Having problems with your Vacuums ?

I want to install a new hose on a Sears vacuum Mod #116.23812300. How do I remove the Hose Connection Cover(#4370325)? It appears to be a flexible plastic part, however, it will not move from it's position on the old hose.


Answers :

Hi,
\015\012
\015\012Please CLICK HERE
\015\012This guide will explain you how to replace the hose.
\015\012
\015\012Goodluck..
You are trying to remove the flexible hose part from the end correct? If you post a picture of the item that would be very helpful since the numbers you posted really didn't help much.

Usually you can just take a flat headed screwdriver and pry out the old hose from the side of the connection piece. Let me know if I am not understanding correctly and I would be glad to help you.

thanks
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I want to install a new hose on a Sears vacuum Mod #116.23812300. How do I remove the Hose Connection Cover(#4370325)? It appears to be a flexible plastic part, however, it will not move from it's position on the old hose.


Hi,\015\012\015\012Please CLICK HERE \015\012This guide will explain you how to replace the hose.\015\012\015\012Goodluck.. ... Vacuums

Hose disconnected There is a clear circle on the part where the hose connects to the cannister (above the orange ball) that is in a position that has the hose disconnected. I can move the circle so that the hose connects, but it won't lock in that position. Help!


This video may help ... Dyson Ball DC24 Bagless Upright Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My dyson slim vacuum doesn't switch from hose to floor mode. I thought the foot lever was broken. I realigned it but it doesn't switch now from floor mode to hose mode. I take out the hose and I can see the white part. I thought it should move as you go from upright to recline position of the handle.


The changeover valve is not activating - call the Dyson helpline - they'll set you up for a repair with a repair dealer in your area. ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

I'm using Miele Medivac vacuum and I just sucked in a small plastic eye drop container by accident(I sometimes take off the brush part to **** in 'small enough' articles). And it is jammed in the part where the plastic hose connector bends. I think I can take it out if I can just disconnect the long necked plastic hose connector that connects the metal wand part and the hose part. Is it designed to be disconnected or should I not even try it?


I love the fact that the filter bleeped out s.u.c.k ha ha! ... Vacuums

Hi I’ve got a Panasonic vacuum cleaner MC E468 1600W a few years old now but works well up to recent problem. Not picking up I checked the obvious things and found excessive air being sucked in around the hose housing at the back of the vacuum (as it enters the waste bag) On inspection it appears to me as if there should be some sort of gasket that may have perished and been sucked in, however I can’t identify any such part. Any thoughts on what the problem/solution may be will be appreciate


The hose on the back might be loose - check to see that the hose is not obstructing anything where it screws in at the back - or indeed the screws may be loose themselves; some of the MCE 468 models had an additional ring washer that sits between the ... Panasonic Vacuums

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.


... Vacuums

I have the eureka bagless capture. The main hose is what I am interested in. I cracked the end of the hose where I would attach other parts such as the slim attachment for corners and to get inside the pillows in my chair, The part that I broke is on the very end of the hose. I had the plastic part clogged with some hair and during the process of getting it cleaned out, the part that I am speaking about is broken. Can you help me. I thank you, Mo moss


Change the hose part try a company called cds they r in the midlands but they courier parts\015\012out 2u dont have their no 2 hand u will need the model number try the\015\012web marting ... Eureka Uno 2998AZ Bagless Upright Vacuum

I have Optima, 12amp Eureka vacuum, Model 431, AXZ type and the extension hose for cleaning corners and edges --the plastic part that the attachments fit into has a piece broken off and tools don;t fit anymore. It looks like the hose attachment can be replaced--can it be and if so--where can I get a new hose attachment. It seems it is cheaply made of plastic and really shouldn't have broken a piece off.


... Eureka 431A Optima Bagless Upright Vacuum

Hoover SteamVac Model F6056-900 SteamVac/SpinScrub. Indicator light and high pitch suction noise indicates that dirty water tank is full. However, water level indicator (yellow bobbing plastic thing) is at the bottom of the tank and there is no water in the tank. Have check all the hoses for clogs, none found. Checked water port from motor area to receptacle tank for clogs, none found. Fixed broken hose to upholstery wand with duck tape, (wire not broken, just cracked plastic hose). The onl


There are 2 filters, make sure they are clean, one is on the tank lid, the other is from the bottom, it is red, pull it out and clean it. If yours has a foam filter on the tank lid covering the yellow ball, make sure there is at least a 1/4 in. gap ... Hoover Vacuums

My Eureka/The Boss doesn't seem to have the suction power it had. However, when I place my hand under the hose, it has good suction, then when I try to pull in a small particle, it doesn't, unless I have the hose nozzle completely over the particle. The vac is 10 yrs. old. I cleaned everything. Someone said the belt. Would the belt matter if the hose doesn't **** well? It is just old and worn out? It did shut off recently do to overheating. Help. Thanks. Lorraine


Doesn't "The Boss" Vacuum have a filter? Perhaps your filter is clogged and not allowing it to work properly. ... Vacuums

I'm using a Eureka maxima 12 amp vacuum and where the hose is connected to the vacuum by a screw that part is broken where do I find a replacement hose that includes the clear plastic part that I can attatch to the vacuum?


