Having problems with your Vacuums ?

How do you get the old empto and boot off to replace it? Its a G4 Kirby...

Answers :

Cut the strap that goes around the boot there at the bottom of the bag. Work the rubber seal off, then you can cut the strap holding the bag tube and then you can pull the emtor off.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you get the old empto and boot off to replace it? Its a G4 Kirby...

Cut the strap that goes around the boot there at the bottom of the bag. Work the rubber seal off, then you can cut the strap holding the bag tube and then you can pull the emtor off. ... Vacuums

I have a Kirby Heritage II which normally works amazingly well, but it's not playing at all nicely today - and of course we have apartment inspections tomorrow. *dies* The belt broke today (as did the replacement belt, which I'd bought at the same time, so apparently the rubber was old), so I went over to Stark's to get some new ones - but it still won't cooperate. I've taken the head apart and put it back together several times, to be sure that everything is properly seated, but it's just not

... Kirby Heritage II Vacuum

The bag latch on my Kirby Generation 3 broke. How do I get the old one off to replace it

At the bottom of the bag, there is a zip tie around the plastic part that turns & snaps on to the exhaust hole of the vac. also take a flat screwdriver & pull up the rubber under the zip tie...all the way around, like u would take a bike tir ... Kirby Generation 3 Bagged Upright Vacuum

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.

... Vacuums

Need a replacement on/off switch for Dirt Devil Deluxe Model 8201 (more than 12 years old). We have the old one out. We just need a new one to replace it. Where can we get one?

... Dirt Devil Vacuums

Hi There I have got a Kirby 2 HG vaccum cleaner which is around 20 years old now. It was going really well until last week when one of the capacitors which are connected to the brushes blew up. There is two capacitors one for each brush. One of them completely blew to bits and the other one is still intact. My question is are they the same size and where do I get a new one from. I know it is an old machine, but I would like to fix it and get it going again. Any tips???

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=541405\015\012Generic problem for all Vacuums\015\012Hi There I have got a\015\012Posted by opfinder on Apr 24, ... Vacuums

Belt replacement i am trying to replace the belt on my kirby g4 and i can not get the rooler off to replace the belt. if you could tell me how to do this it would be great.

Lift the light bulb housing up and you will find a latch that will rotate to release the front agitator housing and remove it from the machine. On the bottom of that housing, there are two latches that secure the bottom plate that covers the roller. ... Kirby G4 Bagged Upright Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

How do I remove the collar to replace the cord to the power bar, I have the part, cannot get the little collar off to connect the new wire, purple to white and white to black... cannot get the old wir

... Hoover Powermax S3530 Bagged Canister Vacuum

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr

Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Last year my wife and I bought a new Dirt Devil Reaction All Surface vaccuum cleaner to replace the older Platinum Force. After using it a couple of times the new one gets clogged with dog hair easily and shuts down. I cleaned it out completely including the hepa filter but it will not handle the dog hair. The old one never had a problem and still works. We went back to using the old vaccuum cleaner because we can not find the receipt and had not registered the new one and are stuck with a new 1

Greetings jettin_us,\015\012\015\012Normally you can contact the store you purchased the unit at, and if you paid with anything other than cash, they may be able to retrieve your receipt for you. \015\012\015\012Once you get t ... Vacuums

How do I get a replacement belt for my DC 17? We sucked something up and broke is so I do not care if it costs anything, I just need a belt for the beater. How do I get one? unfortunately my wife also through out the old one with a part number on it,....

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dear Sir/Madam, My old faithful Hamilton Beach Mixer, now 60 years old, is still working but recently I was told by someone who looked at the motor that it needed repair or replacement. Is it still possible to get it in working condition?

If the armature shaft is worn there might be a problem, but that would be about the only one, Bushes/bearings can be replaced as can brushes. If the armature shaft is worn, a fix can be formulated but it will require some ... Vacuums

Hi On a Hoover convertable model U4497-900 I'm trying to replace the fan. The old fan cracked, then flew apart. I have the new fan, have the motor assembly removed, but can't seem to get the pulley nut off the motor to replace the fan. Is there a trick to this or should I just try to muscle it? Thanks.

... Vacuums

Kirby My Kirby is less than a year old.  It's suction is no longer strong. I tried cleaning the hose and even replacing the bag.  Do you have any other suggestions.  By the way, I have the Sentera model.  Thank You

Here is a link to my online troubleshooting guide. Hope it helps...\015\012\015\012http://r ... Kirby Generation 3 Bagged Upright Vacuum

Need a replacement drive belt for my hoover lark u4043 not sure about last no. it's an old machine, but this one is in perfect condition, minus the drive belt. my local vacuum specialist says they can't get them anymore. where can I get one or a suitable alternative?

HiAs you know the Hoover Lark was more or less a rebodied Hoover Junior. The U4043/ (are you sure its not U4034?) model should use the same round drive belts as the Hoover Junior 1346 so youre looking for the old rubber ring type belts which ar ... Vacuums

Fan replacement I have to replace the fan on my g4 how do I get the old fan that is worn and broken off the shaft,,thanks for any help that you might be able to give

Detailed instructions on fan replacement HEREGoodLuck,Rocky:-) ... Kirby G4 Bagged Upright Vacuum

How to replace just the Kirby 210097 Hose End For G5 Series Vacuum Cleaner to hose. can buy replacement but can not get the broken end off

Simple and rquires no tools. Fill your sink with hot water and set the end in water with attachment on it. Within a few minutes the end is soft enough to slip out. setting the hose end in the water again will let you simply slip the hose into the ... Kirby G5 Bagged Upright Vacuum

I have a 144w305 long arm industrial sewing machine i am looking for a bobbin case to replace old one. i am getting alot of skips and was told i need to replace this. any suggestions. thank you

... Singer Vacuums

Kirby G series drive unit needs replacement. Where do I get a unit at the best price

Try eBay or Craig's List. You can get a lot of good deals for that model. I've looked, and there's deals for like $5 to $15. ... Kirby Vacuums

Cant get the suction impellar off to replace - Kirby Generation 3 Bagged Upright Vacuum

Shaft has to be spun clockwise. It has reversed thread. If this is not the problem but you just need to somehow hold the field - see instructions HERE. You may ... Kirby Generation 3 Bagged Upright Vacuum

I have a 15 yr old electrolux genesis upright vacuum cleaner that I can't get the roller out, to replace the belt.

Fip it upside down and hit the roller with a malett\015\012\015\012http://evacuumstore.com/c-99-electrolux-belts.aspx?manu ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

I broke my kirby generation 3 vacuum cloth bag latch i found where to get the part but how do take it apart to replace it

... Kirby Generation 3 Bagged Upright Vacuum

I can't get the shamooer brush re-installed back on my Kirby Sentria after replacing the belt.

Try this link for a step by step guide...http://reviews.ebay.com/KIRBY-CARPET-SHAMPOO ... Kirby G6 Bagged Upright Vacuum

Hoover F6028-900 Need to replace the hose assembly but am unsure of how to get the old one disconnected.

It's probably harder to explain than it is to do. \015\012\015\012Take off the recovery tank and underneath it you can see where the hose attaches to the unit. On the bottom side of that inlet is a clip that latches the hose ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0780 seconds