Having problems with your Vacuums ?

GOT REPLACEMENT PART ( THERMOSTAT p170-97) FOR COFFEE URN REGAL WEAR 58001R MODLE. NEED INSTRUCTION AND DIAGRAM ON HOW TO REINSTALL THERMOSTAT


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

GOT REPLACEMENT PART ( THERMOSTAT p170-97) FOR COFFEE URN REGAL WEAR 58001R MODLE. NEED INSTRUCTION AND DIAGRAM ON HOW TO REINSTALL THERMOSTAT


... Vacuums

I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.


Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My mother purchased a replacement hose assembly for a Bissell ProHeat 2X and the part was shipped without any instructions... While I am pretty handy, my issue is with the supply tube, and I cant figure out how to accomplish the replacement, and as its not MY vacuum, Im hesitant to start taking things apart.I just need instructions to replace the entire hose assembly.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Need to open rotating brush part of vacumm as motor functioning but roller not turning...perhaps belt broken put need to get into ..inside brush box ...Need help need instruction with diagrams Thanks for help Robert


... Panasonic MC-V9638 Bagged Canister Vacuum

Need to replace Dyson DC17 Cleaner Head Assy, Part Number 912276-01, are there instructions for this task?


... Dyson DC17 Animal Upright Vacuum Refurbished

I think the pump needs to be replaced in my Bissell little green machine. Some water/solution is being pushed through but not enough to spray only drip, if I hold the machine up high while using it (ie on a table) it will spray a little. Is the pump easy to replace? is there anywhere to get a parts diagram?


I got my Little Green ProHeat when the product was first unveiled\015\012several years ago. Shortly thereafter, the nozzle itself developed a\015\012clog in the spray jet. Remove the nozzle from the end of the hose, and\015\012with the machine runn ... Bissell 1400 Little Green Pro Canister Steam Vacuum

I need instructions to replace a diverter door on a Bissell 1698 Power Steamer Proheat carpet cleaner. I already have the replacement part


Hi,Download the Service Guide that would have all the information :-http://www.managemyhome.com/mmh/lis_pdf/OWNM/99040364.pdfHope i helped you.Thanks for using ' Fixya ' and have a nice day!! ... Vacuums

Need parts diagram for euro-Pro ep601. I need to replace the power cord, but cannot get the motor gasket guard off.


Hi!You need to release a "clip" under the handle(this is on top of the dust cup) and then look for a hidden screw right under the thermostat label. ... Vacuums

I just recived a free Kirby G3 vacuume. the only problem is the on/off switch dosen't work and someone took it apart before i got it. all of the parts are there as far as i can see but they did not label the wires I need a diagram to be sure that i replace them correctly. Where can I find one?


... Kirby Generation 3 Bagged Upright Vacuum

I bought new belts to replace the old ones (one had broken and the water would not feed) My cousin took it apart and now I need to put the new belts on and get it back together - do you have instructions or a diagram?


There are different variations with Bissell. They have the ProHeat series and a Power Turbo series. Below is a link with instructions and diagrams for the Belt Access Door. If this doesn't solve your problem or isn't the correct model, please post ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have cleaned the filters on my dust buster. The vacuum works for a minute then the battery seems to wear out and the power weakens until it stops. How do I replace the battery on this vacuum? Do I need just one 9.6V battery? What screws do I loosen to insert the battery? I can't find my instruction booklet. Tank you for your help.


... Black & Decker 15.6 Volt DustBuster Vacuum

I have a Hoover Vacuum Cleaner, Runabout Supreme, on which the belt has broken. I purchased a new belt, part number 38528-040. I need some instructions on how to install the replacement belt? Thank you. JBS


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=728341\015\012Generic problem for all Vacuums\015\012I have a Hoover Vacuum\015\012Posted by Jimbob48 o ... Hoover Elite U5061-900 Bagged Upright Vacuum

Need instructions to replace PN 8191782 on sears canister model 11625615506. Can you send direct, my computer will not open the Diagram you have on the web


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

I have a Kenmore Progressive model 116.22812204 purchased 2003. The swivel (part nuumber 8195133) that attaches the extension wand to the power mate attachment snapped, so I can't keep the parts connected. I can order a replacement part on-line, but I don't know how to replace it - is it difficult to take apart the power-mate and replace this part? Do you have instructions on how to do it? Thanks!


... Kenmore Vacuums

I need a replacement Powermate Canister Vac HEAD...part number for model 116.27614701?


... Vacuums

Parts diagram I have taken the assembly apart and I would like to see a diagram in order to know the part numbers that i need to order for repair.


You may like to try here see if yours is listed http://onlinevacuumparts.com/s-3-bissell-vacuum-parts.aspxriz. ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Hi, does anyone have the instruction diagram for the DeLonghi EC750 coffee machine? I have the instruction manual minus the page which shows diagram/ description of parts. Thankyou!


I think these PDFs at the link below are what you're looking for\015\012\015\012http://web1.dlservice.o ... Vacuums

How do I replace the Powercord on a Fantom XT64K Vacuum. The powercord shorted where is comes out of teh housing. I need to open up the unit & replace but need a service manual of instructions. Thanks Father Lenny


I have done this several times, it's some what simple just take the unit apart and use the old diogram to replace the new one. Or take a digital photo of it opened so you have your own scematic. You should be able to purchess the cord at your local h ... Vacuums

Need parts Anyone know where I may find replacement parts for this cleaner? I also need a manual. Thanks


Go to this site they have the schematic and replacement parts.\015\012http://www.hescoinc.com/vacuum_cleaner_parts/bissell.html ... Bissell 1631 PowerSteamer ProHeat Canister Vacuum

I HAVE LOST MY INSTRUCTION BOOK FOR THE STEAM VAC SPIN AND SCRUB. I WANT TO USE THE STAIR ATTACHMENT, BUT I CAN'T FIGURE OUT HOW TO HOOK IT UP, OR OPERATE IT. I SEE WHERE THE PLUG IN PART GOES IN THE FRONT OF THE MACHINE, BUT I CAN'T GET THE OTHER PART TO SLIDE INTO PLACE ON THE FRONT OF THE RESOVIOR TANK AFTER I REMOVE THE FRONT PANEL, AS THE DIRECTIONS ON THE FRONT OF THE RECOVERY TANK SAY TO DO. THE FIT IS JUST TOO TIGHT. WHAT AM I DON'T WRONG- OR HOW COULD I GET A REPLACEMENT INSTRUCTION BOO


You can download a PDF version of the manual at the link below. I believe you can contact Hoover as well and they might mail you one.http://www.hoover.com/CustomerService/Manuals/Default.aspxGood Luck! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,


You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

Parts diagram where can i get a parts diagram with a break down of the vacuum, for a dyson dc07 we need to do some work on ours


You can find the exploded views and replacement parts at www.searspartsdirect.com.Go to the link and enter DC07 in the field for Model number. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The solution stick inside the handle needs replaced and I would like a new face plate. I have the model numbers (38458-031 & 37275-011), but can not locate the replacement parts. This machine is more than 10 years old and works like brand new. I can not see throwing it out and want to fix it. Please help me locate these parts. Thank you!


... Hoover Steamvac F5860-900 Vacuum

I need diagram of replacing on/off switch for Oreck XL2600


Manual would not, they want you to pay a service tech.\015\012\015\012Believe this model has switch in grip, \015\0121. Unplug unit.\015\0122. remove screws from grip.\015\012separate the grip halves to access switch. ... Oreck XL2600 Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0875 seconds