Having problems with your Vacuums ?

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.


Answers :

Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.
\015\012
\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug the unit before you attempt any maintenance, then you should not have any trouble with the repair.
\015\012
\015\012Just be sure to keep track of all the screws you remove, and if different sizes are used in different parts of the vacuum, keep them separated and labelled so you can reinstall them in the correct places later.
\015\012
\015\012If the unit has a cover over the collection bag compartment, be sure to remove the cover and the bag to check for additional screws in that compartment.
\015\012
\015\012Other than that, just remove the visible screws holding the cover in place and then carefully remove the cover. If you need to reconnect the power supply wires from the cord to the vacuum, you may need to use a soldering iron, depending on how they are connected.
\015\012
\015\012Please comment back here to this page if you have any questions, wish to provide the model number for your unit, or just require further general assistance and I will respond as soon as I see it here.
\015\012
\015\012If this was at all helpful please click on the 4 Thumbs Up helpfulness rating icon you see on this page.
\015\012
\015\012Thank you very much and good luck.
\015\012
\015\012Joe.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.


Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa


... Electrolux Vacuums

I need to know how to hook the wires up to the start switch. There are two wires from the external cord and two wires from the internal cord.


White wire to neutral black wire to hot if you post colors I could help you red ,orange, black,pink, blue, or violet are usually hot guessing a striped wire is usually neutral please post colors ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Inside the vacuum handle of my Wertheim 5030 1800 there is a white earth wire that has a sprung loaded clip on the end. Does anyone know how to put this back into the right position as I opened it up to clean some wet plaster from inside and it became misplaced.


... Vacuums

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating


... Vacuums

I need to get to the internals of the machine in order to retape the electric wire that originates inside. I have removed all of the visible external screws that are keeping the 2 sides together but it still will not open. It is a Euro-Pro vacuum model ep 601. Can you help?


\015\012\015\0121. \015\0121 Lower handle of vacuum and flip\015\012over so that it lies flat on floor upside down.\015\0122. Twist 3 plast ... Euro-Pro Vacuums

I am trying to replace the power cord for my 82 year old father-in-law's Oreck XL 2600HH. He already took it apart. I need to know where the semi U shaped spring steel piece is supposed to go inside the Helping Hand Handle? Any drawings or schematics available? Thank you for your time. Arthur


That justs lies on the inner handle whenb you put the spring back. There should be two holds where each end of the spring sits in. ... Oreck XL Ultra Bagged Upright Vacuum

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?


As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I need to replace the cord rewinder of my Nilfisk King series 500 vacuum cleaner, but I do not know how to open the device or where are the screws. Can you help me?


Http://www.youtube.com/watch?v=13krERCaP0U ... Vacuums

Need to replace power cord on Hoover windtunnel need wiring help


Without seeing this it would be difficult to describe. I would take it to a vac shop and let him show you. there are no real schematics for the wiring of these units. I usually would cut off the cable with a few inches of insulation to know where to ... Hoover U5399-900 WindTunnel Lite Upright Vacuum

Vacuum won't switch on;got it apart;cord ok;need wiring diagram


Its a great idea to write on paper how its connected . So it helps with dis assembly & reassembly . I tried a Internet search . Looks like it'd cost money for a service manual. Though. I found a Kirby Spares Website that could help. Although it d ... Kirby Generation 3 Bagged Upright Vacuum

I own an Oreck 2310RS upright vacuum cleaner. The cord is too short for my needs. The cord I need is a two wire 25 to 30 foot cord. Where can I buy this vacuum cord and how do I connect it? Thanks, Don


You can buy one at a oreck store but i would tell you to use an extention cord ... Oreck XL2200 Bagged Upright Vacuum

My friend has a Tristar MG1 vacuum. The cord was


Chances are that there is the tiniest fray of one of the wires touching somewhere. Since you have already made a good repair with nuts and tape, feel the length of the cord for other bite marks where a puncture might short the cords. If you find s ... Tristar Vacuums

The Lifesaver smoke alarm model 1225 is hard wired, no battery and is chirping. I have it pulled out with wires coming out of the back, but can't open the front face to get in to disconnect the wire. Anyone know how to open it up?


Hi, you should be able to grasp it and twist it to open/remove it from the juntion box to expose the 120 volt wires. They do not open like one with a battery type, so twist it I believe CCW to remove it from the box to disconnect the wires. Please be ... Vacuums

How to open case??


In an unsuccessful attempt to swap out the motor in a 12 Amp turquoise modeI curbed b/c some nut had Gorilla Glued the wheels on) with the motor from my 11 Amp maroon one with a broken (poorly designed button covering the switch that would turn itsel ... Kenmore 22313 Bagged Canister Vacuum

Need to replace power cord and can't find how to open canister to replace


I had the same problem and could not find the other screws. You need to pry off the power cord retraction button, you will find two more screws under there. It's pretty easy after that!!!! ... Kenmore 22612 Bagged Canister Vacuum

Need connector wires inside wand. Electrolux central vac. 16" wand 1 1/4" wand dia. Don't need wand, just the wires.


Go to a store like Lowe's and look in their electrical department. You need wire the same gauge size (stranded or solid) and comparable insulation. Hope this helps! ... Vacuums

Need proper wiring connections inside unit, where they have pulled apart from squeeze connectors.(Wiring diagram needed) Can someone E-Mail this to me? Fritz (an ''old'' mechanic) Folks I have talked to, say there is no specific model number for these units. They are just described by name, and serial #. and I have relayed exactly what was labled on the unit. Please post this and quit asking me to enter a "valid" product.


Fritz , thanks please confirm... there are likely more than 2 leads from the motor?? I have not seen or worked on the Tristar CXL as it is very new.You will have a high low function but: Should the power head function at both spee ... Vacuums

Need a wiring diagram for a karcher puzi 100 yellow. Mainly need to know which way round the wires go on the switches?


... Vacuums

I need to replace electrical cord on hoover windtunnel UH70120. How do i get the cord reel off? Can i open the cord reel to replace the cord?


... Hoover Company Wind Tunnel U53019 Upright Vacuum

Need to open rotating brush part of vacumm as motor functioning but roller not turning...perhaps belt broken put need to get into ..inside brush box ...Need help need instruction with diagrams Thanks for help Robert


... Panasonic MC-V9638 Bagged Canister Vacuum

How to wind cord onto spring loaded retractable cord reel for a Kenmore canister vacuum. There is a metal 'U' shaped, spring loaded, piece that fits over the outer aspect of the wheel. If cord needs to get wound on under this metal band I can't figure it out and the band is like factory sealed onto the wheel. Also. I don't know which direction to feed the cord onto the wheel


What is the exact model # please?Thanks!! ... Kenmore Vacuums

Rowenta Effective Steam Iron DX1700 Need wiring diagram. How do I wire the power cord to the internal Red, Blue, and White wires? What wires are neutral and which are hot?


... Vacuums

The retracktable power cord on my Panasonic MC-E7103K is jammed inside the machine. Does anyone know how I remove the cover after removing the two visible screws? Brian


... Panasonic Vacuums

The handle was getting hot and we opened the handle and the wires were melted around the switch. I need a part number for it. All I have seen are 2 wire and this is a 3 wire. Thank you.


Had exactly the same problem with my upright Eureka Model 5893\015\012bagless. Eventually, the handle would get hot, and finally it just\015\012quit. When handle was disassembled, the wires were melted and it was\015\012toast. Ordered a switch aft ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0738 seconds