Having problems with your Vacuums ?
I need an manual for turboglide steam iron. It is stilln new but when plugged in only the standby sign goes on. What must be done to warm it up.
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I need an manual for turboglide steam iron. It is stilln new but when plugged in only the standby sign goes on. What must be done to warm it up. Thank you
There's a burning smell when I plugged it in. I read the manual and it said I must plug into the grounded outlet. I have done so and am still scared that i am smelling the burnt smell
The grounding usually doesn't have anything to do with something cooking. If this is new, take it back for replacement. If it is out of warranty, check the bottom for a locked-up brush assembly/burning drive belt (motor trying to make the brush turn) ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Hello. My scooba 5800 had a check tank light on. I used a straw on the valve and that fixed the problem. Now the scooba runs like nothing is wrong, but there is no actual cleaning going on! It goes the full cycle, but no liquid comes out. The vac part seems to be working b/c there is fluff in the vac when it's done. Please help!
Hello, Take the battery out and hold the switch down for 30 seconds, to reset the curcuit board, then charge back up for 12 hours. this should take care of it. If I can help future please call @ 1561-848-3387 Thank you, Teresa. Clean Sweep Vacuums ... iRobot 5800 Scooba Vacuum
Need instructions how to use Hoover Steam Vac Spin Scrub. I borrowed it from my Sister and she left it with no instruction book or letting me know how to operate it. I put water & cleaner in top tank. That's all I know to do. Do I put any water in bottom tank? I figured not, since that is probably where the water goes when sucked up by vac. Do I leave lid on bottom tank? I usually use a commercial cleaner, and this is very different. I need to know NOW, as I must return it to her today, and I'm
I did have a solution in just a few minutes. Someone responded with a solution that gave me the website where I could go and print the manual in pdf, so did that, and checking instructions I was able to clean my carpets and get the shampooer back to ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T
... Rainbow E series Canister Wet/Dry Vacuum
Shark steam mop power light goes on, basin feels like it is getting warm, but there is no steam or water released. Pad is completely dry. What's going on.
Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
I am cleaning the hose to the underneath of the vacum. It is clogged. I need a picture from the manual to show how it all goes back in after i am done. I have a dirt devil quick power compact.. UD... something I have been looking for the manula online. unable to find it.
Go to the website below. Search for your product; either by model number of by type. When you find your model the parts page will also include a link to the manual.\015\012\015\012 ... Dirt Devil Vacuums
Pfaff Creative 1459. When trying to wind a bobbin, I do what I've always done, turn the small round "wheel" on the right, slide the bobbing into the little knob that keeps it in place and gently press the foot thing on the floor that should start the bobbing to winding. The bobbin does not turn at all causing a loud whirring sound and the needle goes up and down as if it were making stitches. I finally got some thread onto the bobbin but it is not smooth and looks like a spider. I really nee
I have a self propelled Royal Dirt Devil vacuum model number 087900 and it goes backward fine but forward has to be pushed so hard it's impossible. Is this a switch? Do you know about how much the part would cost and can it be done by a beginner. We fix a lot of things ourselves but we aren't mechanics by no means. We put a brand new belt on it. I don't think it can be put on backwards and brush turns fine. Where is the switch? Use layman's terms.
You might try a new belt and/or brush roll. The brush roll is what helps pull a vacuum forward, the power drive helps, but if the brush isn't turning like it should, then it will hinder forward motion. The belt may look ok, but they stretch to the ... Vacuums
Roomba 560 just goes in a small circle, will not go forward or backwards, then a red alert lights up ststing to clean it, which a throughly good cleaning has been done, gave this as a gift to someone and they only used it for a short time before this happened, any help to solve this would be appreciated
... iRobot Roomba 560 Robotic Vacuum
My roomba goes round in circles. sometimes it stops and moves a centimeter backwards and then again it goes round in circles. if you press the ,,dock'' button it goes back to the station. if you press the ,,clean'' button, again, it goes round in circles.... the machine is cleaned, the sensors aren't covered with dirt, the weels and brushes can rotate freely.... can anybody help me??? thanks in advance franz
Here's the link. IR Bump Sensor Fix ... iRobot Roomba 560 Robotic Vacuum
Vacumn loses power when on. goes on and off.
Hi!\015\012I think you need a new power cord. If you have a Kirby, here is a helpful link...\015\012\015\012 ... Electrolux Central Vacuum
Wife took Dyso DC 26 Handle Wand off the Vacum. Can't Figure How to Put It back Together!? We Must B STUPID!
