Having problems with your Vacuums ?

I have a Janome JFS 1812 i lost the manual .and after having it stand for years i a cant get the bobbin to stop tangling and knotting on the out skirts of the bobbin casing ..is there a manual i am doing something wrong


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Janome JFS 1812 i lost the manual .and after having it stand for years i a cant get the bobbin to stop tangling and knotting on the out skirts of the bobbin casing ..is there a manual i am doing something wrong


... Vacuums

Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st


Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums

I have the Janome 6600 P. Beginning a seam the thread knotted and the machine made noise and needle would not move either up or down. I manually moved the needle using the handwheel and cut away the knotted thread. I began sewing again but instead of starting at the edge began about a half inch down, forward stitched, reversed to lock threads and problem repeated and received the message to "Stop for safety purposes". Did that. Referred to the manual, tried manual recommendation. Did not work. I


... Vacuums

I have a Kenmore 385.19110 model machine, and the straight and zig zag stitches work just fine, but when I follow the directions in the manual to do a satin stitch (which is use the lowest stitch length) it creates a line that isn't perfect, or uniform, and after an inch or two stops catching the bobbin underneath. Have already tried reinserting the bobbin, rethreading the machine, refilling the bobbin, changing the bobbin, cleaning the needle, changing the tension. Wondering if I just got a mac


... Vacuums

Hi I am looking for Lervia 564 sewing machine manual I was rethreading the bobbin and the casing fell out now It won't pick up the thread from the bobbin


... Vacuums

How do I put the bobbin case back together? - SewShop.com Singer Model 522 Instruction Manual


Click this link for manualhttp://www.singerco.com/uploads/download/97c8866f3501ae8f2e7ea570ce3dd88d210aa50c.pdf ... SewShop.com Singer Model 522 Instruction Manual

Needle hitting bobbin case - SewShop.com Singer Model 9020 Instruction Manual


... SewShop.com Singer Model 9020 Instruction Manual

Our beautiful Bernina 730 sewing machine has been stored in the garage in its original case, and that wrapped in plastic, for a few years now. Temperatures have been both hot and cold in the garage, but the environment was dust-free. We have brought the Bernina in, set it up, oiled it as specified in the manual, with the original sewing machine oil. We have correctly threaded the machine and the bobbin thread is up. When we press on the pedal to sew, the machine gets electricity and buzzes


Hello and thank you for using Fixya ....From what you describe there can be only 2 causes...Either the machine is still stuck ..and the motor buzzes cause it can not spin it ..and in this case it needs to be oiled more..and be spun by hand unt ... Vacuums

Jun 24, 2010 - Jun 24, 2010 - Needle not bent/ new needle not answer. I finally conclude that the entire bobbin case is ROTATING in its seat, which jams the needle. The "projection" is against the "spring" when I install it, but I can rotate the bobbin case PAST the spring without trying very hard. Bobbin case MIGHT get held in place better if it were closer to me (front of machine). I feel it is still not out from under needle plate as shown in diagram, but can't keep it closer to f


Hi,Your problem dated 24th June 2010 was re-posted today. If it has been already resolved, kindly ignore this message.Thanks for using FixYa ... Vacuums

So, I was sewing along and heard a thump...kind of sounded like a louder version of what you hear when the needle hits a pin...but I wasn't using pins. This, of course, lead to the thread jamming so I had to clear that. When rethreading I pulled out the bobbin case to make sure it was seated correctly and found a kind of "v" shaped piece of wire (about the width of a paper clip I guess) sitting loose under the bobbin case. I took it out and threw it away. Still can't pull up the bobbin threa


That part was the hook end of the spring that was supposed to put tension on the bobbin - it will have to be replaced. This is a special flat spring that unfortunately only a repair shop of a dealer has it - you will have to take your machine to one. ... Vacuums

How do I install the bobbin case and bobbin case body in a model #9420 singer sewing machine


... Singer Instruction Manual - 9420

I have a Singer Model #4562 sewing machine. I am having trouble adjusting the tension. Everytime I try and turn the knob to adjust the bobbin just gets looser. Right now it just snags and gets caught underneath the material and bunches up into a big ball. There is a lot of thread inside the bobbin case that came out of the bobbin and has to be cut out to free the material. How do I fix this mess. I am a novice at this. I have not sewn in several years and would like to sew a few quilts


... Vacuums

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

I have a Pfaff Classic Style 2025. After clearing a thread jam in the bobbin area, the machine will not sew. It works without thread, but I think the bobbin case is crooked. The bobbin opening is off to the right, not up, as it needs to be.


... Vacuums

I took out the bobbin case & not sure if I put it back correctly. Now I had my thread going under it instead of over it.


Download the manual here > http://www.singerco.com/accessories/instruction-manuals ... SewShop.com Singer Model 4562 Instruction Manual

Cant figure out how to thread elna 1000 lotus sewing machine. also the bobbin keeps getting tangled. if you could send me a diagram on how to thread and bobbin i would appreciate it


... Vacuums

I have recently got my sewing machine out after several years of it lying unused after moving house. I cannot find the manual. Where can I get a copy of this manual.The second request is that i need to put different cotton onto the bobbin and can't work out how to remove it from the machine. there is a clear "plate" over the bobbin , but I can't seem to remove that.


You posted in the wrong category and there is no mention of make/ model in your question so sadly it is impossible to help you.If it is any consolation this is in part due to the very poor way that the fixya question posting process works. ... Vacuums

This is not an electrolux problem, but I am hoping one of the experts can answer the question. I have a Sears air compressor that suddenly stopped working. After looking at how the motor case is put together, it appeared that it would essentially have to be destroyed to get it apart and into the motor. I received a new compressor for my birthday so I decided to tear into the old one to do some diagnosis. After getting into the case where I could see the motor/pump, I have discovered the prob


This is intersesting. I think the fuse is simply a heat sensor. If you by pass this the only problem you may run into is if the motor over heats it my eventually burn out. However, for what you are using it for overheatin should not be an issue. This ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

The rotating brush stopped working after it grabbed a matress skirt. The skirt did not roll up into the vacuum. Is there a rest button?


Did it smell like burning rubber? If it did the belt is probably stuck and needs to be replaced. You can look at the little black belt on the bottom of the vacuum and see for yourself.You may have a extra belt that came with the vacuum. I fnot you ca ... Dirt Devil Vacuums

I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me


Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums

Which way is the bobbin winding when put into bobbin case > It will not pick up the top thread


... Vacuums

I have a brother project runway limited edition sewing machine and there is a constant jam with the bobbin threading and I have cleaned it,removed the sewing plate and everything I can possibly think of. If the bobbin case is scratched would it cause the jam?


Hi The usual cause is that there is a problem with the upper \015\012threads, often it is not caught in the tension discs. When you thread \015\012the machine, make sure that the presser foot is raised - this causes the\015\012 te ... Vacuums

My kenmore sewing machine (Model #385.11803) isn't picking up the bobbin thread. Bobbin thread case isn't turning. HELP!


... Vacuums

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Kenmore YM-40-35 R Sewing Machine Manual (or copy) wanted. If a manual is not available, I'd be OK with instructions for threading the needle and bobbin and any additional details that an expert may have. I think the machine may be a Canadian model number, it looks old, made of metal with screwed in presser foot. Thanks v. much. Elizabeth, [email protected]


Hello,please kindly visit the site below to see the comprehensive instruction with video on how to thread and bobbin your sewing machine.http://www.wonderhowto.com/how-to-thread-mechanical-singer-sewing-machine-224245/wish you ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0521 seconds