Having problems with your Vacuums ?

Ambient hard 5628 - Vacuums


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Ambient hard 5628 - Vacuums


... Vacuums

My windsor sensor 12 inch vacuum is to hard to push. I bought a new one and its doing the same thing. My vacuum repair man says he cant fix the problem. My shoulders are sore from working so hard. Help


It\\'s possibly the type of carpet you\\'re using it on. The sensors use the brush speed and the amount of air flow to determine carpet height. Some berber, and tweeds make these things horrible to push. We sell sebo, who make the windsor and we\\'ve ... Windsor SR12 Sensor Bagged Upright Vacuum

I have a Dyson vacuum cleaner ...upright....all of a sudden my vacuum started making this awful sound...like a loud buzz...but only when I have it on carpet....when I have it on "floor" mode it's fine....sometimes(although seldom) it has worked without buzzing...and it's LOUD!!....I have only had this vacuum for a year....and no...I have never picked up any coins or hard stuff.only use it for 2 rooms.the rest of the house is wood floors.......what shall I do? Thanks......Gloria


It may just be, that on carbet the brushes make noise that you dont hear on woodfloors.\015\012If there is a hights adjustment, set it higher for shaggy carpet and lower for berber. ... Vacuums

My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.


When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Engine troubles I have a 1975 4x4 GMC full size van. The motor is a 350 cid small block on propane. The thing hadn't been running in 5 years and when I tuned it up I changed vacuum advance pod on HEI distributor and hooked to a better vacuum and now the hotter it gets the faster it idols and when I try and turn the timing back, it starts hard. Wondering if vacuum is too strong or what is up?


I haven't fixed it yet but I think I might have a solution for it. From the factory this thing had a 4 barrel carb and they put an equivalent size atomizer in it for the propane and over the years someone omitted the EGR system in it and propane is a ... Vacuums

Does not vacuum effectively. It smells like it is burning. I have only had this one year and hardly use it. When I brought it to a local vacuum repair place, he wanted to sell me another one, and, of course, wanted to trade mine towards another.


Miele vacuums are famous for having hair and carpet fibers getting caught in the roller bearings. That can cause a bad smell. The motors in Mieles are very well built and I have a hard time believing that the suction motor is going bad in 1 year. ... Miele S548 Bagged Canister Vacuum

When switching the vacuum (DC17 Animal) over to the hard surface setting (so the beater brush is not spinning), the vacuum shuts off. I cleaned the dust bin and checked the filter. I also cleared the beater brush of hair or debris that was wrapped around it. It still shuts off. Ideas? Thanks.


The drive belt has probably broken. You can get a replacement belt here:Dyson DC17 Belt ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The vacuum is very hard to push on carpeting even when on hard floor level.


... Hoover Tempo Widepath Upright Vacuum - Blue

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha


... Eureka Smartvac 4870 Bagged Upright Vacuum

I just bought a Dyson DC 14 All Floors Vacuum and assembled it exactly as the manual said. It sounded normal as I went over hard floors but as soon as I went on carpet, the vacuum was extremely loud. There's no strings or debris in the powerhead... what else would cause this?


There is a knob setting at the footing for carpet and bare floor can help. Otherwise check out a little plastic for suction path from the bottom to the dirt container: it may loose, just snap it in. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u


Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

I just bought the LG200R vacuum. It is working wonderfully but i have only had it a week. I have already had to clean the agitator but this is due to my extremely long hair and apparently i shed a lot. I was wondering if i should be alarmed by the funny smell it leaves in the air. Its not like a burning rubber smell but more like a fresh plastic smell or sorta chemical like smell (hard to describe) and it doesn't need to be on to make this smell it seems to be permeating off the vacuum itself


... LG LUV200R Bagless Upright Vacuum

When pushing foreward the vacuum is hard to push and if pushed on to hard it will turn over on itself.


My dyson dc17 animal had become nearly impossible to push on carpets. sure enough i found that my roller was warn down to nubs (vacuum is probably 8 years old, and gets used nearly every day) I replaced the roller and WOW! it feels ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?


This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Vacuum hard to push - Oreck XL21 Bagged Upright Vacuum


You probably have a broken belt. replace it ... Oreck XL21 Bagged Upright Vacuum

Vacuuming it is hard to move forward when vacuuming,ok when moving back


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=11561&thid=725106\015\012Vacuuming\015\012Posted by egarcia on Jun 30, 2008\015\012It is hard to move forward whe ... Kirby G5 Bagged Upright Vacuum

Loud noise I have a brand new Dyson and it is great on all my floors except one of my area rugs when it starts making this really loud vibrating noise. I am not sure why - nothing is stuck in the roller or vacuum and it doesn't make it on any of my other rugs. Also it is really hard to push whereas all the other floors it just glides. I don't want to return it but I also don't want to hear this sound every time I vacuum.


This is the clutch as it jams up in the brush. Usually happens with rugs that are not secured to the floor. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Its hard to explain, I have a 4704 p Boss LightWeight Upright. The piece that holds the bagless cup onto the vacuum broke. So now the cup falls off, is there a way to get another piece or would i have to by a new vacuum for this one little piece being broken


Should be able to order what you need. Find a local shop, along with your model number, they should be able to order it for you. ... Vacuums

My bissell 3595-2 vacuum cleaner started turning off the power automatically. Now I can not get it to turn on. This vacuum cleaner is still in real good condition, as I have hardly used it. Please advise what could be wrong. I was thinking maybe a loose connection with the on-off switc.


... Bissell Vacuums

Levels/Settings I am having trouble changing the setting on my vacuum from 1 or "Low, Hard Surface" to any other setting. Without changing it, I am unable to vacuum on my carpet, since the setting is too low.


These height adjustments are designed so that they will not adjust when the handle is in the "back" position. This is so they will stay where they are set and not self-adjust while you are vacuuming. To change the setting, you need to return the hand ... Hoover Elite Rewind Bagless Upright VacuumVacuum

Hello, my Kenmore 27514 canister vacuum only works on the hard floor...the carpet suction stopped working while I was using it. Is there anything I can do to fix it or is it necessary to take it in for repair? The vacuum is only 1.5 years old. Thanks. Susan 702.340.8015


You need to replace the belt that drives the beater bar. You can do this yourself very easily. If you need help, let me knowJim ... Kenmore 27514 Bagged Canister Vacuum

I have a Eureka "The Boss" vacuum that doesnt seem to be sucking up as much as it should and did in the past when vacuuming on carpet and hard floor surfaces.


I have a Eureka "The Boss" vacuum that doesn’t seem to be sucking up as much as it should and did in the past when vacuuming on carpet and hard floor surfaces.\015\012 \015\012I woul ... Vacuums

My vaccum has a 3 position handle. This no longer works, so I have to pick up vacuum to move it. Makes it hard to vacuum scatter rugs. It does not lock into place


What is the brand and model of the vaccum? the description i see says Hoover U6311930. When I check the info for this model it gives me maytag vaccum cleaner. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

I've just purchased a Bosch BX1 1600 vacuum cleaner in Spain, and already I've lost the hard furnishing brush, the crevice nozzle, the upholstery nozzle, and the hard-floor brush that I think were in the box. Is there a place to purchase these separately? Thanks, Dave Wass


Hi Dave,Are you in the USA? If you are, try this web address: >>>> http://www.bosch-eshop.com/eshop/bosch/us/brushesfloortools.htm Copy and paste the address into your browser and the tool page will open up for you.Should you ... Bosch Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0614 seconds