This link below is for the manual that will give you full instructions how to replace the hosehttp://media.dyson.com/downloads/UK/floorcare/Manuals/ ... Dyson DC26 Bagless Canister Cyclonic Vacuum
My h20 mop+switches on and the heater warms up but does not make steam, also the green light stays off.
Self propelled vac: goes great on hard floor or hard slick carpet. Goes backwards fine but will not pull itself forward very well. Requires some effor to push it forward. I have adjusted the cable so the lever on the motor goes as far forward as possible. Suggestions? Model U6446-900
Dear Nasherrill,\015\012\015\012I've found a friend! I thought I was the only person in the world who owned the Hoover Model U6446-900! This model does not appear on the http ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Im trying to put the peice back together that goes under the tube that hold the water the part that goes into the hole in the vacum.. i took it apart because its not spraing right to see if it was cloged.. and now im not sure how it goes back together.. can you please help me.....
I tried to find a service manual for this, but came up with only a exploded view diagram:\015\012\015\012http://ineedbags.com/images/b8920.jpg\015\0 ... Bissell 8920 ProHeat 2XTM Upright Vacuum
I am putting my bissel 8910 back together and behind the motor there is a black 3-way tubing connector. One side goes to the pump discharge, one side goes to a tubing going to the right rear wheel (facing the unit from the front) I don't know where the third side goes to. I do not seem to have another tubing for this one to go to? Maybe it is lost or ?
Hi, its hard to know what its for without seeing it. The best way to test this is to start the machine and vacuum a part of the carpet/ floor. Then let me know wht the vacuum is not doing. This will narrow it down. Please, get back to me. This sounds ... Bissell 8910 ProHeat Clear View Upright Vacuum
While replacing my power cord on my DC25 a spring popped out I have no idea where it goes. I need a diagram so I can see where it goes
Here is how the switch assembly should go together: ... Dyson DC25 All Floors Bagless Upright Vacuum
MY NEEDLE GOES DOWN TO PICK UP BOBBIN THREAD AND SEEMS TO HIT SOMETHING SOLID. IF I TAKE THE NEEDLE OUT IT GOES ALL THE WAY DOWN. pLEASE HELP
Hi,i think the problem is with the needle bar,the alighnment has been distorted internally,i think you should re-align the needle bar in order to restore your machine back to a normal working condition.\015\012\015\012\015\012Thanks and t ... Vacuums
Vetus bcc 1000 inverter/charger When this unit is started it goes into overloadthe battery bank is new and we have isolated it from the narrow boat electics and pluged in a fan heater but still it goes into overload.
My roomba mounts up to the charger the light blinks red then after a time it goes green but when I dismount it and push the green button it immediately goes red. It doesn't beep or do anything. It is that the battery is not charging?
You have dead nimh (nickle metal hydride) batteries. You\012will need a replacement. You can test for this by removing the battery\012and holding the power button for 15 seconds. This will restart the\012charging cycle as if the battery were new. ... iRobot Roomba 560 Robotic Vacuum
I inherited a Simplicity 4380ED serger. It won't cut the fabric. I changed the lower blade for a sharper one. It is lying level with the throat plate. The upper blade is smooth. The fabric edge goes along the upper cutter and rolls over from the top and goes through the serge stitching.. No cut.
A tech on this site wrote this, when a similar model as yours was "mangling the fabric":\015\012Best Solution\015\012posted on Jul 07, 2009\015\012\015\012\015\012 \015\012\015\012 ... Vacuums
I have a Bissell steam shampoorer..I'm not sure where the water goes. I assume in the bladder (soap & water)..there is a little red plastic piece that I don't know where it goes..somewhere in the bladder?..Anyway, no solution is coming out and of course no vacumming up. Cannot find my manual or instructions. I've had it working before..thanks
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
Where does it go and how do I replace the belt on a Deluxe Hoover Mach 3.8 bagged windtunnel action vacuum? I kno it goes somewhere around the brush but it fell off when opened and I can't tell where it goes. I have a replacement belt
... Hoover Vacuums
Shuts off frequently The sweeper will run for a few minutes and when it starts to get warm it shuts off. If you allow it to cool off it will turn on again and run until it gets warm
Check any filters to see if they are clogged up with dust because its overheating the motor causing the thermal switch to trip. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum