Having problems with your Vacuums ?

I hit the button and just the light comes on,then i hit the button again and the door closes almost all the way but opens and light keeps flashing . the sensors are on and clear of obstructions . it is a wayne dalton quantum 3212 garage door opener.

Answers :

Hello ccap..... It sounds like one of those sensors has gotten out of alignment with the other. check to see if there is a steady green light on each sensor. If not, adjust until the light is a steady green. Joe
\015\012Thanks for choosing Fixya!
There are two possible solutions. The first is that the optical sensor is not working correctly. To test this, start the door closing and then interrupt the light beam. The door should stop immediately and go back up. This will verify the operation of the electric eye circuit board.

The other is the adjustment of the closed sensor. The first thing I would check is that the door moves freely to the closed position. To do so, disconnect the lift mechanism and close the door. You will need to take the proper precautions when doing so. The door should still be spring loaded and operate as a normal garage door. If there is no increased friction, then you need to adjust the door opener. If you do not have the manual on your opener, let me know and I will get you a copy and give you step by step instructions.

Good luck and remember to be safe when operating the opener.

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I hit the button and just the light comes on,then i hit the button again and the door closes almost all the way but opens and light keeps flashing . the sensors are on and clear of obstructions . it is a wayne dalton quantum 3212 garage door opener.

Hello ccap..... It sounds like one of those sensors has gotten out of alignment with the other. check to see if there is a steady green light on each sensor. If not, adjust until the light is a steady green. Joe\015\012\015\012Thanks ... Vacuums

I have a Liftmaster garage door opener and the garage door faces south. Normally the opener works great except at certain times on a sunny day.The sunlight is not directly hitting one of the sensors but the door will comedown as far as half way and then it will go back up and the lights will flash. If I go inside and use the button I can hold it down until the door is fully closed. However, sure is a pain to have to take the car out, go back into the garage, shut the door and then leave the h

Sounds like a problem with a limit switch or something getting in the way of the electric eye that interrupts for safety reasons. \015\012Clean the electric eye transmitter and sensor of debris and cobwebs and make sure the wires are attached properl ... Vacuums

I have a littermaid elite automatic litter disposal system. It stopped cycling and both lights are flashing. Nothing is stuck, it just made several passes at some point overnight without successfully getting to the receptacle due to heavy litter. The box was clear and moving before we went to bed. This morning the lights were flashing. I unplugged, emptied, etc and it will not work. what now? It does not have the reset button at the receptacle button that the old models did. Is there one?

... Vacuums

My irobot Dirt Dog won't go into a cleaning cycle. It is charged, but when i hit the clean button it does nothing. new battery installed a week ago. the LED lights under the "clean" button are flashing in sequence, "Green, Green+Red, Green". Then the sequence immediately stars over. Can someone help me?

Hi, A very common problem with the I robot is the wheels on the underside become clogged with dust and dirt. Turn the device over, and remove the bottom cover that is covering the wheels. At this time, remove the dirt and blockage from the wheels, an ... iRobot 1100 Dirt Dog Bagless Robotic Vacuum

No power to sensor SR 12. I also have cleaned rollers and filters and bags. I have reset the handle. When I hit the power the check brush and full bag lights flash once. That is the only power that is getting through.The unit was in storage for a bit and got wet but its been drying off for a couple months. Is there something I can check or replace. Its a great Vac.

... Windsor SR12 Sensor Bagged Upright Vacuum

Have a Genie 2020L garage door opener. Door start to go down then stop and return. Tried cleaner old sensors. Same. Noticed red light on sensor 3blinks then off....repeat constantly. Replaced sensors - same issue. Reset unit...checked all wiring...no jams anywhere.... HELP PLEASE L:-)

... Vacuums

I have a remote Hunter Ceiling Fan w/ remote 1-2-3 fan speed buttons and one on/off/dimmer light button. Model Number CP-9110R. It only has one pull string and it is for the light. I would like convert the light to work off of a simple wall on/off switch and the fan to be controlled by a 3-speed pull string. Can I by-pass all the sensors and make it work?

I see noone has answered so I will.Yes,it could be done,but if there is not a conversion kit for your fan,it would not be wise to do it.For starters,all of the things required would probably cost at least $15.Also,there is at least one tool you would ... Vacuums

Err5 When charging the battery, it starts out flashing amber, but after several minutes it turns red and the err button flashes five times. The troubleshooting says to hold the buttons above and below the power button for ten seconds and this may resolve some software issues. I tried that but it goes back to the amber light then red again. I replaced the battery hoping that was the issue, but it still does the same thing.

... iRobot Roomba 530 Robotic Vacuum

I have a genie screw type garage-door opener. the fuse blew on the moter drive board , now the door only opens when you push the light button on the wall console ,will not go closed.green light blinks continually. when I power it up it jumps closed then nothing. It seems like the motor is not reversing.