... Eureka 4700A Maxima Bagless Upright Vacuum

I need a Dyson DC 17 Total Clean exploded parts diagream that shows the switch assembly. There are two small springs and a small plastic part that were loose inside the switch assembly. This caused the vacuum to shut off in the full upright position which is the position you use when using the wand.


I don't have a full diagram for you, but I do have a photo of how they are meant to be assembled: ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Model UH60010, Series X12.0, Mfg code K09A. While attempting to use the hose and the extensions to clean shelves, my wife reported no suction. I removed the brush roller and the plastic piece just below where the hose opening is located and saw a "flapper" door that was closed and had some debris sort of jamming it. I removed the debris, but the door requires extreme pressure to open to permit the dirt, etc to moved up thru the opening , through the hose, etc. I thught maybe that somehow tg


Hello,Check to make sure\015\012the dirt canister is empty. If dirt canister is full, then you will \015\012experience\015\012reduced suction. Empty dirt receptacle.\015\012 Could\015\012 be a clogged hose - ... Vacuums

I have a kenmore progressinve 22813. The hose ripped at the swivel head. I purchased a new hose but can't separate the old hose from the swivel housing. How do I do that? do i need to buy all the swivel head parts as well? Thanks


Usually when you remove the hose from the swivel base and try to attach the new hose the attachment is usually not tight enough therefore the suction is always low. It is better for you to purchase the swivel head parts to enable you enjoy the use of ... Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum

I have an old Miele canister vacuum and I do not know how to disassemble the hose to check for a clog. I think it sucked up a nerf ball the size of a ping pong ball. I changed the bag but it did isn't appear to be in the bag. The vacuum powers on but I do not have suction with the hose, and since the hose has hard plastic elbow joints I do not want to pry them apart and break it


Hi Emily: If you have the model number for your machine you may be able to find your manual on the Miele website. Check ... Miele Vacuums

Suction I too have the same problem as Mr. Chief. I followed your advice and checked all the hose attachments, no clog. Tthe only one hose that the broom handle would not pass through was the plastic hose and there is a curve in that part. I did not want to force the broom in there as this is a new vacuum and is probably under warranty.


If you have a plumbers snake you can use that. But being under warranty, I would take it to Sears for repair. ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

I need to install part #PHP-236/C45ECUE. This is the connector in the top of the wand that connects the power to the brushes near the thumb switch at the end of the flexible hose. (Hope this makes sen


... Kenmore 22812 Bagged Canister Vacuum

Broken black plastic of hose handle where it meets the metal part


You are going to have to contact the manufacture google the name and model # and serial # appliance parts places wont stock the specific part good luck . Tom ... Karcher K DS 5500 Vacuum

Dyson DC17 Animal User's Guide says put plunger in out position. I cannot get the plunger to move and I'm not really sure if I'm trying to move the correct part. Cannot locate my user's manual for help.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have an old Shop Vac model 3331.5. This is a 12 gallon 1.5 hight peak shop vac with a detachable blower. After many years I decided to use the blower feature, but have lost the lost the manual. Question; how do I attach the hoses to the blower? The motor has that cap on it the direct the flow of air in one direction and the wide hoses do not fit over it. I may be missing a part, but I would think the directional cap would have to come off anyway.


Remove the cap that directs the air and insert the hose in there. ... Vacuums

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o


I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

I have lost the manual and forget how to use the hose part of vacuum, also the handle turns and is not secure ( that is the handle in the upright position). It is a bagless Stick Shark Vac. I need to know how to attach the hose to the vac so I can clean furniture and corners.


... Euro-Pro V1828 Shark Stick Vac Bagless Vacuum

Rainbow shampooer The soap dispenser on my Rainbow is not dispensing soap when I flip the switch to 'soap' mode. All connections are intact. All plastic hoses are intact. What do you think is going on? The soap bottle connects to a little straw that appears to be free of obstruction, however, it connects into a sealed casing on the hose.


The little "wash/rinse" switch on some of the Aquamate units shuts off the soap flow by kinking the tube inside the housing. If you leave the switch in the rinse position (therefore, kinked) when you're done using it, it may dry in the kinked positi ... Rainbow E series Canister Wet/Dry Vacuum

I have a tear in the hose of my old model # F6030-900 unit which doesn.t allow water from the attachment to **** back into dirty water bucket. The model #F6039-900 is the same model # but different year I understand. The tear is at the bottom where set the recovery tank in the lay down position and can look in the unit at the bend of the hose.


You will have to replace the hose asm. You can order online at: \015\012http://vacuumsuperstore.com/F6019.html\015\012\015\012H-90001334 (43 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0859 seconds