Having problems with your Vacuums ?

Bissell Proheat does not spray water along cleaning brush. Seems to spray just down either side only.


Answers :

Are the brushes turning? If not then that could be your problem. If they are, check the spray nozzles, they may be partially clogged. Try water a mix of vinegar and water thru it to see if it will unlog your kines and spray nozzles.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissell Proheat does not spray water along cleaning brush. Seems to spray just down either side only.


Are the brushes turning? If not then that could be your problem. If they are, check the spray nozzles, they may be partially clogged. Try water a mix of vinegar and water thru it to see if it will unlog your kines and spray nozzles. ... Vacuums

I have a roomba 551. Have cleaned and removed every bit of dirt and hair off it bu the brush cage won't close when the larger bush is put in. The cage will only click locked on one side, and the other side keeps hitting the brush and won't close. It's almost as if the bursh itself is not even, but this doesn't seem to be the case either. I've even tried removing the yellow rings, but makes no difference. Occasionally it runs fine, but most of the time the roomba just hobbles and clacks as i


Hi, had the same problem, it was like the main brush no longer fit into it's slot, so the brush cage would not latch. I discovered that the yellow bearing tip on the main brush twists off, and inside I found a lot of hair twisted around the pin. Th ... Vacuums

I have a Janome QC 6125 which has been sewing beautifully. I have just cleaned the lint from around the bobbin area and now it isn't sewing at all well. The bobbin side seems to be ok except there are loops of the top cotton protruding through the bottom side in irregular intervals. The seam does not seem to be strong either.


... Vacuums

My brushes on my hoover streamvac will not rotate. I removed and cleaned assuring that the filter was also cleaned. The only different thing I have done is to insert the upholstery attachment and removed it after use (didn't work so well) suction seemed weak. I am also noticing that there is air being blown out of sides where the dirty water container is. (don't recall that in the past).


... Hoover F5900-900 Upright Steam Vacuum

I have a Bissell 7920 ProHeat and only used it 4 times and the brush on the bottom has stopped spinning and when attempting to spray solution the flow indicator doesn't spin and nothing comes out. I have looked at all of the belts and they seem fine. I have also removed and cleaned the heating unit. Still nothing. Any other ideas?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Hello. My dyson dc04 keeps making a loud screeching noise when im vacuuming. It seems as though the plastic from the brush is catching on the plastic on its holder either side of the belt. Is there any way of fixing this problem?


Remove base cover by 3 'screws' 1/2 turn anti clockwise and clean well remove fibres replace cover and re try. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have used my Steam Vac for carpeting, but until today, had never tried cleaning upholstery with the spin-scrub brush. I spent a miserable afternoon trying to control the spray, which seemed to go everywhere AROUND the furniture, but not ON the furniture! Additionally, I never did get the water into the recovery tank, despite many attempts to connect and re-connect the hoses and recovery tank/lid.


I can sympathize. My vac came with two handheld attachments. I have better luck with the handheld attachment that doesn't have the spin-scrub pads. To keep the water from going all over the place, you need to keep the part the you hold only about 1 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?


Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)http://64.49.205.183/v/u6451900.pdf ... Vacuums

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge


... Vacuums

I cleaned out my brush in the bottom front, cleaned out the small tubing going into the canister, and the canister itself. I also changed the filter.I snapped everything back into place, but Since then, it doesn't seem to have any suction and there seems to be a space between the canister and the bottom of the vacumm where the canister sits. At that area, you can feel air coming out when trying to vacumm and it just doesn't pick up, it seems to be just blowing stuff around.


You need to really look at it some thing is out of line you shooed not have\015\012any spaces in the top or bottom\015\012pull the canister back out and look at the pins that you lined up with the\015\012to ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.


It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593. ... iRobot Roomba 4000 Bagless Robotic Vacuum

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.


Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

My Oreck XL upright is blowing out instead of sucking in. I changed the bag and cleaned the brushes; I also cleaned out the main "pipe." I looked for a place to change settings and couldn't find any, so I know I didn't inadvertently switch something. The brushes seem to be spinning at the correct speed. Thank you, Julia Byrem


... Oreck XL2200 Bagged Upright Vacuum

My dyson dc07 brush bar seems to be only spinning at half speed. Leaves three light streaks in the vacuum marks like somethings just dragging. Brush bar is clear and filters are clean. Seems like there's slipping somewhere.


The belt is stretch and so it is slipping on the motor shaft. You need to change the belt. Here is a link for the\015\012instructions on how to change the belt and a link for the belt you need: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

5 yr. old Miele s514 Turbo plus's power nozzle brush seems to disengage temporarily, stopping the spin. Then it seems to re-seat itself after a few seconds, then starts spinning OK. I keep the nozzle brush very clean, so there is no hair or yucky stuff to cause it to jam. Please help.


I had a White Pearl with same problem. As I moved the hose/wand the brush motor would start stop. Find out where the circuit opens up by holding one part and moving the part that connects to it - 1) where the hose plugs into the cleaner, 2) the swi ... Miele S514 Solaris Turbo Plus Vacuum

I noticed that the little side brush doesn't turn anymore and the Dirt Dog stops about every minute now so I have to keep turning it back on! I have dismantled the brushes and cleaned everything out but that didn't help at all. It doesn't really come apart any more than that for cleaning. Any suggestions as to where my problems may lie?


... iRobot 1100 Dirt Dog Bagless Robotic Vacuum

Brushes on Hoover Steam Vac F7441-980 do not turn.Brush control on;drive pin present;filter intake clean; Drive mechanism doesn't appear to be turning. Also when spraying on cleaning solution, spray comes out in streeks rather than the width of nozzle. JBB


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My bissell model 18Z6 has developed a loud noise and vibration when the brush is running. I have removed the brush assy and cleaned all the hair, etc but still the noise. I ran the brush motor with the belt disconnected and all seemed ok, but of course there was no load on the motor. I suspect a problem with the brush assy bearings or axle or both but I hate to just throw parts at the problem. any suggestions would be greatly appreciated.


... Bissell Vacuums

I have a nearly 9 year old Electrolux Excellio Z5228 vacuum cleaner. It has recently started cutting out during operation. I cleaned the micro filter (between bag & motor) via brush & hitting against wall & seems / looks quite clean. I washed the gore filter (output from motor to clean the exhaust air) as per instructions, then let to dry. It was very clogged but now very clean. The vacuum clearner still cuts out often. Even after a long rest (say overnight) it still won't start, then ano


... Electrolux Vacuums

Dyson Ball DC24 brush turns but is loose and makes a very loud noise. Brush seems to be hitting sides of vacume.


You need a new brush and end cap. The brush and end cap can wear or break in time as they are made of plastic. Spares available on Dyson web site. ... Dyson Ball DC24 Bagless Upright Vacuum

Does not spray or wet surface im cleaning doesnt transfer water from one side to another


... Bissell SpotBot Robotic Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0716 seconds