Having problems with your Vacuums ?

HOW TO REMOVE SOLEPLATE PLEASE TO CLEAN cleaner dyson dc07


Answers :

On the underside of your Dyson, there are 3 coloured fasteners with slots in the heads which secure the sole plater. Turn each one 90 degrees with a coin or large flat-bladed screwdriver and then lift the edge of the sole plate where the fasteners were located. It can then be removed. If your Dyson is yellow/grey, the fasteners will be yellow. If it is purple/grey, the fasteners will be purple, etc.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

HOW TO REMOVE SOLEPLATE PLEASE TO CLEAN cleaner dyson dc07


On the underside of your Dyson, there are 3 coloured fasteners with slots in the heads which secure the sole plater. Turn each one 90 degrees with a coin or large flat-bladed screwdriver and then lift the edge of the sole plate where the fasteners we ... Vacuums

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Removing filteron dyson dc07 if stuck


Hi its Darran at Dyson.We would recommend trying to twist the filter in the casing until it becomes loose. Sometimes, there can be a small build up of dust around the edge of the filter which can make it difficult to remove from the casi ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How do you remove the HEPA filter on Dyson DC07


I use a screw driver to pry them up.\015\012Joe ... Dyson Vacuums

Dyson DC07 Filter Release Catch removal


If its the part im thinking of its a small spade like catch thats glued into a hole in the chassis normally id lay the machine on its front and gently tap the old catch out with a flat end screwdriver and a small hammer be carefull its very brittle ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC07 The plastic pre filter catch snapped on my Dyson. I have a replacement already, but can't figure out how to remove the bottom of the broken one. It looks easy enough to slide/snap the new one in but accessing the old one isn't easy. What do I need to do to get it out?


Turn your dyson over so you can get to the bottom undo the screw and then you can see the bottom of the clip a gentle tap with with a screw driver blade will knock it out and the other one slips in ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Nedd PDF file of DC07 Hepa+ please. - Dyson DC07 Bagless Upright Cyclonic Vacuum


Here is a link to the PDF manual http://media.dyson.com/downloads/us/floorcare/manuals/dc07_opmanual_usa.pdf\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC07 My DC07 cuts out after 5 mins and I want to replace the thermal cutout. I have cleaned it thoroughly, including the cyclones but it still cuts out. How does the plastic moulding around the motor dismantle? I have started by removing the 4 torx screws but the upper grey housing does not want to detach and I am worried about breaking the plastic. Appreciate any advice.


Try this page: -http://www.fixya.com/support/t192124-overheating_dyson_dc07Regards Gualo ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Need to remove the clutch on my Dyson DC07 animal and I can't get the clutch cover off. All the videos look like it should come off easy after removing the three screws.


... Vacuums

Replacing the on/off switch on Dyson DC07. After the switch retaining screw is removed, how is the switch removed? Does it just pull out or are there retaining tabs ?


Have a look at www.dysonmedic.com which has some great info on your machine ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Remove Motor How do I remove the motor from a dyson DC07


Try the second section of my post on this page: -http://www.fixya.com/support/t192124-overheating_dyson_dc07Hope this helpsRegards Gualo ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC07 Filter Release Catch removal


Yes sorry i know what mean you need to remove the motor casing to reduce the risk of breaking any parts. Lay dyson on the front and remove the bottom plate and roller bar. Now you need to remove the belt from the motor pin lay on left side look t the ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Why won't my dyson DC07 Animal turn on when the wand is removed?


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Removing the filter on Dyson DC07


On the 07 model it is on the right side push clip and pull inside will be a foam filter wash and dry ... Dyson DC07 Bagless Upright Cyclonic Vacuum

RE: DYSON DC07. Cleaning the roller I removed one end and cleaned it. Cannot get the roller back on the vaccum. If you could give me instructions on how to do this I would be very appreciated. Thank You


Try this link. http://www.sparesaver.com/help-and-suppor ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

My dyson DC07 upright vacuum makes a loud noise when I turn on carpet mode. I removed he bottom plate and checked the belt and it looks ok


Did you check the roller brush to make sure it was clear of debris? ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC07. Problem:- switch the hoover on and it cuts out after approximately 1 second. Any ideas please?


The motor has a built in over-current trip to protect itself (and you if it seriously overheated and caught fire). This normally automatically resets itself, however if the motor has just about had it, the moment it is switched on, it just trips agai ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Changing belts on dyson dc07. removed 2 screws from belt cover why will it not come off?


You will need a special belt tool. you can buy one on ebey for $15 bucks. do not try to your hands as the belt is very tight. ... Dyson Vacuums

My dyson dc07 works fine for about 5 to 10 min then turns itself off leave it for 10 min or so then it will work again for a bit then does it all over again. help please thanks


Your machine is overheating. This is usually caused by the dust bin being too full, your filter is long overdue for a cleaning, or there is a clog in the machine. Usually a cheap fix regardless... Wash your filter, check the removeable parts for bloc ... Vacuums

I have a Dyson DC07 animal ( purple). If you are standing behind the vacuum I am missing the lower righthand connection...therefore whatever is suctioned up comes out at that point just over the back wheel. I would like to purchase a replacement for this part. In the manual I believe this part is labeled as C. Can this part be purchased separately ?Please Help....


Hi there SmartAlec from NelsonVacuums.com.au i am not sure if you are based in australia but if you are you can ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC07 vaccum, the clutch has gone out of it and can't figure out how to remove it


Hi,\015\012\015\012Check out this video on Youtube http://www.youtube.com/watch?v=7_CtaFcc5HU\015\012 \015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc07 bottom hose how do i remove it - Vacuums


... Vacuums

Removing dust bag - Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum


There is catch on the top ... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum

The bottom of my dyson dc07 original is not sucking and the roller is not rolling but the hose is sucking and i have cleaned the whole thing PLEASE HELP ME!


U need a new clutch assembly\015\012refer to this site for more details on dyson vacuums and to submit a repair form\015\012\015\012D ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson vacuum I have a DC07 vaccuum. The problem I am having is that the front does not want to stay down as I vaccuum and I continuously have to keep stepping on the front to make it go back down to the floor. It seems as though there is either not enough weight in the front or possibly the unit just has to be broken in so that there is not so much resistance between the handle and the front of the vaccuum. Could there be something I did not remove or is this typical on these vaccuums?


There is some thing broken it is two plastic cogs they help the front go down and stay up you will have to get a star screw driver and there should be two screws on top and two at the b ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0708 seconds