... Genie Company Vacuums

I was vacuuming with my DC28 Animal and all fo a sudden the beater bar stopped working and NONE of the floor mode buttons work.. no lights or anyhting. I checked for obstructions per the Dyson manua

... Dyson DC28 Animal Bagless Upright Vacuum

I have a new scoba (irobot) the battery is charged the tanks were fillied and every time i hit the power button and then clean the machines "check the tank" light came on. i have done all the proper instruction checks an i have done all the trouble shooting section. the machine will only work (and that is for 5 minutes drying its head) when i hit power and the clean button twice. so obviously the machine is somewhat working

We had to prime the sensor. irobot suggested a turkey baster, but we didn't have oneso we used an empty visine bottle with the end snipped off and rinsed completely. this worked after the first try. thank you for your interest ... iRobot 5800 Scooba Vacuum

Hi, I can't get the warning lights to stop flashing on my vacuum.... it had caught a string on my door mat... I removed the string, did all of the trouble shooting that my guide recommended including looking for blockages etc. The vacuum seems to **** fine except I can't change the settings and the lights won't stop flashing...any advice? I bought it out of country so I have no warranty (so much for me saving over $100 in price!!)

Try to reset or find the reset button it means the trouble about the string was on the memory of your vaccum that trigger the flashing of light. try to unplug your unit then after plug it on ... Dyson DC28 Animal Bagless Upright Vacuum

Electrolux vacuum brush not turning problem: was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won't even switch on. Hope you can help

Under the vacuum, there is a guard.\012remove the guard , either by 2 screws or by 2 clips.\012there is a belt under the guard.\012that is connected to the brush.\012the belt need to be replaced. ... Vacuums

My purple Dyson Animal (without the ball) isn't working correctly. When I turn it on, the red power light, as well as the medium pile buttons flashes. When I first turn it on, the brush rotates for 3 to 5 seconds, then once I start moving the vacuum, it stops and that's when the lights start flashing. I've checked the filters, they are dry and installed correctly. What could be the problem?

I need help repairing my Dyson. I cannot push the buttons down to select Short pile/Medium pile or bare floor. The buttons will not push down at all. It will not allow me to select anything. I have very short pile carpet so it does not pick up that w ... Dyson DC28 Animal Bagless Upright Vacuum

I have a Kenmore Progressive upright model 216-37100800. It is only around 1.5 years old. My wife said that one day after she plugged it and turned it on, it whirred up but then shut off. Since then it will not start. I have noticed that right after I plug it in, if I try to turn it on, the first yellow light in the series of dirt sensor lights turns on then shuts off. After that the light will not light up on pressing the power button, unless I unplug it and plug it back in again. I have seen o

... Kenmore 25512/ 25513 Progressive Canister Vacuum

Electrolux Unirapido not working green light flashes when start button is pressed!

I have the same problem with this type of vacum. I have tried a lot of things but the problem is with the software included in a 20 pins chip on the pcb so it can not be repaired. But, if you look in the back of the vacum there is a rubber stopper wi ... Vacuums

After a brief power outage my Marantec 4700 garage door opener has problems opening/closing. When opening it stops at the fully open position and the lights blink, when closing it automatically reverses just as it fully closes and then the lights start to blink again. I checked for obstructions and tried to reset the limits of travel per the manual, it still does the same thing. Any ideas on what to try next?

This is not a sensor issue, I have a similar problem, sensors work fine, garage door is still fully functional, all operations, including safety sensors work properly, just the overhead lights flash. I suspect there was damage to the power board due ... Vacuums

Have Model 350A with Chime Model MC3. Door bell does not work. Light is on at the button outside so there is power there but when you push the button - no chime at the intercom system

... M&S Systems Vacuums

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely

The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

I have a hoover Core vacuum. The problem is that the blue light flashes (as normal) when it is plugged in and the power is turned on and the blue light stays on (as normal) when you turn it on at the button but it makes no noise and doesnt work. All of the filters are clean. Can you help please?

... Hoover Vacuums

When I flip the switch on my sebo x1 upright, a red light comes to the brush and bag icons. However, I cleaned out the hose and checked to make sure there is no obstruction from the brush to the hose also, or from the hose to the bag. It is clear that juice is coming to the vacuum, but there is no sign of life except the two red lights.

Thanks for contacting fixya. You should pull out the bag and reset the machine. You should take all the user replaceable items. And turn it on. You will get lot of errors. Then turn the machine off. Put back all the accessor ... Sebo Automatic X1 Bagged Upright Vacuum

My shark vx3 vacumn has stopped running... i tried recharging it, but still no luck... i then put a new battery pack on it and tried recharging, still it won't run... the charge light, (green) is on, the three red lights come on and flash when i push the on button...what should i do next?? this unit is about 6 months old... help!!

... Euro-Pro Shark Cordless Stick Vacuum SV775R Vacuum

Hi, the main box where all the wires connect to the sensor has the power on, and i've just noticed the small box where you enter the code to set the alarm does not work, yet the buttons are illuminated, normally the led light displays to show the power but no led's are on, the buttons doesn't work to set the alarm. Can you please hepl, many thanks.

Difficult as you didn't say what the equipment is but it sounds like there is a problem with communication between the main box and the keypad box. Have someone check that all the wires in the keypad are connected and there is no break in one of the ... Vacuums

Bissell spotbot manual button doesn t work light just flashes

... Bissell SpotBot Hands-Free Compact Deep Cleaner - Silver

The green light on the power head was flashing and then it went out and the brush quit turning. Is the a reset button?

No reset button. Most likely your belt broke or it has to be replaced. How to replace the belt look at instructions on our website:http://www.goodvac.com/artic ... Kirby Ultimate G Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0771 seconds