructions ... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

I have a roomba 551. Have cleaned and removed every bit of dirt and hair off it bu the brush cage won't close when the larger bush is put in. The cage will only click locked on one side, and the other side keeps hitting the brush and won't close. It's almost as if the bursh itself is not even, but this doesn't seem to be the case either. I've even tried removing the yellow rings, but makes no difference. Occasionally it runs fine, but most of the time the roomba just hobbles and clacks as i


Hi, had the same problem, it was like the main brush no longer fit into it's slot, so the brush cage would not latch. I discovered that the yellow bearing tip on the main brush twists off, and inside I found a lot of hair twisted around the pin. Th ... Vacuums

I have a kenmore upright 12 amp (M.N. 116.30003402C) vacuum that is not drawing anything up the hoes. There is no obstrution in the hoes and motor, belts, components are working, but there seems to be perhaps something missing(a part) or lost in the macinism that aids in drawing the air required to **** dust/dirt through the hoes and into the bag. Perhaps a diagram of parts and their function would help. Thank you.


... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??


... Kirby Vacuums

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?


Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

I have a Eureka 5902AVZ and the brushroll does not work. when i remove the belt, which is not torn nor worn out, the motor spins perfectly fine. Though when i put the brushroll back into place, it shows that the motor is trying to spin, but with resistance. it seems the brushroll will not spin if locked into place, because there is no attachment on the left side of the brushroll that will allow it to spin freely with the belt. am I missing some parts or is there something else wrong?


Hi and welcome to Fixya. I am Kelly. \015\012\015\012You have correctly identified the problem as the brush roll itself. \015\012\015\012There is a bearing under each end cap of the brush roll. You can gain access to the ... Eureka 5902AVZ Bagless Upright Vacuum

I have a power drive baggless vacuum cleaner...it runs well, but suddenly it seems to have lost most of the suction coming through the hose and floor area. When I remove the dirt container, the suction below it seems strong. I have had it to repair twice--they have tuned it up and replaced all filters and belt. It still does not pick up well when I vacuum or use the hose. Can you help ?


There is something stopping it up,you will have to dissasemble the unit to find the blockage,this is the most likely problem. ... Hoover U6660-900 WindTunnel Bagless Upright Vacuum

It sounds as though a belt is rubbing or slightly off-track. The sound is extremely loud. We've removed the plate around the brush bar, made sure the brushes are free of dog hair, and found that the belt appears to be on track. What should we try now? We haven't tried to use it to check for suction for fear of doing real damage! Thank you. Marcia VanDyne


Is the sound coming from the head unit where the belt is attached? When you power up the vac, can you watch the belt to see if it is frayed or running off track. I have the same Dyson and had this same issue, cleaning the head cured it, but your issu ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Dc17 -too much pet hair around the belt gears


I was having the same trouble and it was driving me nuts.  I tried cleaning and it did not work.  Then I tore the brush assembly off and looked up into where the little tooth gear is.  I saw something that did not look right.  The ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

For a Bissell Pet Hair Eraser the drive belt recommended is a size 8... is this right? It seems VERY small and difficult to replace.


No it does not use the style 8 belt. It uses the style 7/9/10/12/14/16 belt. You can view the manual and buy the belt here:http://www.vacbe ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

I need to remove the motor in my ricar 4812 (to change the axle) Where can i find something on that? I have 4 screws out- but it seems to be held into the body where the shaft goes out to the belt. Just missing something dumb.


... Riccar 4812 Vacuum

Bad smell after using my windtunnel for a couple of minutes i noticed an odd smell. i turned it over and checked, the belts are fine but i cleaned out the hair anyway. after doing that the self propel seems to struggle and it is hard to push. when i look through the window on the top i can see the brush spinning freely but then when i push it, it slows down dramatically and then picks up again. the suction is fine. what do you recommend?


It may be the roller bearings? ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0608 seconds